Canon STAPLER SORTER-L1/MS-C1 Manuel utilisateur

1998 CANON INC. CANON STAPLER SOTRER-L1 MS-C1 REV.0 NOV. 1998 PRINTED IN JAPAN (IMPRIME AU JAPON)

REVSION 0

NOV. 1998 FY8-13F9-000

STAPLER SORTER-L1

MS-C1

1998 CANON INC. CANON STAPLER SOTRER-L1 MS-C1 REV.0 NOV. 1998 PRINTED IN JAPAN (IMPRIME AU JAPON)

IMPORTANT

THIS DOCUMENTATION IS PUBLISHED BY CANON INC., JAPAN, TO SERVE AS A SOURCE

OF REFERENCE FOR WORK IN THE FIELD.

SPECIFICATIONS AND OTHER INFORMATION CONTAINED HEREIN MAY VARY SLIGHTLY

FROM ACTUAL MACHINE VALUES OR THOSE FOUND IN ADVERTISING AND OTHER

PRINTED MATTER.

ANYQUESTIONSREGARDINGINFORMATION CONTAINED HEREINSHOULD BEDIRECTED

TO THE COPIER SERVICE DEPARTMENT OF THE SALES COMPANY.

THIS DOCUMENTATION IS INTENDED FOR ALL SALES AREAS, AND MAY CONTAIN IN-

FORMATION NOT APPLICABLE TO CERTAIN AREAS.

Printed in Japan

Imprimé au Japon

Use of this manual should be strictly su-

pervised to avoid disclosure of confidential

information.

Prepared by

OFFICE IMAGING PRODUCTS TECHNICAL SUPPORT DEPARTMENT 1

OFFICE IMAGING PRODUCTS TECHNICAL SUPPORT DIVISION

CANON INC.

5-1, Hakusan, 7-chome, Toride-City, Ibaraki-Pref., 302-8501, Japan

1998 CANON INC. CANON STAPLER SOTRER-L1 MS-C1 REV.0 NOV. 1998 PRINTED IN JAPAN (IMPRIME AU JAPON)

This Service Manual provides basic facts and figures needed to service the Stapler

Sorter-L1/MS-C1 in the field and consists of the following:

Chapter 1 "General Descriptions" shows features, specifications, and names of

external parts and how to operate the sorter.

Chapter 2 "Operations and Timing" discusses the sorter's mechanical and

electrical systems by function and various timing of operation.

Chapter 3 "Mechanical System" shows how to disassemble, assemble, and

adjust the sorter.

Chapter 4 "Maintenance and Inspection" gives lists of periodically replaced parts

and consumables/ durables and a scheduled servicing chart.

Chapter 5 "Troubleshooting" shows how to troubleshoot possible faults and gives

electrical parts arrangement diagrams, LED/check pin diagrams by

PCB, and self diagnosis tables.

In addition to the above chapters, this Service Manual contains an Appendix

consisting of a general timing chart, a signals/abbreviations list, communications signals

list, a General circuit diagram controller circuit diagrams.

For installation, see the Installation Procedure that comes with the mounting kit for the

Stapler Sorter-L1 and MS-C1. (Hereafter, the Stapler Sorter-L1 will be referred to as the

"stapler sorter" and the MS-C1, "non-staple sorter.")

INTRODUCTION

1998 CANON INC. CANON STAPLER SOTRER-L1 MS-C1 REV.0 NOV. 1998 PRINTED IN JAPAN (IMPRIME AU JAPON)

The following rules apply throughout this Service Manual:

1. Each chapter contains sections explaining the purpose of specific functions and

the relationship between electrical and mechanical systems with reference to the

timing of operation.

In the diagrams, represents the path of mechanical driveÑwhere a signal

name accompanies the symbol , the arrow indicates the direction of the

electric signal.

The expression "turn on the power" means flipping on the power switch, closing

the front door, and closing the delivery unit door, which results in supplying the

machine with power.

2. In the digital circuits, '1' is used to indicate that the voltage level of a given signal is

"High," while '0' is used to indicate "Low." (The voltage value, however, differs from

circuit to circuit.)

In practically all cases, the internal mechanisms of a microprocessor cannot be

checked in the field. Therefore, the operations of the microprocessors used in the

machines are not discussed: they are explained in terms of from sensors to the

input of the DC controller PCB and from the output of the DC controller PCB to the

loads.

The descriptions in this Service Manual are subject to change without notice for

product improvement or other purposes, and major changes will be communicated in the

form of Service Information bulletins.

All service persons are expected to have a good understanding of the contents of this

Service Manual and all relevant Service Information bulletins and be able to identify and

isolate faults in the machine.

CONTENTS

CHAPTER 1 GENERAL DESCRIPTION

I. FEATURES..................................1-1

II. SPECIFICATIONS.......................1-2

III. NAMES OF PARTS.....................1-5

A. EXTERNAL VIEW .......................1-5

B. CROSS SECTION ......................1-6

IV. OPERATION................................1-7

A. OPERATION PANEL ...................1-7

B. STAPLING...................................1-8

C. RESUPPLY OF STAPLES TO

STAPLER ................................. 1-10

D. REMOVING A STAPLE JAM.... 1-12

E. REMOVING PAPER

CLOGGING.............................. 1-13

CHAPTER 2 OPERATIONS AND TIMING

I. CONSTRUCTION .......................2-1

FUNCTIONAL CONSTRUCTION .

2-1

B. ELECTRICAL CIRCUITRY .........2-2

C. SORTER CONTROLLER INPUT/

OUTPUT......................................2-3

D. COMMUNICATION BETWEEN

COPIER AND SORTER..............2-6

II. BASIC OPERATIONS .................2-7

A. OUTLINE.....................................2-7

B. BASIC OPERATIONS .................2-9

III. FEED DRIVE SYSTEM............ 2-19

A. OUTLINE.................................. 2-19

B. CONTROLLING THE FEED

SPEED ..................................... 2-21

C. OVERSTACK CONDITION ...... 2-22

D. JAM .......................................... 2-24

IV. STAPLER UNIT DRIVE

SYSTEM................................... 2-26

A. OUTLINE.................................. 2-26

B. STAPLER UNIT........................ 2-28

C. CONTROLLING THE SWINGING

MOVEMENT OF THE STAPLER

UNIT ......................................... 2-33

D. HOLDING THE PAPER............ 2-37

E. STAPLING OPERATION TIMING

(3 DOCUMENTS, NO. OF

SHEETS OF PAPER: 3) ........... 2-38

V. BIN UNIT DRIVE SYSTEM...... 2-39

A. OUTLINE.................................. 2-39

B. BIN UNIT.................................. 2-40

C. CONTROLLING THE GUIDE

BAR .......................................... 2-45

D. SENSORS INSIDE BIN UNIT .. 2-48

E. OTHER SENSORS.................. 2-49

VI. POWER SUPPLY ..................... 2-50

1998 CANON INC. CANON STAPLER SOTRER-L1 MS-C1 REV.0 NOV. 1998 PRINTED IN JAPAN (IMPRIME AU JAPON)

iii

CHAPTER 3 MECHANICAL SYSTEM

I. EXTERNALS...............................3-1

A. EXTERNAL COVERS .................3-1

II. BIN UNIT.....................................3-2

A. REMOVING THE BIN UNIT ........3-2

B. REMOVING THE BIN..................3-4

C. REMOVING THE BIN SHIFT

MOTOR (M4)...............................3-5

D. LEAD CAM..................................3-5

E. REMOVING THE GUIDE SWING

MOTOR (M3)...............................3-7

III. FEEDING GUIDE UNIT ..............3-8

A. REMOVING THE FEEDING

GUIDE UNIT ...............................3-8

B. REMOVING THE FEED

MOTOR (M2)...............................3-8

C. REMOVING THE FEED

ROLLER......................................3-9

IV. STAPLER UNIT........................ 3-10

A. REMOVING THE STAPLER

UNIT ......................................... 3-10

V. STAPLER SWING UNIT........... 3-11

A. REMOVING THE STAPLER

UNIT SWING MOTOR (M1) ..... 3-11

B. REMOVING THE STAPLER

SWING UNIT............................ 3-11

CHAPTER 4 MAINTENANCE AND INSPECTION

I. PERIODICALLY REPLACED

PARTS.........................................4-1 II. CONSUMABLES.........................4-1

III. PERIODICAL SERVICING..........4-1

CHAPTER 5 TROUBLESHOOTING

STANDARDS AND ADJUSTMENT...

5-1

A. ELECTRICAL SYSTEM ..............5-1

B. MECHANICAL SYSTEM.............5-8

II. TROUBLESHOOTING ............. 5-12

A. PROCEDURE .......................... 5-12

III. ELECTRICAL PARTS LAYOUT

DIAGRAM................................. 5-16

A. SENSORS................................ 5-16

B. MOTORS, SWITCHES, PCBS. 5-17

IV. PCB .......................................... 5-18

A. DIP SWITCH FUNCTION LIST 5-19

V. SELF DIAGNOSIS ................... 5-21

A. STACK OVER ALARM ............. 5-21

B. STAPLER ALARM.................... 5-21

C. JAM .......................................... 5-22

D. ERROR .................................... 5-23

APPENDIX

A. TIMING CHART ......................... A-1

B. SIGNAL NAME/ABBREVIATION

LIST............................................ A-5

LIST OF COMMUNICATION

DATA/SIGNAL WITH COPIER...

A-17

1998 CANON INC. CANON STAPLER SOTRER-L1 MS-C1 REV.0 NOV. 1998 PRINTED IN JAPAN (IMPRIME AU JAPON)

CHAPTER 1

GENERAL DESCRIPTION

I. FEATURES..................................1-1

II. SPECIFICATIONS.......................1-2

III. NAMES OF PARTS.....................1-5

A. External view..........................1-5

B. Cross section .........................1-6

IV. OPERATION................................1-7

A. Operation panel .....................1-7

B. Stapling ..................................1-8

C. Resupply of staples to

stapler ................................. 1-10

D. Removing a staple jam ....... 1-12

E. Removing paper clogging ... 1-13

1998 CANON INC. CANON STAPLER SOTRER-L1 MS-C1 REV.0 NOV. 1998 PRINTED IN JAPAN (IMPRIME AU JAPON)

1-1

CHAPTER 1 GENERAL DESCRIPITON

I. FEATURES

1. Light-weight, compact design

Compared with the existing 10-bin stapler sorters, an appreciable reduction has been made in

the number of parts, resulting in better stacking performance, higher reliability, and improved

serviceability.

2. High performance Stapler Unit

The use of a newly designed stapler enabled stapling as many as 30 sheets (instead of 20),

while making removal of staple jams easier.

3. Applicable to multiple types of copiers

The machine uses a straight path mechanism for its passage of paper. It also uses a DIP switch

to allow switching between new and old modes of IPC communication, supporting various types

of copiers.

CHAPTER 1 GENERAL DESCRIPITON

1-2

1998 CANON INC. CANON STAPLER SOTRER-L1 MS-C1 REV.0 NOV. 1998 PRINTED IN JAPAN (IMPRIME AU JAPON)

II. SPECIFICATIONS

Item

Types of copy paper

No. of bins

Copacity per bin: *1

equivalent to 80g/m2

Bin return time

(from 10th to 1st bin)

Bin designation function

Control panel*3

Display panel*3

Stapling*3

Copy paper size for auto

stapling*3

Spec.

Face up, bin shift and open

Plain paper: A3*2, 11"x17" ~ A5, STMT (64

~ 200g/m2)

Special paper: Tracing paper, OHP, Postcard, Label

Non sort mode:

less than 100 copies

100 copies (A4, LTR,

B5, A5, STMT, A4R,

LTRR, B5R, A3*2,

B4, LGL, 11"x17")

more than 101 copies 200 copies

(A4, LTR,

B5, A5, STMT, A4R,

LTRR, B5R)

150 copies

(A3*2, B4, LGL, 11"x17")

Sort mode: 30 Copies (A4, LTR, B5, A5,

STMT, A4R,

LTRR, B5R)

25 Copies (B4, LGL)

15 Copies (A3*2, 11"x17")

Staple sort mode*3:

30 Copies (A4, LTR, B5, A4R,

LTRR)

25 Copies (B4, LGL)

15 Copies (A3*2, 11"x17")

Group mode:20 Copies (A4, LTR, B5, A5,

STMT, A4R,

LTRR, B5R)

15 Copies

(A3*2, B4, LGL, 11"x17")

Stream sorting

30 Copies

(A4, LTR, B5, A5,

STMT, A4R, LTRR,

B5R)

25 Copies (B4, LGL)

15 Copies (A3*2, 11"x17")

Approx 10 sec.

Available (A bin may be specified (by the

host copier.))

STAPLE key

STAPLE RESUPPLY indicator, MANUAL

STAPLE indicator

Rotating cam

A3*2, A4, B4, B5, A4R, LGL, 11"x17",

LTR, LTRR

Remarks

Same as the host copier.

1st bin only

Special paper

10 copies/bin

Cascade stack

20 copies/bin

15 copies/bin

Unavailable to B5R,

STMT, A5

*1 Capacity per bin may vary depending on restrictions on the host copier.

*2 If stacking is not proper because of downward curling in staple sort mode, change the feeding

speed. (See CHAPTER 5.Dip switch function list)

*3 Stapler sorter only.

The number of sheets that may be stapled is subject to change depending on the limits imposed by the copier.

Table des matières

Autres manuels Canon Accessoires pour imprimantes

Canon

Canon imageRUNNER ADVANCE 6065 Manuel utilisateur

Canon

Canon External 2/3 Hole Puncher-B1 Manuel utilisateur

Canon

Canon BW Voice Guidance Board-A1 Manuel utilisateur

Canon

Canon AK1 Manuel utilisateur

Canon

Canon DADF-N1 Manuel utilisateur

Canon

Canon iR Security Kit-A2 Manuel d'utilisation et d'entretien

Canon

Canon Color Network UFR Printer Kit-C1 Manuel utilisateur

Canon

Canon IP 1500 Manuel utilisateur

Canon

Canon AG1 Manuel utilisateur

Canon

Canon Puncher Unit-L1 Manuel utilisateur

Canon

Canon iR1200 Series Manuel d'utilisation et d'entretien

Canon

Canon Puncher Unit-BF1 Manuel utilisateur

Canon

Canon Two-Knife Booklet Trimmer-A1 Manuel utilisateur

Canon

Canon PH-72 Manuel utilisateur

Canon

Canon Color UFRII Printer Kit-L1 Manuel d'utilisation et d'entretien

Canon

Canon PIXMA MP980 Mode d’emploi

Canon

Canon FY8-13HR-000 Manuel utilisateur

Canon

Canon Finisher-U1 Manuel de service

Canon

Canon BH-10 Manuel utilisateur

Canon

Canon DADF-J1 Manuel utilisateur

Canon

Canon Super G3 FAX Board-T1 Manuel d'utilisation et d'entretien

Canon

Canon DADF-Q1 Manuel utilisateur

Canon

Canon USB Application Interface Board-D1 Manuel utilisateur

Canon

Canon High Capacity Stacker-G1 Manuel utilisateur

Manuels Accessoires pour imprimantes populaires d'autres marques

Star Micronics

Star Micronics TSP800 Series Manuel utilisateur

REA

REA JET HR pro 2K Manuel utilisateur

HP Laserjet,Color Laserjet 4si Manuel utilisateur

oliser

oliser MS 45 Manuel utilisateur

Roland

Roland DU2-64 Instructions et recettes

Xerox

Xerox EFI EXP6000 Manuel utilisateur

Sharp

Sharp FO-1MK Manuel utilisateur

Labelmate

Labelmate PM-300 Manuel utilisateur

Epson

Epson T6248 Manuel d'utilisation

Epson

Epson OT-BZ20 Manuel utilisateur

Ricoh

Ricoh LCIT RT5100 Guide de démarrage rapide

GBC

GBC 16 Series Manuel utilisateur

Develop

Develop SD-509 Manuel utilisateur

Kyocera

Kyocera KM-6230 Manuel

Triumph Adler

Triumph Adler DF-710 Manuel

Citizen

Citizen CBM-202PC Series Manuel utilisateur

Codonics

Codonics Virtua 1VCX-LR833 Guide de référence

TonerRefillKits

TonerRefillKits ReChargX RX126 Manuel utilisateur