CablesPlus SCM-1 Manuel utilisateur
VIDEO MOUNT PRODUCTS
Instruction Sheet For:
SCM-1
Step 1
Before starting, lay out all parts to your mount and match them to the
parts list provided. Verify that you have all your parts before attempt-
ing to assemble the mount.
Step 2
Lay the ceiling plate onto the ceiling grid so the lips of the ceil-
ing plate rest on top of the ceiling runners. Tighten adjustable screws
to hold the plate in place. Slide the carriage into the desired
position and use the ¼” – 20UNC screws , washers , and nuts
to secure the carriage in place.
Step 3
The next steps are for those who are going to use either the near
flush pipe or 1.5” NPT pipe for installation of the mount. Those
who wish to use the mast provided with the mount proceed to step
7. Mark and cut a 2.25” hole where you desire the near flush pipe
or 1.5” NPT pipe to come down. Insert the near flush pipe or
1.5” NPT pipe through the ceiling tile and into the carriage . Use
a brake screw in the bottom threaded hole of the carriage to
secure the near flush pipe or 1.5” NPT pipe.
Step 4
Attach the desired mount to the female pipe couple , , and
. For the LCD-2537C, PM-1, PM-2, PM-3, or PM-3B this is done
with parts , , , and . Note: The mount shown in the
instructions is the PM-1. For the LCD-1C, LCD-1C w/ LCD-CM2, VMP-
042/044, or VMP046/048 this is done with parts to . Note:
The plastic washer goes on top of the desired mount as well as
inside the bottom of the female pipe couple .
Step 2: Attaching the carriage to
the ceiling plate
Step 3: Attaching the near
flush pipe or 1.5” NPT pipe to
the carriage
Step 4: Attaching the female pipe
couple to the mount
VIDEO MOUNT PRODUCTS
6
2
4
1
8
21 22
2
18
19 20
12
10
18
2
10
23 24
25 29
27
22
Step 5
Insert the turnbuckles into the ceiling plate . Make sure to use
the sets of four holes in each corner of the ceiling plate and not the
center hole on each side. If necessary use the wood screw eyebolt
or concrete anchor to provide tie wire anchor points. To
use the tie wire cut the provided wire into four equal pieces.
Then insert one piece through each turnbuckle and twist the wire at
least four times itself. Attach the other end of each piece of wire to
the eyebolts, concrete anchors, or ceiling truss again making sure
the wire is twisted around itself at least four times. Note: If the dis-
tance between the ceiling grid and wherever you’re attaching the
tie wires is longer than 3 feet then you will require more tie wire (12
gauge steel tie wire).
Step 6
Attach the escutcheon ring to the near flush pipe or 1.5”
NPT pipe. Attach the female pipe couple , , and to the
near flush pipe or 1.5” NPT pipe. Use the ¼” – 20UNC brake screw
to secure the top of the couple from turning on the near
flush pipe or 1.5” NPT pipe.
Please verify that all nuts and screws are tight.
Step 7
Attach the top of the ceiling mast (usually called the ceiling plate
in the instructions) to the adaptor plate . For the masts with a
cable channel make sure to nest the cable channel in the depres-
sion cut out in the adaptor plate. Secure the two together with 3/8”
– 16UNC screw , washers , and hex nuts .
Step 6: Attaching the female
pipe couple to the near flush
pipe or 1.5” NPT pipe
Step 7: Attaching the upper mast
to the adaptor plate
Step 5: Supporting the ceiling plate
with tie wire
3
59
15
13 1
16 21 10
14
7
22
18
17
21
10
Step 8
Placetheescutcheonringadaptor ontopoftheceilingtileand
trace around the outside of the adaptor. Then proceed to cut just
inside the circle drawn. Insert the adaptor into the hole making sure
you have a tight fit, and the wider top is on top of the ceiling tile. If
necessary widen the hole slightly to fit in the adaptor. Insert the top
of the ceiling mast through the hole in the ceiling tile. Attach the
adaptor plate to the carriage and use the ¼” – 20UNC brake
screw to secure the adaptor plate from turning.
Step 9
Insert the turnbuckles into the ceiling plate . Make sure to use
the sets of four holes in each corner of the ceiling plate and not the
center hole on each side. If necessary use the wood screw eyebolt
or concrete anchor to provide tie wire anchor points. To
use the tie wire cut the provided wire into four equal pieces.
Then insert one piece through each turnbuckle and twist the wire at
least four times itself. Attach the other end of each piece of wire to
the eyebolts, concrete anchors, or ceiling truss again making sure
the wire is twisted around itself at least four times. The ceiling plate
should be completely supported by the tie wires. Note: If the dis-
tance between the ceiling grid and wherever you’re attaching the
tie wires is longer than 3 feet then you will require more tie wire (12
gauge steel tie wire).
Step 10
Attach the lower mast and rest of the mount to the upper mast us-
ing the appropriate through bolt and nut for that mount. Attach
the escutcheon ring onto the escutcheon ring adaptor .
Please verify that all nuts and screws are securely tightened.
VIDEO MOUNT PRODUCTS
WARNING: The installer of these products must verify that the mount-
ing surface, ceiling or wall, will safely support the combined weight
of all attached equipment and hardware. Video Mount Products will
not be held liable for the improper use or installation of its products.
Enjoy Your Mount!
23
15
13
14 17
30
10
Step 10: Attaching the lower half of
the mount to the upper mast
Step 8: Attach the adaptor plate
to the carriage
Step 9: Supporting the ceiling
plate with tie wire
30
3
1
16
Autres manuels CablesPlus Support et étagère
Manuels Support et étagère populaires d'autres marques
Salamander
Salamander Acadia AC/W/L400/WH Manuel utilisateur
Fohhn
Fohhn VAT-09 Guide de l'utilisateur
ricoo
ricoo FS0522 Manuel utilisateur
AMSOIL
AMSOIL BMK-22 Guide rapide
Kargo Master
Kargo Master 48220 Manuel utilisateur
Milestone AV Technologies
Milestone AV Technologies SIMPLICITY SLF2 Manuel utilisateur
