Casio PV-750 Plus Manuel d'utilisation et d'entretien

134

Chapter

11 Data Communication

Data communications capabilities let you transfer data between two CASIO PV

Units, between a PV Unit and a BN-10/BN-20 Unit, or between a PV Unit and a

BN-10A/BN-20A/BN-40A Unit. You can also receive data from a CASIO SF,

CSF, or NX Series Unit, and communicate with a personal computer using PC

sync for Windows.

• See the manual that comes with PC sync for Windows for details on connecting

to a computer and setting up for communication.

Using the Cradle

The PV Unit comes with a cradle that helps to make data communications quicker

and easier. The following procedures describe how to attach the PV Unit to and

detach it from the cradle.

To connect the PV Unit to the cradle

1. Turn off PV Unit power.

2. Place the PV Unit onto the cradle.

• Gently but firmly press down on the PV Unit to ensure that it is inserted

into the cradle as far as it will go.

135

Chapter 11 Data Communication

To detach the PV Unit from the cradle

1. Turn off PV Unit power.

2. Lift up on the PV Unit while holding down the cradle’s Release button.

Data Communications Between Two PV Units

This section describes how to set up and communicate between two PV Units.

To connect two PV Units

1. Make sure that the power of both units is turned off.

2. Place the PV Units onto their cradles.

• Gently but firmly press down on the PV Units to ensure that they are

inserted into the cradles as far as they will go.

Release button

136

3. Use an optional SB-90 9-9 pin connector to connect the two cradles to

each other.

• All data communication settings must be made on only one of the PV

Units only. This unit is called the host unit, while the other unit is called

the terminal unit.

To send data from the host unit to the terminal unit

1. After connecting the two PV Units, turn on the host unit.

• Terminal unit power should still be off at this time.

2. Display the list view in a mode whose data can be sent with this setup.

• This configuration supports transfer of Contacts (Business, Personal,

Untitled 1-3, Phone Book (Phone), Phone Book (SIM)), Memo (Untitled

1-5), Schedule, To Do, Reminder, Expense Manager, and Quick-Memo

data.

Start button

Cradles

SB-90 9-9 pin connector

Host unit Terminal unit

137

Chapter 11 Data Communication

3. Tap the Menu Bar icon to display the menu bar, and then tap System –

Data communication.

4. Tap the button next to Pocket Viewer to specify the data communication

configuration.

5. Tap the button next to Send.

6. Tap Set.

7. Tap the check boxes to specify the data you want to send (checked) and

the data you do not want to send (unchecked).

8. After everything is the way you want it, tap Set.

9. Turn on the power of the terminal unit and then press the Start button

on its cradle to start the data transfer operation.

138

To receive data from the terminal unit on the host unit

1. Perform steps 1 through 4 under “To send data from the host unit to the

terminal unit”.

2. Tap the button next to Receive.

3. Tap Set.

4. Tap the check boxes to specify the data you want to receive (checked)

and the data you do not want to receive (unchecked).

5. After everything is the way you want it, tap Set.

6. Turn on the power of the terminal unit and then press the Start button

on its cradle to start the data transfer operation.

139

Chapter 11 Data Communication

Notes

• The above procedures can be used to send or receive all data in specific

modes only. You cannot send or receive individual data items.

• Data communication can be interrupted at any time by pressing Esc.

This causes the message Stopped! to appear on the displays of both

units.

• The message Communication error! appears on the displays of both

units whenever data communication is interrupted due to cable

disconnection, line noise, or other abnormal condition.

• If the secret memory area is accessed on a unit receiving data, the received

data is stored in the secret memory area, regardless of the memory area

the data is in on the sending unit.

• When you exchange data between the PV-750Plus and another model

PV Unit, the Phone Book (Phone) category corresponds to the Untitled

4 category of the other PV Unit, while the Phone Book (SIM) category

corresponds to the Untitled 5 category of the other PV Unit. The Free 2

fields of the Untitled 4 and Untitled 5 categories correspond respectively

to the Mobile fields of the Phone Book (Phone) and Phone Book (SIM)

categories of PV-750Plus Unit data. If a Free 2 field does not contain

any data, blank spaces are input into the corresponding Mobile field

when data is sent to the PV-750Plus Unit from another model PV Unit.

• Transferring data from the PV-750Plus to a PV-100 or PV-200 causes

all euro symbols to be replaced by spaces.

• The size of the PV-750Plus screen is 160 ×160 dots. Transferring

PV-750Plus Quick-Memo data to a PV-100 or PV-200, which both have

98(V) ×124(H)-dot screens, causes the right side and bottom part of the

Quick-Memo image to be cut off in order to fit the PV-100/PV-200 screen.

140

Data Communications Between a PV Unit and

a BN Unit

This section describes how to set up and communicate between a PV Unit and a

BN Unit (BN-10/BN-20 or BN-10A/BN-20A/BN-40A).

To connect a PV Unit to a BN Unit

1. Make sure that the power of both units is turned off.

2. Open the cover of the Mini Cradle port of the BN Unit, and connect its

Mini Cradle to the port.

3. Place the PV Unit onto its cradle.

• Gently but firmly press down on the PV Unit to ensure that it is inserted

into the cradle as far as it will go.

4. Use an optional SB-90 9-9 pin connector to connect the PV Unit cradle

to the BN Unit Mini Cradle.

• All data communication settings must be made on the PV Unit, which is

the host unit. The BN Unit is the terminal unit.

START button

Mini Cradle

Cradle

SB-90 9-9 pin connector

Host unit (PV Unit) Terminal unit (BN Unit)

141

Chapter 11 Data Communication

To send data from the PV Unit to the BN Unit

1. After connecting the two units, turn on the PV Unit.

• BN Unit power should still be off at this time.

2. Display the list view in a mode whose data can be sent with this setup.

• This configuration supports transfer of Contacts (Business, Personal),

Memo, Schedule, To Do, and Reminder data.

• Calendar and Expense Manager data cannot be transferred.

• Contacts Untitled 1-3, Phone Book (Phone) and Phone Book (SIM) data

is transferred as Personal data.

• Memo Untitled 1-5 data is transferred as Memo data (no category).

3. Tap the Menu Bar icon to display the menu bar, and then tap System –

Data communication.

4. Tap the button next to BUSINESS NAVIGATOR to specify the data

communication configuration.

5. Tap the button next to Send.

6. Tap Set.

7. Tap the check boxes to specify the data you want to send (checked) and

the data you do not want to send (unchecked).

8. After everything is the way you want it, tap Set.

142

9. Turn on the power of the BN Unit and then press the START button on

its cradle to start the data transfer operation.

• The following shows the relationship between data when sent from the

PV Unit to a BN Unit.

Mode

Contacts

To Do

Memo

Quick-Memo

Expense

Manager

PV Unit

Untitled 1-3

Category names

Item (field) names

Phone Book

(Phone)

Phone Book

(SIM)

Category names

Due date

Untitled 1-5

Category names

BN Unit

PERSONAL

• Check Contacts (1-3) as the data

type to send this data.

Not transferred

PERSONAL

• Check Contacts (Phone) as the

data type to send this data.

PERSONAL

• Check Contacts (SIM) as the

data type to send this data.

Not transferred

Due date

MEMO

• Check Memo (1-5) as the data

type to send this data.

Not transferred

No corresponding BN Mode

Not transferred. Use the data communication software

that comes with the PV Unit to transfer this data.

143

Chapter 11 Data Communication

To receive data from the BN Unit on the PV Unit

1. Perform steps 1 through 4 under “To send data from the PV Unit to the

BN Unit”.

2. Tap the button next to Receive.

3. Tap Set.

4. Tap the check boxes next to specify the data you want to receive (checked)

and the data you do not want to receive (unchecked).

5. After everything is the way you want it, tap Set.

6. Turn on the power of the BN Unit and then press the START button on

its cradle to start the data transfer operation.

Notes

• The above procedures can be used to send or receive all data in specific

modes only. You cannot send or receive individual data items.

• Data communication can be interrupted at any time by tapping Esc.

This causes the message Stopped! to appear on the displays of both

units.

• The message Communication error! appears on the displays of both

units whenever data communication is interrupted due to cable

disconnection, line noise, or other abnormal condition.

• If the secret memory area is accessed on a unit receiving data, the received

data is stored in the secret memory area, regardless of the memory area

the data is in on the sending unit.

Autres manuels pour PV-750 Plus

Table des matières

Autres manuels Casio PDA

Casio

Casio IT-10 Series Manuel utilisateur

Casio

Casio PV-750 Plus Manuel d'instructions et de sécurité

Casio

Casio PV-100 Manuel utilisateur

Casio

Casio PV-100 Manuel utilisateur

Casio

Casio PV-750PLUS Manuel utilisateur

Casio

Casio PV-750 Plus Manuel utilisateur

Casio

Casio PV-S250 Manuel utilisateur

Casio

Casio FIVA MPC-501 Series Manuel utilisateur

Casio

Casio IT-2000W Manuel du produit

Casio

Casio SF-4300R Guide de dépannage

Casio

Casio BN-10 Manuel utilisateur

Casio

Casio NX-4000 Guide de dépannage

Casio

Casio CSF-8950 Guide de dépannage