Caple CM116 Manuel

CM116

Microwave

oven

and

rill

Caple Microwave oven and grill

Technical information

Item Part Code Description Qty

A00 251500100244 Cavity Ass'y 1

A01 252100100016 Mica plate 1

B01 261501409903 base plate 1

B02 251302000013 oven foot 4

B03 251502501540 Bottom hinge Ass'y 1

C01 251300201809 Control panel 1

C02 261505802200 Decorate on Control panel 1

C07 251306003205 Button of open door 1

C08 252010100001 button spring for open door 1

C10 251301600141 Knob 1

C14 251304900055 Display 1

C18 261400116830 PCB 1

C20

251301900386

button

CM116

- Caple Microwave oven and grill

C20

251301900386

button

C28 261516900406 Decorate on button 1

C35 261400600003 Control PCB 1

D01 251500200124 Door Ass'y 1

D02 256300500035 Latch 1

D03 252010000012 Latch spring 1

D04 251502401799 Top hinge Ass'y 1

D07 261300122204 Door frame 1

D08 256300600076 Door seal 1

D09 261505802503 Decorate for doo

E01 251200100068 Magnetron 1

E02 251202701048 THERMOSTAT 1

E04+E21 251202701535 Wire 95mm 2

E05 251200200355 H.V transforme

E06 251200701304 H.V Capacity 1

E07 251200900861 H.V diode 1

E10 256400301380 Filte

E11 261201200030 fuse 1

E13 263600500006 Lamp 1

C43 261503202100 Metal wave guide 1

E16 256201000454 Power cord 1

E28 261203300180 H.V fuse 1

E29 261201300640 THERMOSTAT 70/95 level terminal 1

E36 261201300850 THERMOSTAT 180/145 vertical terminal 1

G02 251200400025 Quarz heate

G06

261501000300

Holder of Quarz heater

G06

261501000300

Holder

Quarz

heater

L01 261301301500 Interlock holde

L02 261301101000 Interlock leve

T01 251200300001 Turntable moto

Item Part Code Description Qty

CM116

- Caple Microwave oven and grill

T02 252200100008 Couple

T03 262200200007 Ring 1

T04 252100500013 turntable 1

W01 261300800100 fan holde

W02 251300900015 fan 1

W03 261200600350 Fan moto

Z01 261501500300 Holder H.V.C 1

Z24 261502606813 Cove

-261511705802 Grill rack 1

Installation Instruction

Please Read the Manual Carefully Before Installation

Please Note

Electrical connection

The oven is fitted with a plug and must be only connected to a properly installed earthed

socket. In accordance with the appropriate regulations, the socket must only be installed and

the connecting cable must only be replaced by a qualified electrician.

If the plug is no longer accessible following installation and all-pole isolating switch must

be present on the installation side with a contact gap at least 3mm.

A. Built-in furniture

The built-in cabinet shall not have a rear wall behind the appliance.

Minimum installation height is 85cm.

Do not cover ventilation slots and air intake points.

B. Prepare the Cabinet.

1. Read the instruction on the BOTTOM CABINET TEMPLATE, put the

template on the bottom plane of cabinet.

2. Make marks on the bottom plane of cabinet according to marks “a” of the

template.

3. Remove the BOTTOM CABINET TEMPLATE, and fix the BOTTOM

BRACKETS with SCREW A.

C. Prepare the oven.

4. Fix SCREW B on the UPPER AIR TUNNEL of the oven.

D. Install the oven.

5. Install the oven into the cabinet.

zAdjust the height of SCREW B to keep 1mm gap between the SCREW B

and the top plane of cabinet.

zMake sure that the OVEN FEET are aligned with the grooves of brackets

when install the oven into the cabinet.

zDo not trap or kink the power cord.

6. Open the door; fix the oven to the cabinet with SCREW C at the

INSTALLATION HOLE of TRIM KIT.

SAFETY PRECAUTIONS

This device is to be serviced only by properly qualified service personnel.

Consult the service manual for proper service procedures to assure continued safety operation and for precautions to

be taken to avoid possible exposure to excessive microwave energy.

PRECAUTIONS TO BE OBSERVED BEFORE AND

DURING SERVICING TO AVOID POSSIBLE

EXPOSURE TO EXCESSIVE MICROWAVE ENERGY

A) Do not operate or allow the oven to be operated with the door open.

B) Make the following safety checks on all ovens to be serviced before activating the magnetron or other

microwave source, and make repairs as necessary; (1) interlock operation, (2) proper door closing, (3)

seal and sealing surfaces (arcing, wear, and other damage), (4) damage to or loosening of hinges and

latches, (5) evidence of dropping or abuse.

C) Before turning on microwave power for any service test or inspection within the microwave generating

compartments, check the magnetron, wave guide or transmission line, and cavity for proper alignment,

integrity, and connections.

D) Any defective or misadjusted components in the interlock, monitor, door seal, and microwave generation

and transmission systems shall be repaired, replaced, or adjusted by procedures described in this manual

before the oven is released to the owner.

E) A microwave leakage check should be performed on each oven prior to release to the owner.

CAUTION

MICROWAVE RADIATION

DO NOT BECOME EXPOSED TO RADIATION FROM THE MICROWAVE GENERATOR

OR OTHER PARTS CONDUCTING MICROWAVE ENERGY.

Table des matières

Autres manuels Caple Four à micro-ondes

Manuels Four à micro-ondes populaires d'autres marques

Daewoo

Daewoo KOG-574R0S Manuel utilisateur

LG MH7040SS Manuel utilisateur

Sharp

Sharp R-895(AL)M Manuel utilisateur

Dometic

Dometic DOTRM13W Manuel utilisateur

Sanyo

Sanyo EM-X680 Manuel utilisateur

Sharp

Sharp R-393M Manuel utilisateur

KitchenAid

KitchenAid KMCX4510 Instructions d'installation

Smeg

Smeg S45MCX1 Manuel utilisateur

Russell Hobbs

Russell Hobbs RHM2044 Manuel utilisateur

Sunbeam

Sunbeam SMW759 Manuel utilisateur

Gallet

Gallet FMOE230S Manuel utilisateur

Bosch

Bosch CEG732X.1B Manuel utilisateur

Dometic

Dometic Roadmate 230 Manuel utilisateur

Samsung

Samsung SJ0396W Manuel utilisateur

Sanyo

Sanyo EM-P494WS Manuel utilisateur

Sharp

Sharp R-240 Manuel utilisateur

Electrolux

Electrolux EMS2840 Manuel utilisateur

Daewoo

Daewoo KOC-984T2S13 Manuel utilisateur