Campbell LP02 Manuel utilisateur

INSTRUCTION MANUAL

LP02 Pyranometer

Revision: 1/14

Campbell Scientific, Inc.

Warranty

“PRODUCTS MANUFACTURED BY CAMPBELL SCIENTIFIC, INC. are

warranted by Campbell Scientific, Inc. (“Campbell”) to be free from defects in

materials and workmanship under normal use and service for twelve (12)

months from date of shipment unless otherwise specified in the corresponding

Campbell pricelist or product manual. Products not manufactured, but that are

re-sold by Campbell, are warranted only to the limits extended by the original

manufacturer. Batteries, fine-wire thermocouples, desiccant, and other

consumables have no warranty. Campbell’s obligation under this warranty is

limited to repairing or replacing (at Campbell’s option) defective products,

which shall be the sole and exclusive remedy under this warranty. The

customer shall assume all costs of removing, reinstalling, and shipping

defective products to Campbell. Campbell will return such products by surface

carrier prepaid within the continental United States of America. To all other

locations, Campbell will return such products best way CIP (Port of Entry)

INCOTERM® 2010, prepaid. This warranty shall not apply to any products

which have been subjected to modification, misuse, neglect, improper service,

accidents of nature, or shipping damage. This warranty is in lieu of all other

warranties, expressed or implied. The warranty for installation services

performed by Campbell such as programming to customer specifications,

electrical connections to products manufactured by Campbell, and product

specific training, is part of Campbell’s product warranty. CAMPBELL

EXPRESSLY DISCLAIMS AND EXCLUDES ANY IMPLIED

WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A

PARTICULAR PURPOSE. Campbell is not liable for any special, indirect,

incidental, and/or consequential damages.”

Assistance

Products may not be returned without prior authorization. The following

contact information is for US and international customers residing in countries

served by Campbell Scientific, Inc. directly. Affiliate companies handle

repairs for customers within their territories. Please visit

www.campbellsci.com to determine which Campbell Scientific company serves

your country.

To obtain a Returned Materials Authorization (RMA), contact CAMPBELL

SCIENTIFIC, INC., phone (435) 227-9000. After an application engineer

determines the nature of the problem, an RMA number will be issued. Please

write this number clearly on the outside of the shipping container. Campbell

Scientific’s shipping address is:

CAMPBELL SCIENTIFIC, INC.

RMA#_____

815 West 1800 North

Logan, Utah 84321-1784

For all returns, the customer must fill out a “Statement of Product Cleanliness

and Decontamination” form and comply with the requirements specified in it.

The form is available from our web site at www.campbellsci.com/repair. A

completed form must be either emailed to repair@campbellsci.com or faxed to

(435) 227-9106. Campbell Scientific is unable to process any returns until we

receive this form. If the form is not received within three days of product

receipt or is incomplete, the product will be returned to the customer at the

customer’s expense. Campbell Scientific reserves the right to refuse service on

products that were exposed to contaminants that may cause health or safety

concerns for our employees.

Table of Contents

PDF viewers: These page numbers refer to the printed version of this document. Use the

PDF reader bookmarks tab for links to specific sections.

1. Introduction .................................................................1

2. Cautionary Statements...............................................1

3. Initial Inspection .........................................................1

3.1 Ships With............................................................................................1

3.2 Calibration Certificate..........................................................................1

4. Quickstart ....................................................................2

4.1 Siting Considerations ...........................................................................2

4.2 Mounting..............................................................................................2

4.3 Use SCWin to Program Datalogger and Generate Wiring Diagram ....5

5. Overview......................................................................8

6. Specifications .............................................................8

7. Operation...................................................................10

7.1 Wiring ................................................................................................10

7.2 Programming......................................................................................11

7.2.1 Input Range.................................................................................11

7.2.2 Multiplier ....................................................................................12

7.2.3 Offset ..........................................................................................12

7.2.4 Example Programs ......................................................................12

7.2.4.1 CR1000 Example Program...............................................13

7.2.4.2 CR10X Example Program................................................14

7.2.5 Output Format Considerations ....................................................15

8. Maintenance ..............................................................16

9. Troubleshooting........................................................16

Appendix

A. CM245 Adjustable Angle Mounting Stand............ A-1

A.1 Installation....................................................................................... A-1

Figures

4-1. CM225 Bracket Attached to a Crossarm..............................................2

4-2. CM225 Bracket Attached to a Mast .....................................................3

4-3. LP02 Mounting Hole............................................................................3

Table of Contents

4-4. CM225 Bracket Mounting Holes ........................................................ 4

4-5. LP02 Pyranometer Attached to CM225 Solar Sensor Mounting

Stand ................................................................................................ 4

7-1. LP02 Schematic................................................................................. 10

A-1. CM245 bracket with 2.125 in. U-bolts positioned to mount the

pyranometer horizontally on a crossarm...................................... A-1

A-2. CM245 bracket with 1.5 in. U-bolts positioned to mount

pyranometer at a 40° angle on a vertical pipe .............................. A-2

Tables

7-1. Differential Connections to Campbell Scientific Dataloggers........... 10

7-2. Single-Ended Connections to Campbell Scientific Dataloggers........ 11

7-3. Multipliers Required for Flux Density and Total Fluxes................... 12

7-4. Wiring for Example Programs........................................................... 13

LP02 Pyranometer

1. Introduction

The LP02 is an ISO-second-class pyranometer that monitors solar radiation for

the full solar spectrum range. It produces a millivolt signal that can be

measured directly by a Campbell Scientific datalogger. The LP02 can provide

solar radiation measurements for many meteorological applications. This

pyranometer is manufactured by Hukseflux.

Before using the LP02, please study:

•Section 2, Cautionary Statements

•Section 3, Initial Inspection

•Section 4, Quick Start

2. Cautionary Statements

•Although the LP02 is rugged, it is also a highly precise scientific

instrument and should be handled as such.

•Care should be taken when opening the shipping package to not damage or

cut the cable jacket. If damage to the cable is suspected, consult with a

Campbell Scientific application engineer.

3. Initial Inspection

•Upon receipt of the LP02, inspect the packaging and contents for damage.

File damage claims with the shipping company.

•The model number and cable length are printed on a label at the

connection end of the cable. Check this information against the shipping

documents to ensure the correct product and cable length are received.

•See Section 3.1, Ships With, to ensure that all of your parts are included.

3.1 Ships With

(1) Bolt for mounting from original manufacturer

(2) Nuts for mounting from original manufacturer

(1) Calibration certificate (see Section 3.2, Calibration Certificate)

(2) Bolts for mounting from original manufacturer

(1) ResourceDVD

3.2 Calibration Certificate

Included with the sensor is a calibration certificate with the sensor calibration

constant and serial number. Cross check this serial number against the serial

number on your LP02 to ensure that the given calibration constant corresponds

to your sensor.

LP02 Pyranometer

4. Quickstart

Please review Section 7, Operation, for wiring, CRBasic programming, and

Edlog programming.

4.1 Siting Considerations

The LP02 is usually installed horizontally, but can also be installed at any

angle including an inverted position. In all cases, it will measure the flux that

is incident on the surface that is parallel to the sensor surface.

Site the LP02 to allow easy access for maintenance while ideally avoiding any

obstructions above the plane of the sensing element. It is important to mount

the LP02 such that a shadow will not be cast on it at any time. If this is not

possible, try to choose a site where any obstruction over the azimuth range

between earliest sunrise and latest sunset has an elevation not exceeding 5°.

Diffuse solar radiation is less influenced by obstructions near the horizon. For

instance, an obstruction with an elevation of 5° over the whole azimuth range

of 360° decreases the downward diffuse solar radiation by only 0.8%.

4.2 Mounting

Below shows the steps for using the CM225 mounting bracket kit to mount the

LP02 to a vertical pipe (1.0 to 2.1 in. OD), or to a CM202, CM203, CM204, or

CM206 crossarm. If the sensor needs to be mounted at an angle, the CM245

Adjustable Angle Mounting Stand can be used instead (see Appendix A,

CM245 Adjustable Angle Mounting Stand).

1. Attach the CM225 to a mast or crossarm (see FIGURE 4-1 and FIGURE

4-2).

FIGURE 4-1. CM225 Bracket Attached to a Crossarm

LP02 Pyranometer

FIGURE 4-2. CM225 Bracket Attached to a Mast

2. Place the LP02 in the center of the CM225 with the cable pointing to the

nearest magnetic pole, and align the sensor’s mounting holes with two of

the bracket’s mounting holes (see FIGURE 4-3 and FIGURE 4-4).

FIGURE 4-3. LP02 Mounting Hole

Mounting Hole

LP02 Pyranometer

FIGURE 4-4. CM225 Bracket Mounting Holes

3. Place the mounting screws in the mounting holes and slightly tighten

them. The leveling screws should lightly touch the mounting plate (see

FIGURE 4-5).

FIGURE 4-5. LP02 Pyranometer Attached to CM225 Solar Sensor

Mounting Stand

4. Starting with the leveling screw nearest the bubble level, turn the leveling

screws to bring the bubble of the bubble level within the ring (see

FIGURE 4-5).

Mounting

Hole

Mounting

Hole

Mounting

Hole

Bubble Level

(3) Leveling Screws

CM225 Solar

Sensor

Mounting Stand

(2) Mounting Screws

CM200 Series

Crossarm

LP02 Pyranometer

Cable Tie

Table des matières

Autres manuels Campbell Instrument de mesure

Campbell

Campbell CS135 Manuel utilisateur

Campbell

Campbell Q-7.1 Manuel utilisateur

Campbell

Campbell LI200X Manuel utilisateur

Campbell

Campbell 27106T Manuel utilisateur

Campbell

Campbell CS110 Manuel utilisateur

Campbell

Campbell NOR 140 Manuel utilisateur

Campbell

Campbell Young 05103-LC Manuel utilisateur

Campbell

Campbell TEMPERATURE PROBE 109SS Manuel utilisateur

Campbell

Campbell HMP60 Manuel utilisateur

Campbell

Campbell CS300 Manuel utilisateur

Campbell

Campbell CS511 Manuel utilisateur

Campbell

Campbell IRGASON Manuel utilisateur

Campbell

Campbell TDR Guide de l'utilisateur

Campbell

Campbell SkyVUE 8 Manuel utilisateur

Campbell

Campbell CR1000 Manuel utilisateur

Campbell

Campbell 108 Manuel utilisateur

Campbell

Campbell 109 Manuel utilisateur

Campbell

Campbell 27106T Manuel utilisateur

Campbell

Campbell SkyVUE 8 Manuel utilisateur

Campbell

Campbell LI200X Manuel utilisateur

Campbell

Campbell CS225 Manuel utilisateur

Campbell

Campbell CR7 Manuel utilisateur

Campbell

Campbell OBS-3A Manuel utilisateur

Campbell

Campbell WindSonic Manuel utilisateur

Manuels Instrument de mesure populaires d'autres marques

Suaoki

Suaoki D40 Manuel utilisateur

Elster

Elster BK-G1.6 Manuel utilisateur

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manuel

Duratool

Duratool D03128 Manuel utilisateur

Vega

Vega VEGAPULS 65 Manuel utilisateur

Tonghui

Tonghui TH2618B Manuel utilisateur

Tenmars

Tenmars TM-801 Manuel utilisateur

MSR

MSR 145 Manuel utilisateur

TPS

TPS WP-82 Manuel utilisateur

ELMETRON

ELMETRON CP-511 Manuel utilisateur

PCB Piezotronics

PCB Piezotronics 003C30 Manuel utilisateur

Tenma

Tenma 72-10465 Manuel utilisateur

Endress+Hauser

Endress+Hauser Proline Promag 50 Caractéristiques techniques

Siemens

Siemens SITRANS F Coriolis FCT030 Manuel de la liste des pièces

KLINGER

KLINGER CMF V Series Manuel utilisateur

EXFO

EXFO FTB-2 Manuel d'exploitation et d'entretien

Keysight

Keysight M8290A Manuel utilisateur

ADTEK

ADTEK MW-5 Manuel utilisateur