C.A. Technologies Lynx 300C Guide de dépannage

CONVENTIONAL AIR CAP AND FLUID NOZZLE CHART

MODEL

NO. AIR CAPS

PRESS.

SIPHON

*RECOM. GUN

INLET PRESS.

FAN

CONTROL

SCFM @

MAX GUN

INLET

AI R CAP

RING

STANDARD

IN CAT

PACK

AVAILABLE FLUID

NOZZLES TIPS

NEEDLES /

marking on needle

press/siph Included 33-0608 0.8mm (.022") 40-1308C (308)

press/siph 33-0610 1.0mm (.040") 40-1310C (310)

23-2013* press/siph Included 33-0613 1.3mm (.052") 40-1313C (313)

23-2014* press/siph 33-0614 1.4mm (.055") 40-1314C (314)

23-2016* press/siph Included 33-0616 1.6mm (.063") 40-1315C (315)

Actual fluid nozzle and air cap combinations are determined by application (see application chart page 4)

*Gun inlet pressures may vary as required by application

9-10.7 23-0201

LYNX 300C

(L300C)

23-2010*

45-55 60-1500

PRESSURE/SIPHON FEED SPRAYGUN

PRODUCT INFORMATION

Lynx 300C

DISTRIBUTED BY COATING EQUIPMENT TECHNOLOGY, INC

PHONE: 586-210-0555

WEB: www.cetinc.com

Operation and Maintenance Instructions for

L300C

Spray Guns

Operation

1. Connect air supply hose at handle of gun.

2. Connect a pressurized fluid supply or paint siphon cup to the gun fluid inlet.

3.Fluidflowcan becontrolledusingthefluid controlknob,thisrestricts flowbylimitingneedle travel.Itisbest tocontrol

fluid flow byproper selection of fluid orifice size and use the fluid control knob to “fine tune flow rate”.

4. Fan width can be adjusted using the fan control knob. Turning the knob clockwise narrows the fan.

Maintenance

IMPORTANT! Routine cleaning and maintenance is essential toinsure propergun operation.

Severalstatesprohibitsprayingsolventinto theatmosphere andrequire theuse ofcovered guncleaner.

1. If a gun cleaner is being used, connect and clean the gun in the gun cleaner according to the manufactures

instructions.

2. If a gun cleaner is not being used:

Removeair cap andclean separatelyusing cleansolvent.

For pressure setups, connect a pressurized solvent supply to the fluid inlet, trigger the gun allowing solvent to flow

thru the gun until clean.

For siphon setups, first clean the siphon cup thoroughly then spray clean solvent thru the gun until clean.

NOTE: Gun head disassembly is not recommended for normal cleaning and maintenance.

Gun head disassembly and reassembly instructions:

Haverepairkit # 10-106availablebeforegundisassembly.

Gun head disassembly

Toremovethe nozzlecarrier (5) andaircap adapter (7):

1. Remove the air cap (2), fluid nozzle tip (3), fluid nozzle body(4), and needle (14).

2.Remove theneedleseal cartridge(24).

3. Loosenthe locknut (10) and remove fluid inlet(11) using a 5/8” open-endwrench.

4. The nozzle carrier (5) and air cap adapter (7) will now slide forward from the gun body (12).

Gun head reassembly

1. Install a new o-ring (8) on the air cap adapter (7).

2. Install the thread locknut (10) onto the fluid inlet (11) as far as possible.

3. Install a new fluid inlet seal (9) into the recess area on the nozzle carrier (5) inlet port.

4. Slide the nozzle carrier (5) into air cap adapter (7) and insert into the gun body (12) as far as possible. Be sure the

nozzle carrier (5) extends into the hole at the back of the gun head. Install the needle seal (24) but do not tighten.

5. Rotate the nozzle carrier (5) until the fluid inlet port in the nozzle carrier (5) is aligned with the threaded hole in the

body. While in this position, insert the fluid inlet (11) and tighten firmly.

6. Tighten the needle seal (24) to approx. 12 ft.-lb. torque.

7. Tighten the fluid inlet (11) to approx. 25 ft.-lb. torque.

8. Tighten the locknut (10) to approx. 33 ft.-lb. torque.

ITEM NO. PART NO. DESCRIPTION ITEM NO. PART NO. DESCRIPTION

1See Air Cap Chart Air Cap Retaining Ring** 16 60-205 Spring Seat*

2See Air Cap Chart Air Cap** 17 60-204 Needle Return Spring*

3See Air Cap Chart Fluid Nozzle Tip** 18 60-201 Rear Bushing

4 33-2201 Fluid Nozzle Body 19 60-119 Seal*

560-L31C Nozzle Carrier 20 60-1520 Air Valve Assembly

698-8024 Gasket* 21 60-302 Air Valve Poppet

760-32C Air Cap Adapter 22 60-125 O-Ring*

8 60-131 O-Ring* 23 61-1003 Air Valve Spring*

9 60-124 Fluid Inlet Seal* 24 60-1400 Needle Seal Cartridge*

10 60-128 Locknut 25 60-2101 Trigger

11 60-126 Fluid Inlet Fitting 26 60-1510 Air Control

12 60-1124 Lynx Gun Body Conventional 26A 60-122 Plug (optional)

13 See Air Cap Chart Fan Control Assembly** 27 60-104 Air Inlet Fitting

14 See Air Cap Chart Fluid Needle** 28 60-1033 Trigger Pivot Set

15 60-202 Fluid Control Knob 29 98-0109 Allen Plug

**See air cap selection chart on page 1

*Indicates part included in repair kit # 10-106

***

L300C CONVENTIONAL SPRAY GUN

MATERIAL TYPE FLUID ORIFICE x

AIR CAP MAXIMUM

PATTERN WIDTH PRESS. / SIPHON

Very Thin

less than 16 sec. Zahn #2

inks , dyes,

solvents, stains

Thin

16 to 20 sec. Zahn #2

lacquers, enamels,

primers, sealers

Medium

21 to 30 sec. Zahn #2

automotive base coat

enamels, primers

epoxies, urethanes

automotive clear coat

Heavy

over 30 sec. Zahn #2

heavy body primers

high solid enamels

high solid automotive coatings

adhesives

FLUID NOZZLE / AIR CAP SELECTION CHARTS

LYNX Series 300C - Pressure / Siphon Feed Guns

0.8 mm x 2010

1.0 mm x 2010 12

12 P/S

P/S

1.4 mm x 2014

1.6 mm x 2016 12

12 P/S

P/S

0.8 mm x 2010

1.0 mm x 2010

1.3 mm x 2013

P/S

1.3 mm x 2013

1.4 mm x 2014

1.6 mm x 2016

P/S

L300C CONVENTIONAL SPRAY GUN

MATERIAL TYPE FLUID ORIFICE x

AIR CAP MAXIMUM

PATTERN WIDTH PRESS. / SIPHON

Very Thin

less than 16 sec. Zahn #2

inks , dyes,

solvents, stains

Thin

16 to 20 sec. Zahn #2

lacquers, enamels,

primers, sealers

Medium

21 to 30 sec. Zahn #2

automotive base coat

enamels, primers

epoxies, urethanes

automotive clear coat

Heavy

over 30 sec. Zahn #2

heavy body primers

high solid enamels

high solid automotive coatings

adhesives

FLUID NOZZLE / AIR CAP SELECTION CHARTS

LYNX Series 300C - Pressure / Siphon Feed Guns

0.8 mm x 2010

1.0 mm x 2010 12

12 P/S

P/S

1.4 mm x 2014

1.6 mm x 2016 12

12 P/S

P/S

0.8 mm x 2010

1.0 mm x 2010

1.3 mm x 2013

P/S

1.3 mm x 2013

1.4 mm x 2014

1.6 mm x 2016

P/S

Revised12/29/15

CP-L300C-303R2 CP-L300C-PPSR2

CP-L300C

CP-L300C Smart Pack Includes:

98-0104 3/8” Socket

98-0112 Ratchet Wrench

60-8001 Gun Wrench

98-0113 Gun Cleaning Brush

Air Caps and Needles Shown on Page 1

CP-L300C-303R2 Includes:

51-303 1 QT Aluminum Pressure Cup

52-5R2 Pressure Cup Regulator

98-0104 3/8” Socket

98-0112 Ratchet Wrench

60-8001 Gun Wrench

98-0113 Gun Cleaning Brush

Air Caps and Needles Shown on Page 1

CP-L300C-PPSR2 Includes:

91-460 950 mL 3M™ PPS™ Pressure Cup

91-462 Lids and Liners (Available in 25 Pack)

91-475 #18 PPS Adapter

52-5R2 Pressure Cup Regulator

98-0104 3/8” Socket

98-0112 Ratchet Wrench

60-8001 Gun Wrench

98-0113 Gun Cleaning Brush

Air Caps and Needles Shown on Page 1

Ce manuel convient aux modèles suivants

Autres manuels C.A. Technologies Pistolet à peinture

C.A. Technologies

C.A. Technologies CPR-FE Manuel utilisateur

C.A. Technologies

C.A. Technologies Panther 100G 1590 Manuel utilisateur

C.A. Technologies

C.A. Technologies Lynx 100CVT Manuel utilisateur

C.A. Technologies

C.A. Technologies Lynx 100H Manuel utilisateur

C.A. Technologies

C.A. Technologies H2O-CPR Manuel utilisateur

C.A. Technologies

C.A. Technologies JAGUAR SLP Manuel utilisateur

C.A. Technologies

C.A. Technologies CPR Manuel utilisateur

C.A. Technologies

C.A. Technologies Lynx 100CM Manuel utilisateur

C.A. Technologies

C.A. Technologies CPR Manuel utilisateur

C.A. Technologies

C.A. Technologies Panther 200C Manuel utilisateur

C.A. Technologies

C.A. Technologies Jaguar SLP Manuel utilisateur

C.A. Technologies

C.A. Technologies Panther 200H Manuel utilisateur

C.A. Technologies

C.A. Technologies Cougar Manuel utilisateur

C.A. Technologies

C.A. Technologies H2O-CPR-G Manuel utilisateur

C.A. Technologies

C.A. Technologies FE-Line LCFM Guide de dépannage

C.A. Technologies

C.A. Technologies Techline JR Manuel utilisateur

C.A. Technologies

C.A. Technologies Lynx L200C Manuel utilisateur

C.A. Technologies

C.A. Technologies AutoCAT 100C Manuel utilisateur

C.A. Technologies

C.A. Technologies Lynx 300H Manuel utilisateur

C.A. Technologies

C.A. Technologies Tomahawk TG Manuel utilisateur

C.A. Technologies

C.A. Technologies Tomcat Series Manuel utilisateur

C.A. Technologies

C.A. Technologies AutoCAT 100CVT Manuel utilisateur

C.A. Technologies

C.A. Technologies Jaguar 300H Manuel utilisateur

C.A. Technologies

C.A. Technologies AutoCAT 300C Manuel utilisateur

Manuels Pistolet à peinture populaires d'autres marques

SNOWJOE

SNOWJOE Sunjoe 24V-GS-LTW-RM Manuel utilisateur

Graco

Graco 246737 Manuel d'utilisation et d'entretien

Binks

Binks SV100 Manuel utilisateur

Fimco

Fimco LG-4-3-1 Manuel utilisateur

AG SPRAY

AG SPRAY FS-ATV-25BL Manuel utilisateur

Nordson

Nordson MicroMax 2 Manuel utilisateur

Bonide

Bonide 051 Manuel d'utilisation

zogics

zogics Z-DAS Manuel utilisateur

KISANKRAFT

KISANKRAFT KK-KBS-165 Manuel utilisateur

Matrix

Matrix SG 650 Manuel utilisateur

Anest Iwata

Anest Iwata SGA-3 Guide de démarrage rapide

paasche

paasche VV Fiche technique

Carlisle

Carlisle DeVilbiss JGA-510 Manuel utilisateur

Gardena

Gardena 11120 Manuel utilisateur

Conrad

Conrad Hobby Airbrush K3 Manuel utilisateur

wiwa

wiwa 14025 R/F Manuel utilisateur

Graco

Graco EM 390 Manuel d'utilisation

DeVilbiss

DeVilbiss LUNA2i Manuel utilisateur