Calculated Industries SCALE MASTER CLASSIC 6020 Manuel utilisateur
•Guide de
l’utilisateur
•Guía del
usuario
SCALE MASTER
®
CLASSIC v3.0
Model 6020
2 – Scale Master®Classic v3.0
Preliminary Information
Key Definitions/Functions . . . . . . . .3
Imperial/Metric Modes . . . . . . . . . . .4
Adjusting the Wheel . . . . . . . . . . . . . .5
Using the Scale Master Classic . . . . . .5
“Rolling” a Measurement . . . . . . . . . .5
Built-in Scales . . . . . . . . . . . . . . . . . . . .6
Full Reset/All Clear . . . . . . . . . . . . . .7
Changing Measurement Units . . . . .7
Using the Custom Scale/Ruler . . . . .7
Memory Function Keystrokes . . . . . .8
Programming Modes . . . . . . . . . . . . .8
Area and Volume . . . . . . . . . . . . . . . .10
Converting Between Scales . . . . . . .12
Locking Scale Settings . . . . . . . . . . .12
Using the Counter . . . . . . . . . . . . . . .13
Appendix . . . . . . . . . . . . . . . . . . . .13
Error/Auto-Range Function . . . . . .13
Interference . . . . . . . . . . . . . . . . . . . . .13
Automatic Shut-Off . . . . . . . . . . . . . .13
Battery Replacement . . . . . . . . . . . . .14
Turning the Clicker & Beep On/Off
. . . .14
Specifications . . . . . . . . . . . . . . . . . . .14
Repair and Return . . . . . . . . . . . . . .15
Warranty . . . . . . . . . . . . . . . . . . . .16
Guide de l’utilisateur (Français) . . . .19
Guía del usuario (Español) . . . . . . . .31
TABLE OF CONTENTS
3 – User’s Guide
Key Definitions/Functions
[Off/On] – Power On/Off switch
Turns power On or Off. Turning power
Off does not clear scales or modes.
[Lock] – Lock switch
Locks the mode and scale so they can-
not inadvertently be changed.
[Subtract/Count] – Subtract/Count key
Toggles measuring mode between pos-
itive and negative direction. Increases
the Count value by one. Count function
is active in the count mode.
[Rcl] – Recall key
Recalls stored values. Press [Rcl] [Rcl]
to recall the last rolled value.
[Mode] – Mode key
Used to toggle between the following
scale modes (in sequence):
1) Architectural (ARCH);
2) Engineering I (ENG I);
3) Engineering II (ENG II);
4) Custom (CUSTOM);
5) Count (COUNT).
[Scale] – Scale key
Used to toggle between various scales
within each scale mode.
[M1+] – Memory Add key (Length)
Adds the displayed value to memory.
This key is used to store a length in order
to calculate an area.
(Cont’d)
4 – Scale Master®Classic v3.0
[M2x] – Memory Add key (Width)
Adds the displayed value to memory.
This key is used to store a width in order
to calculate an area. When a length and
width have been stored in [M1+] and
[M2x], pressing [Rcl] [M2x] displays the
stored width, the next press of [M2x]
displays the area calculated from the
stored length and width, and the next
press of [M2x] displays the calculated
volume if a height has been stored.
Please see pages 10-12 for storing and
calculating an Area and Volume.
[Reset]
Used to clear the display. When pressed
together with another key, clears the
value of that key.
Imperial/Metric Modes
The Scale Master Classic is set up to use
Imperial (English) dimensional units by
default. The Scale Master Classic can be set up
to use Metric scales by using the following
sequence:
1) Turn unit off via switch.
2) Press and hold [Subtract/Count] key.
3) Turn unit on via switch.
4) Release [Subtract/Count] key.
While in Metric mode, MET will remain lit
in the scale box.
Repeat the procedure above to switch back
to Imperial mode.
(Cont’d)
5 – User’s Guide
Adjusting the Wheel
To adjust the Celcon®polymer wheel, take
a small, flat-head jeweler’s screwdriver
and slightly rotate the screw near the wheel
tip. Rotating the screw between 1 ⁄4 to 1⁄ 3
turn should adjust the wheel between free
spinning (which is too loose) to skidding
(which is too tight).
“Rolling” a Measurement
To take a measurement with the Scale
Master Classic:
1) Switch the unit on. Press [Reset] to clear
the display.
2) Select your scale mode by pressing the
[Mode] key. Then press the [Scale] key
to select your scale.
3) Begin rolling. The display will register
your measurements.
To ensure accurate measurements, be
sure to hold the unit upright and start
and stop the SMC at the exact points
you are measuring.
4) Press the appropriate key if you want
to store this measurement (ex. [M1+]
to store as length, [M2x] to store as
width).
5) Press [Reset] to clear the display and
begin a new measurement.
USING THE SCALE MASTER®CLASSIC
6 – Scale Master®Classic v3.0
Built-In Scales
Imperial (English) Units
Architect Engineer I Engineer II
ARCH ENG I ENG II
1 foot= 1 inch= 1 inch=
1/32" 10.0' 300.0'
1/16" 20.0' 333.3'
3/32" 30.0' 400.0'
1/8" 40.0' 416.6'
3/16" 50.0' 500.0'
1/4" 60.0' 583.3'
3/8" 83.3' 600.0'
1/2" 100.0' 625.0'
3/4" 166.6' 666.6'
1/1 (1") 200.0' 750.0'
3/2 (1 1/2") 250.0' 1,000.0'
2/1 (2") 1,200.0'
3/1 (3") 2,000.0'
4/1 (4") 3,000.0'
Metric Units
Architect Engineer I Engineer II
ARCH ENG I ENG II
1:1 1:100.0 1:1,000
1:2 1:125.0 1:1,250
1:3 1:150.0 1:1,500
1:4 1:200.0 1:1,625
7 – User’s Guide
1:5 1:250.0 1:2,000
1:10 1:300.0 1:2,500
1:20 1:400.0 1:5,000
1:25 1:500.0 1:6,000
1:30 1:10k
1:40 1:12.5k
1:50 1:20k
1:75 1:25k
1:50k
Full Reset/All Clear
To perform a complete reset of the unit, press
[Reset] and [Subtract/Count] simultaneously.
Changing Measurement Units
Press and hold [Subtract/Count] and press
[Mode] to switch between units. You can
also convert values from Imperial Units
(English) to Meters within the Imperial
mode. However, you cannot convert
values from Metric to Imperial when in
Metric mode.
Using the Custom Scale/Ruler
The default value (after a full reset) for
Custom Scale is one-to-one (1 foot equals
1 foot). This lets you use your Scale Master
Classic as a rolling ruler (in Feet-Inches),
which is especially useful for measuring
irregular shapes.
(Cont’d)
8 – Scale Master®Classic v3.0
1) To reset your Custom Scale setting to
a one-to-one ratio, press [Reset] and
[Subtract/Count] simultaneously.
2) Then press the [Mode] key until the
“Custom” mode appears.
3) Begin rolling.
Memory Function Keystrokes
[Rcl] [M1+] or [Rcl] [M2x]
Displays the value stored in the memory
register.
[Reset] and [M1+] simultaneously
or
[Reset] and [M2x] simultaneously
Clears the value stored in the memory
register.
[Reset] and [Rcl] simultaneously
Clears values stored in memory registers
([M1+] and [M2x]).
Programming Modes
Custom Scale
You can program and store six Custom
Scales: three in Imperial (English) mode
and three in Metric mode.
You can set a custom scale two ways:
by “rolling in” a known distance or by
entering the exact distance.
(Cont’d)
9 – User’s Guide
Rolling or Entering a Custom Scale
1) Press [Mode] until “1: CUS 1”appears
in the scale box display.
2) Press [Subtract/Count] and [Scale]
simultaneously.“
ROLL” will appear in the
main display. If you are entering a
scale, skip to step 4.
3) Roll desired dimension. “ROLLING“ now
appears in the main display.
Note: For greater accuracy, you may want to roll
the known distance several times, then enter
the distance times the number of rolls (for
example, roll a distance 5 times and if the
distance is 3 feet, enter 15 feet).
4) Press [Scale]. The display will show
zeroes and the units of measurement
annunciator will begin flashing (FT-IN for
Imperial Mode, MM for Metric Mode).
5) If you do not want to change the units
of measure, skip to step 6. If you want
to change the units of measure, press
[M1+] until you reach the desired units.
6) Press [Scale] to begin setting the scale
distance. The left-most digit will
begin flashing. Press:
[M1+] to increment this digit,
[Subtract/Count] to decrement,
[Scale] to advance to next digit,
[Mode] to move back one digit.
7) Continue to press [Scale] until all dig-
its are set and the display returns to
zero. The scale is now stored.
10 – Scale Master®Classic v3.0
Area and Volume
Finding Area
1) Roll the first dimension and press
[M1+]. A small “M” will appear in the
scale box display and the main display
will be cleared.
2) Roll the second dimension and press
[M2x]. The main display will be cleared.
3) Press [Rcl] [M2x]. This displays the linear
value stored in this register. The second
press of [M2x] will calculate and display
the area, which is the value stored in
[M1+] times the value stored in [M2x].
Finding Volume
1) Roll the first dimension and press [M1+].
2) Roll the second dimension and press
[M2x].
3) Storing a height value (if you have pre-
viously set a height, skip to step 4):
a. To Roll and Store a Height:
i. Roll the third dimension and
press [Subtract/Count] and [M2x]
simultaneously. The display will
show the rolled value and the unit
of measure will begin flashing.
ii. If you do not want to change the
unit of measure, go to step iii. To
change the unit of measure, press
[M1+] until you reach the desired
unit.
Table des matières
Langues :
Autres manuels Calculated Industries Calculatrice
Calculated Industries
Calculated Industries 3420 Manuel utilisateur
Calculated Industries
Calculated Industries PROJECTCALC CLASSIC 8503 Manuel utilisateur
Calculated Industries
Calculated Industries Measure Master Pro 4020 Manuel utilisateur
Calculated Industries
Calculated Industries 4065 Construction Master Pro v3.0 Manuel utilisateur
Calculated Industries
Calculated Industries ScheduleCalc Manuel utilisateur
Calculated Industries
Calculated Industries Pocket Handyman IV Manuel utilisateur
Calculated Industries
Calculated Industries 3423 Manuel utilisateur
Calculated Industries
Calculated Industries 4225 Manuel utilisateur
Calculated Industries
Calculated Industries 5060 Manuel utilisateur
Calculated Industries
Calculated Industries ConstructionMaster HeavyCalc 4320 Manuel utilisateur
Calculated Industries
Calculated Industries 9530 Manuel utilisateur
Calculated Industries
Calculated Industries 3420 Manuel utilisateur
Calculated Industries
Calculated Industries KitchenCalc 8300 Manuel utilisateur
Calculated Industries
Calculated Industries 3430 Manuel utilisateur
Calculated Industries
Calculated Industries GradeMatic 4000 Manuel utilisateur
Calculated Industries
Calculated Industries 8305 KitchenCalc Pro Manuel utilisateur
Calculated Industries
Calculated Industries Quilter's FabriCalc 8400 Manuel utilisateur
Calculated Industries
Calculated Industries 3442 Manuel utilisateur
Calculated Industries
Calculated Industries ProjectCalc Plus MX 8528 Manuel utilisateur
Calculated Industries
Calculated Industries Sheet Metal/HVAC Pro Calc Manuel utilisateur
