Canon Pixma iP6000 Manuel utilisateur

S a v e M o n e y a n d I m p r o v e Y o u r P r i n t i n g

MIS Associates Inc 2901 Auburn Rd Auburn Hills, MI 48326 800-445-8296

http://www.inksupply.com Fax: 248-289-6013 Email: sales@inksupply.com

Canon Pixma iP6000 Installation Instructions

Installation Procedure

Canon Pixma iP6000 with MIS CFS Installed

Prerequisite -

Before starting this installation, you MUST test your printer to make sure it is printing 100

correctly. The best way to do this is to first print a Nozzle pattern, using the printer utility

software provided by Canon. Once a perfect nozzle pattern is achieved, print 5 copies of the

MIS

purge6.tif

image using the Plain Paper and Standard Quality settings on the printer. All 5

pages must print without banding or skipping (white spaces). If your printer can not do this, do

not install the CFS. Run some cleaning cycles or get new cartridges. Do not proceed until you

can pass these tests. The Purge6 image can be found on the diskette included with your

system. If you have a Mac you can download it from our website. You can also get it from the

Helpdesk Download Library.

Tools & Materials Needed -

 MIS CFS System, ink, and a working Canon iP6000 printer

S a v e M o n e y a n d I m p r o v e Y o u r P r i n t i n g

MIS Associates Inc 2901 Auburn Rd Auburn Hills, MI 48326 800-445-8296

http://www.inksupply.com Fax: 248-289-6013 Email: sales@inksupply.com

 Ruler or measuring tape

 Pair of scissors

 Alcohol and some paper towels

 Some paper to print on

Items In This Kit You ill Need To Save -

 MIS iP6000 PIXMA Installation Instructions

 Orange Cartridge Caps

 White Tube Plugs

 Vacuum Pump Kit and Instructions

If you purchased your system pre-filled, go to Step 2, else continue with Step 1.

Remove the caps from the ink bottles and replace them with the caps from the package

supplied with your CFS system.

The vacuum pump must be assembled as shown in the below photo. Check valve direction is critical.

S a v e M o n e y a n d I m p r o v e Y o u r P r i n t i n g

MIS Associates Inc 2901 Auburn Rd Auburn Hills, MI 48326 800-445-8296

http://www.inksupply.com Fax: 248-289-6013 Email: sales@inksupply.com

CARTRIDGE FILL PROCEDURE-

Before filling: If the orange caps are not installed on the cartridges, install the orange

caps that originally came with the CFS over the cartridge ink supply ports.

•

Make sure not to twist the tubing between the color cartridges and the clip on the black

cartridge as this will cause issues with filling and installation.

S a v e M o n e y a n d I m p r o v e Y o u r P r i n t i n g

MIS Associates Inc 2901 Auburn Rd Auburn Hills, MI 48326 800-445-8296

http://www.inksupply.com Fax: 248-289-6013 Email: sales@inksupply.com

•

Attach the tube from the chamber that is going to be filled to the tube adapter on the

vacuum pump.

•

Pull back on the plunger, all the way. It takes a fair amount of force.

•

Push the plunger back down to the bottom to expel air.

•

Pull back on the plunger again, all the way and push down to expel air.

•

After 3 or 4 pulls, the plunger should snap to the bottom if let go.

•

Let the vacuum pump rest for about on minute. This is a leak test.

•

After one minute, pull back on the plunger and let go. It should snap to the bottom on its

own.

•

If it does not go all the way down, then there may be a leak in one of the check valves or

the CFS cart. Do not proceed until you can pass the leak test.

•

Note, at no time does ink ever enter into the vacuum pump, only air.

With the vacuum pump fully pumped up and maximum vacuum achieved, do the following to

fill cartridge.

•

Grab the tube, about 1 inch up from the vacuum pump below the tube adapter fitting and

fold it in half or pinch it.

•

This traps the vacuum in the tube and CFS. Now remove the tube from the vacuum pump

without letting the tube unfold. Keep pinching the tube. This is important.

•

Plug the tube into the fitting on the top of the correct ink bottle for the position being

filled.

•

Release the fold in the. Ink should rush up the tube and into the cartridge.

•

The ink level in the bottle should go down about 1/2 inch or more depending on cartridge

size.

•

After about 30 seconds the cartridge will be full.

When the process is complete, fill the next chamber following the same procedure, but with a

different color. Needless to say, that if you put the wrong color ink in the wrong chamber you

will ruin the CFS cartridge, and they will need to be replaced.

After all chambers have been filled, let the cartridge sit on your bench, in its installed position,

for about 2 hours before installing into the printer. If you lose some of the ink from the lines

after they are filled, this is not a problem. As long as there is ink in the cartridge, the lines can

be full or empty, it does not matter.

When this is complete, go to Step 2.

On the printer, with the power on, open the lid to move the cartridges to the Cartridge

Replacement position. While in this position, pull the power plug out of the wall and

disconnect the USB Cable. Next, remove the cartridges. The cartridges ride in a black

cartridge carriage and are secured by a gray clamp. The clamp does not have to be lifted for

removal of the cartridges, simply push in on each cartridge tab and remove them from the

S a v e M o n e y a n d I m p r o v e Y o u r P r i n t i n g

MIS Associates Inc 2901 Auburn Rd Auburn Hills, MI 48326 800-445-8296

http://www.inksupply.com Fax: 248-289-6013 Email: sales@inksupply.com

printer.

Cartridge Carrier in Replacement Position

Remove the orange caps and any other packaging material from the CFS cartridges. Save

these orange caps as they are not available for sale separate from a CFS unit. PARTIALLY

install the CFS cartridges by placing them in their installed position but do not push the

cartridges all the way down. Make sure that the tubing between the color cartridges and the

clip on the cyan cartridge is not twisted or pinched. Do not push the cartridges all the way

down. We do not want the seals on the bottom to be push up until the tubes have been

installed in the bottles. The tubing ends with the white plugs should be aligned to the left of

the printer.

S a v e M o n e y a n d I m p r o v e Y o u r P r i n t i n g

MIS Associates Inc 2901 Auburn Rd Auburn Hills, MI 48326 800-445-8296

http://www.inksupply.com Fax: 248-289-6013 Email: sales@inksupply.com

CFS Partially Installed

Bridge Bracket and beige clip installation

S a v e M o n e y a n d I m p r o v e Y o u r P r i n t i n g

MIS Associates Inc 2901 Auburn Rd Auburn Hills, MI 48326 800-445-8296

http://www.inksupply.com Fax: 248-289-6013 Email: sales@inksupply.com

Next, clean and dry the printer housing with alcohol where the bridge bracket is to be

installed. Locate the Bridge Bracket from your package and install it as shown in the photo.

Before peeling the protective film from the double sided tape strips on the bridge bracket,

place it in the location described below and as seen in the photo below. The Bridge Bracket

mounts on the left side of the printer in such a way that the 90 degree tab on the bottom of

the Bridge Bracket is flush with the left lip of the printer and behind the tab on the printer

housing. This area should have been cleaned with an alcohol pad. Now peel the protective film

from the double sided tape strips on the bracket. See the photos below.

The tubing ends with the white plugs should now be on the left hand side of the printer. You

can now place the tubing into the beige clips on the bridge brackets, using the marks on the

tubing, and close them.

The tubes should be positioned in the right Bridge Bracket clip first. The tubing should be

marked where it will be placed in the clip. This position should allow enough length of tubing so

that the cartridge carriage can slide the full length of the printer from right to left and back

again without pulling the tubes and without being restricted by the tubes when they are

placed in the clip on the Bridge Bracket, and the tubes do not drag on the bottom of the

printer. Checking this process will be a bit difficult as the cartridges should not yet be fully

locked into the carriage.

Location of velcro strips

S a v e M o n e y a n d I m p r o v e Y o u r P r i n t i n g

MIS Associates Inc 2901 Auburn Rd Auburn Hills, MI 48326 800-445-8296

http://www.inksupply.com Fax: 248-289-6013 Email: sales@inksupply.com

Once the tubes are securely inserted into the right clip on the Bridge Bracket, you can allow

the remaining tube length to feed to the left hand beige clip, and clamp the tubing. This will

leave the remaining tube length at the left side of the printer ready to be trimmed for

connection to the bottle fittings.

Un-web the tubes from the right end beginning at the white plug up to the right hand side of

the beige clip, so that each tube can be independently on to its bottle. The tubes are easily un-

webbed by just pulling them apart, no tools are required. Don't go too far.

You can now align the bottles on the left hand side of the printer. The order of the ink bottles

from front to back are,

Magenta - Light Magenta - Yellow - Black - Cyan - Light Cyan

Installing the tubing on the bottles is easy. In the CFS kit you received a set of bottle caps

with tubes attached. Remove the caps that came on the ink bottles and replace them with the

caps that have the tubes installed. Be careful not to spill the ink.

If your system was pre-filled, cut the tubes just above the white plugs, save the plugs in a

S a v e M o n e y a n d I m p r o v e Y o u r P r i n t i n g

MIS Associates Inc 2901 Auburn Rd Auburn Hills, MI 48326 800-445-8296

http://www.inksupply.com Fax: 248-289-6013 Email: sales@inksupply.com

safe place as you may need them later if you should ever remove the CFS unit. When you clip

the tubing you Must clip it at the very edge of the white plug making sure not to lose any

length of tubing. If you ordered an empty system you should have vacuum filled your

cartridges by now, and your tubes will already be connect to the bottles.

Now push the tube onto the fitting on top of you ink bottle so the tube reaches the bottom of

the fitting. Do not put the wrong color tube on the wrong ink bottle. Follow the tube back to

the cartridge where the cartridge label identifies the ink in the chamber.

Repeat this process for each of the colors.

You can now press the cartridges down into the correct positions. You may hear them click into

place, it is okay if you do not hear the click. Just be certain they are securely seated making

certain the cartridges are properly aligned and down all the way in the carriage. Clamp the CFS

system in place by locking the gray print head clamp down. Push the cartridge carriage all the

way to the right hand inside of the printer.

Before closing the lid install the Black Foam Switch Activator into the recessed area on the

right bottom of the underside of the printer lid as shown in the photo bellow. You will need to

cut the Switch Activator to exactly 1" x 5/8" making sure to not cut it too small as it is a

friction fit. Cutting the Switch Activator too small may cause it to fall into the printer and

jam the printer carrier.

10.

Close the printer's lid ensuring the tubes are not pinched between the lid and the housing

(the Bridge Bracket is designed to hold the lid slightly open to prevent this). Plug the printer

back in and connect the USB cable, turn on the printer's power. Run a few cleaning cycles

until you have a perfect nozzle pattern. The printer is now ready for use. If you have

problems getting a perfect nozzle pattern, let the printer rest overnight, and try again in the

morning.

Note: If for any reason you must remove the CFS after installation you MUST replace the

white tube plugs as well as the orange seal caps to prevent the CFS from draining and

creating a mess.

The Care and Feeding of a CFS -

There are a couple of things you should know that will keep your system running trouble free.

Every time the Canon iP6000D CFS system is removed from the printer the prime (ink in the

tubes) will drain back to the bottles. After a few installations and removals the ink in the

S a v e M o n e y a n d I m p r o v e Y o u r P r i n t i n g

MIS Associates Inc 2901 Auburn Rd Auburn Hills, MI 48326 800-445-8296

http://www.inksupply.com Fax: 248-289-6013 Email: sales@inksupply.com

cartridge reservoirs will deplete making it necessary to Vacuum Pump Kit CFS-VP.

These systems work best if they are used frequently, daily is best, but every few days is

more important. If you are an infrequent printer or only print once or twice a week, then you

should install our AUTOPRINT (download it for free from our CFS page). Auto print will make

a printout using our Purge6 image everyday as long as you leave your computer and printer

turned on.

If you have to do cleaning cycles, do them in groups of 3 and be certain to print something,

we recommend a copy of the Purge6 pattern after every 3 cleaning cycles. The Canon

software will allow you to run cleaning cycles on the color cartridges or black cartridge

individually. If only one of the cartridges is problematic limit the cleaning cycles to include

the fewest number of cartridges possible. If you are still having problems after about 3 or 4

sets of 3 cleanings, then let the printer rest for a few hours or overnight and try again later.

This has worked on many Canon printers in the past. It gives the air bubbles in the ink a

chance to rise to the surface and get out of the printhead.

Don't let your ink bottles get empty. Refill them when they are at the 1/4 full level. Before

pouring new ink into your bottle, transfer the ink that is left into a clean glass or jar. Then

wash out the CFS ink bottle with soap and water. Then refill with leftover ink and new ink.

This keeps algae from building up on the walls of the bottle and causing premature ink failure.

An easier method is to order a spare set of empty bottles, and keep them on hand, clean and

ready to use.

For additional technical assistance please read our CFS Troubleshooting Guide or visit our

online HelpDesk.

Autres manuels pour Pixma iP6000

Autres manuels Canon Imprimante

Canon

Canon imageRUNNER ADVANCE DX C477iFZ Guide d'installation

Canon

Canon Pixma G2430 Manuel utilisateur

Canon

Canon Color imageCLASS MF8580Cdw Manuel utilisateur

Canon

Canon PIXMA TS9020 Guide de configuration

Canon

Canon PIXMA Pro9000 Mark II Series Manuel utilisateur

Canon

Canon 475D - i Color Inkjet Printer Manuel utilisateur

Canon

Canon DS700 - Selphy Compact Photo Printer Manuel utilisateur

Canon

Canon 2163B002 Manuel utilisateur

Canon

Canon LBP 2460 - B/W Laser Printer Manuel utilisateur

Canon

Canon ip3000-srm Instructions d'utilisation

Canon

Canon imageCLASS MF241d Manuel utilisateur

Canon

Canon imageRUNNER ADVANCE DX C5870i Manuel utilisateur

Canon

Canon advanced anywhere print Manuel utilisateur

Canon

Canon S820D Manuel utilisateur

Canon

Canon PIXMA PRO-1 Series Manuel utilisateur

Canon

Canon PIXMA mini320 Series Manuel

Canon

Canon LBP5050 Series Manuel utilisateur

Canon

Canon SELPHY ES3 Manuel utilisateur

Canon

Canon S630 Manuel utilisateur

Canon

Canon imagePROGRAF iPF760 Manuel utilisateur

Canon

Canon imageRUNNER ADVANCE DX 8700 Series Manuel utilisateur

Canon

Canon iP3500 - PIXMA Color Inkjet Printer Manuel utilisateur

Canon

Canon I450 - i 450 Color Inkjet Printer Manuel

Canon

Canon PIXMA G2260 Manuel utilisateur

Manuels Imprimante populaires d'autres marques

Lexmark

Lexmark 1400 Series Manuel

Evolis

Evolis Elypso Manuel utilisateur

Kyocera

Kyocera FS-9530DN Manuel utilisateur

Samsung

Samsung BIXOLON SRP-350plusF Manuel utilisateur

Dell

Dell Color Laser Printer 2130cn Manuel utilisateur

Tektronix

Tektronix Phaser 840 Manuel utilisateur

Epson

Epson ET-7750 Mode d'emploi

Eltron

Eltron P210 Guide Manuel utilisateur

Ricoh

Ricoh MD-P1 Manuel utilisateur

Epson

Epson SC-F7100 series Manuel utilisateur

Epson

Epson Stylus C40UX Manuel utilisateur

IRA3D

IRA3D POETRY4 Manuel utilisateur

Ricoh

Ricoh Aficio AP400 Manuel utilisateur

BIXOLON

BIXOLON SRP-352plusV Manuel utilisateur

Epson

Epson Stylus Photo PX700W Instructions de montage

Ricoh

Ricoh SP204SF Manuel utilisateur

Star Micronics

Star Micronics futurePRNT TSP100 Manuel utilisateur

Epson

Epson TM-TM88V-i Manuel d'utilisation et d'entretien