Car-Interface CI-RL4-UCON8-LV Manuel utilisateur

Version 23.11.2020 HW: CAM(V98/(V12) CI-RL4-UCON8-LV

r.LiNK Video-inserter

CI-RL4-UCON8-LV

Compatible with

Maserati vehicles with Uconnect VP4-NA

and 8.4 inch monitor

Video-inserter for front- and rear-view camera

and two additional video sources

Product features

Video-inserter for factory-infotainment systems

1 CVBS Input for rear-view camera

1 CVBS Input for front camera

2 CVBS video-inputs for after-market devices (e.g. USB-Player, DVB-T2 tuner)

Automatic switching to rear-view camera input on engagement of the reverse gear

Automatic front camera switching after reverse gear for 10 seconds

Video-in-motion (ONLY for connected video-sources)

Video-inputs PAL and NTSC compatible

Version 23.11.2020 HW: CAM(V98/(V12) CI-RL4-UCON8-LV

Page2

Contents

1. Prior to installation

1.1. Delivery contents

1.2. Checking the compatibility of vehicle and accessories

1.3. Connectors –video interface

1.4. Settings of the 8 Dip switches (black)

1.4.1. Activating the front camera input (dip 1)

1.4.2. Enabling the interface’s video inputs (dip 2-3)

1.4.3. Rear-view camera setting (dip 5)

1.4.4. Monitor selection (dip 7-8)

1.5. Settings of the 4 Dip switches (CAN function –red)

2. Installation

2.1. Place of installation

2.1.1. Place of installation –video interface

2.1.2. Place of installation –daughter PCB

2.2. Connection schema

2.3. Installation and connection –daughter PCB

2.3.1. Warning notes concerning the installation of ribbon cables

2.4. Connection head unit –picture signal cable

2.5. Connection head-unit –Power / CAN

2.5.1. 10pin Power / CAN cable

2.5.2. 12pin interface cable

2.6. Power supply output

2.7. Connection - video sources

2.7.1. Audio-insertion

2.7.2. After-market front camera

2.7.3. After-market rear-view camera

2.7.3.1. Case 1: Video-interface receives the reverse gear signal

2.7.3.2. Case 2: Video interface does not receive the reverse gear signal

2.8. Connection video-interface –keypad

3. Interface operation

4. Picture settings

5. Specifications

6. FAQ –Trouble shooting

Version 23.11.2020 HW: CAM(V98/(V12) CI-RL4-UCON8-LV

Page3

Legal Information

By law, watching moving pictures while driving is prohibited, the driver must not be

distracted. We do not accept any liability for material damage or personal injury resulting,

directly or indirectly, from installation or operation of this product. Apart from using this

product in an unmoved vehicle, it should only be used to display fixed menus or rear-view-

camera video when the vehicle is moving (for example the MP3 menu for DVD upgrades).

Changes/updates of the vehicle’s software can cause malfunctions of the interface. Up to

one year after purchase we offer free software-updates for our interfaces. To receive a free

update, the interface has to be sent in at own cost. Wages for de-and reinstallation and

other expenditures involved with the software-updates will not be refunded.

1. Prior to installation

Read the manual prior to installation. Technical knowledge is necessary for installation. The

place of installation must be free of moisture and away from heat sources.

Before the final installation in the vehicle of the video sources, we recommend a test-run

to ensure the compatibility of vehicle and interface. Due to changes in the production of

the vehicle manufacturer there’s always a possibility of incompatibility.

1.1. Delivery contents

Take down the serial number of the interface and store this manual for support

purposes: ____________________

Version 23.11.2020 HW: CAM(V98/(V12) CI-RL4-UCON8-LV

Page4

Compatibility

Limitations

Video only The interface inserts ONLY video signals into the infotainment.

For audio inserting, use the possibly existing factory audio-AUX-input

or a FM-modulator. If 2 AV-sources shall be connected to the

infotainment, for audio switching an additional electronic part is

required.

Factory rear-view camera Automatically switching-back from inserted video to factory rear-

view camera is only possible while the reverse gear is engaged. To

delay the switch-back, an additional electronic part is required.

After market front camera The front camera will automatically be switched for 10 seconds after

disengaging the reverse gear. A manually front camera switching is

possible by external keypad.

1.2. Checking the compatibility of vehicle and accessories

Brand

Compatible vehicles

Infotainment systems

Maserati

Ghibli since model year 2017

Levante since model year 2016

and other vehicles with

Uconnect VP4-NA infotainment

with 8.4 inch monitor and capacitive

touch

Version 23.11.2020 HW: CAM(V98/(V12) CI-RL4-UCON8-LV

Page5

1.3. Connection - Video-Interface

The video-interface converts the connected after-market sources video signals into an RGB

digital signal which is inserted in the factory monitor using separate trigger options and it

reads vehicle’s digital signals out of the vehicle’s CAN-bus and converts them for the video

interface.

1.4. Settings of the 8 Dip switches (black)

Some settings have to be selected by the 8 dip-switches at the

video-interface. Dip position down is ON and position up is OFF.

See the following chapters for detailed information.

After each Dip-switch-change a power-reset of the Can-box has to be performed!

Dip

Function

ON (down)

OFF (up)

Front camera

enabled*

disabled

Power supply

output

(red wire)

+12V (max. 3A) when reverse gear

is engaged incl. 10 seconds delay

and +12V by manual switching to

front camera by keypad

+12V (max. 3A) ACC

CVBS AV1-input

enabled

disabled

CVBS AV2-input

enabled

disabled

No function

Set to OFF

Rear-view cam type

after-market

factory or none

No function

Set to OFF

Monitor selection

Try all possible combinations of dip 7 and 8 to find the

best picture (quality and size)

Version 23.11.2020 HW: CAM(V98/(V12) CI-RL4-UCON8-LV

Page6

1.4.1. Activating the front camera input (dip 1)

If set to ON, the interface switches for 10 seconds from the rear-view camera to the front

camera input after having disengaged the reverse gear. In addition, a manual switch-over to

the front camera input is possible via keypad (short press) from any image mode.

Description of the power supply output: see chapter “Power supply output”.

1.4.2. Enabling the interface’s video inputs (dip 2-3)

Only the enabled video inputs can be accessed when switching through the interface’s video

sources. It is recommended to enable only the required inputs, disabled inputs will be

skipped when switching through the video-interfaces inputs.

1.4.3. Rear-view camera setting (dip 5)

If set to OFF, the interface switches to factory picture while the reverse gear is engaged to

display factory rear-view camera.

If set to ON, the interface switches to its rear-view camera input „Camera-IN“ while the

reverse gear is engaged.

1.4.4. Monitor selection (dip 7 and 8)

Dips 7-8 customize the monitor-specific video settings which cannot be predicted as even

within the same head-unit version, the monitor specifications may vary. It is necessary to try

all possible combinations - while a working video source is connected to the chosen input of

the interface - to see which combination gives the best picture quality and size (some may

give no picture). It is possible to first hot plug through the dip combinations, but if you do

not experience any change of picture after trying all options, retry and disconnected the 6pin

power plug of the video-box between every change of the dip setting.

Note: Dips 4 und 6 are out of function and have to be set to OFF.

1.5. Settings of the 4 Dip switches (CAN function - red)

Dip position down is ON and position up is OFF.

Navigation / System

Dip 1

Dip 2

Dip 3

Dip 4

All vehicles

OFF

For all vehicles, use the OFF position of all the 4 dip switches.

After each Dip-switch-change a power-reset of the Can-box has to be performed!

Version 23.11.2020 HW: CAM(V98/(V12) CI-RL4-UCON8-LV

Page7

2. Installation

Switch off the ignition and disconnect the vehicle’s battery! The interface needs a

permanent 12V source. If -according to factory rules- a disconnection of the battery has to

be avoided, it should be sufficient to use the vehicle’s sleep-mode. In case, the sleep-mode

doesn’t succeed, the battery has to be disconnected with a resistor lead.

The Interface needs a permanent power supply! If power isn’t directly taken from the

battery, the connection’s power has to be checked for being start-up proven and

permanent.

Before a final installation, we recommend a test-run to ensure the compatibility of the

vehicle and the interface. Due to changes in the production of the vehicle manufacturer

there’s always a possibility of incompatibility.

2.1. Place of installation

2.1.1. Place of installation –video-interface

The video-interface has to be installed on the backside of the head-unit.

2.1.2. Place of installation - daugter PCB

The daughter PCB has to be installed inside the head unit.

Version 23.11.2020 HW: CAM(V98/(V12) CI-RL4-UCON8-LV

Page8

2.2. Connection schema

Version 23.11.2020 HW: CAM(V98/(V12) CI-RL4-UCON8-LV

Page9

2.3. Connections and installation –daughter PCB

Version 23.11.2020 HW: CAM(V98/(V12) CI-RL4-UCON8-LV

Page10

2.3.1. Warning notes, concerning the installation of ribbon cables

1) The contacting ends of ribbon cables always have to be installed in a straight and

precise 180° position to the connector. Each deviation from a perfect contact position will

curse faulty contact and even danger of short circuit

2) The ribbon cable’s contacting side always has to correspond to the contacting side of

the connector, concerning the mounting position.

3) Avoid cable contusion or cable injury caused by sharp-edged metal.

Table des matières

Autres manuels Car-Interface Accessoires automobiles

Car-Interface

Car-Interface CI-RL3-MIB-TT Manuel utilisateur

Car-Interface

Car-Interface CI-RL4-MZD88 Manuel utilisateur

Car-Interface

Car-Interface CI-VL2-124SPY Manuel utilisateur

Car-Interface

Car-Interface CI-RL4-UCON12 Manuel utilisateur

Car-Interface

Car-Interface CI-RL3-LR17 Manuel utilisateur

Car-Interface

Car-Interface CI-RL4-SY3-R5 Manuel utilisateur

Car-Interface

Car-Interface v.LiNK CI-VL2-LR14-OPS Manuel utilisateur

Car-Interface

Car-Interface CI-RL3-MIB-TT-LA Manuel utilisateur

Car-Interface

Car-Interface CI-RL2-MZD Manuel utilisateur

Car-Interface

Car-Interface CI-VL7-SY2 Manuel utilisateur

Car-Interface

Car-Interface CI-CARPLAY-NTG5 Manuel utilisateur

Car-Interface

Car-Interface TV-Free CI-TF-C20 Manuel utilisateur

Car-Interface

Car-Interface TV-Free CI-TF-SC14 Manuel utilisateur

Car-Interface

Car-Interface CI-RL3-CIC Manuel utilisateur

Car-Interface

Car-Interface CI-DAB-MMI2G Guide d'installation

Car-Interface

Car-Interface CI-RL4-MBN6 Manuel utilisateur

Car-Interface

Car-Interface CI-RL-PCM3-TF Manuel utilisateur

Car-Interface

Car-Interface CI-UCON7-JEEP Manuel utilisateur

Car-Interface

Car-Interface CI-RL2-MTC Manuel utilisateur

Car-Interface

Car-Interface TV-Free CI-TF-PCM21 Manuel utilisateur

Car-Interface

Car-Interface CI-RL4-MIB100 Manuel utilisateur

Car-Interface

Car-Interface CI-RL2-MBN45 Manuel utilisateur

Car-Interface

Car-Interface CI-RL4-A40 Manuel utilisateur

Car-Interface

Car-Interface CI-RL4-NAC08 Manuel utilisateur

Manuels Accessoires automobiles populaires d'autres marques

James Baroud

James Baroud Odyssey Manuel utilisateur

Motorola

Motorola i50sx Manuel utilisateur

Yakima

Yakima 9MM STANDARD BIKE MOUNT Manuel utilisateur

Feniex

Feniex T3 Manuel utilisateur

Renault

Renault 77 11 423 180 Manuel utilisateur

Kia

Kia E8300-4D000 Manuel utilisateur

Brink

Brink 756843 Manuel utilisateur

Whispbar

Whispbar K085W Manuel utilisateur

v.link

v.link CI-VL2-PC-HSD Manuel utilisateur

Viking

Viking Stack-Rack Guide de configuration rapide

Aries

Aries 203015 Manuel utilisateur

Choetech

Choetech AT0005 Manuel utilisateur

ZZ2

ZZ2 ZZAIR-PRO Manuel utilisateur

Holman

Holman 4A80L Manuel utilisateur

Thule

Thule 2075 Manuel utilisateur

Motorola

Motorola T325 Manuel utilisateur

TAUBENREUTHER

TAUBENREUTHER 16-3950 Guide d'installation

DV8

DV8 FBJL-02 Manuel utilisateur