C.A. Technologies FE-Line LCFM Guide de dépannage

HVLP AIR CAP AND FLUID NOZZLE CHART

MODEL

NO. AIR CAPS Press /

Siphon

*MAX GUN

INLET PRESS.

FOR HVLP

FAN

CONTROL

SCFM @

MAX GUN

INLET

AI R CAP

RING

STANDARD

IN CAT

PACK

AVAILABLE FLUID

NOZZLES TIPS

NEEDLES /

marking on needle

31-0205 0.5mm (.020")

Included 31-0208 0.8mm (.022")

21-1090 pressure 15 6 31-0210 1.0mm (.040")

21-1091 pressure 15 8 31-0212 1.2mm (.046")

21-1092 pressure 15 8 Included 31-0213 1.3mm (.052")

21-1093 pressure 18 10 31-0214 1.4mm (.055")

21-1094 pressure 33 13 31-0215 1.5mm (.059")

31-0216 1.6mm (.063")

Included 31-0217 1.7mm (.070")

*Note: Air cap test gages are available to confirm HVLP compliance.

Actual fluid nozzle and air cap combinations are determined by application (see application chart page 4)

*Gun inlet pressures may vary as required by application

40-1801 (1801)

FE-LINE

LOW CFM

(FELCFM)

60-1317 21-1001

FE-Line LCFM

PRESSURE FEED SPRAYGUN

PRODUCT INFORMATION

DISTRIBUTED BY COATING EQUIPMENT TECHNOLOGY, INC

PHONE: 586-210-0555

WEB: www.cetinc.com

Operation and Maintenance Instructions for FE-LCFM Spray Guns

Operation

1. Connect air supply hose at handle of gun.

2. Connect a pressurized fluid supply to the gun fluid inlet.

3.Fluidflowcan be controlledusingthe fluidcontrolknob, thisrestrictsflowbylimitingneedletravel.It isbestto control

fluid flow byproper selection of fluid orifice size and use the fluid control knob to “fine tune flow rate”.

4. Fan width can be adjusted using the fan control knob. Turning the knob clockwise narrows the fan.

Maintenance

IMPORTANT! Routine cleaning and maintenanceis essential toinsure proper gun operation.

Severalstates prohibitsprayingsolvent into theatmosphere andrequirethe use ofcoveredgun cleaner.

1. If a gun cleaner is being used, connect and clean the gun in the gun cleaner according to the manufactures

instructions.

2. If a gun cleaner is not being used:

Removeair capand cleanseparatelyusing clean solvent.

For pressure setups, connect a pressurized solvent supply to the fluid inlet, trigger the gun allowing solvent to flow

thru the gun until clean.

NOTE:Gun head disassemblyis not recommended for normal cleaning and maintenance.

Not recommended to soak entire spray gun in solvent.

Gun head disassembly and reassembly instructions:

Haverepairkit #10-140availablebeforegundisassembly.

Disassembly

1.Remove thetrigger byremovingbothscrews (19).

2.Removefluidcontrolknob(11).

3.Removeneedlereturnspring(13)and needle(12).

4. Removeair valve assembly(9) using a9/16”wrench.

5.Using a7/16”wrench remove the needlesealcartridge (20).

6. Using a 13 mm wrench remove the side port control (10) and air control (15).

7. Using a 11/16” wrench loosen locknut (18), using a 5/8” wrench remove fluid inlet (17).

8. Remove air cap (1 & 2), remove fluid tip (3) using a 3/8” socket.

9.Using a 1”wrench remove headinsert(4).

Reassembly

1. Install a new o-ring (7 and 8) on air valve assembly, lightly lubricate o-rings with vasoline and reinstall airvalve (9) into

the gun body(6).

2.Installa newseal(5) ingunbody(6).Reinstallheadinsertintogunbodyandtighten.Reinstallfluidtip(3)and tighten.

3. Install new seal (5) in gun body. Reinstall and tighten fluid inlet (17). Tighten locknut (18) after fluid inlet has been

tightened.

4.Remove theshipping pinfrom anew needleseal cartridge(20). Installnewneedleseal cartridge(20).

5. Reinstall side port control (10) and air control (15).

6.Reinstallneedle(12), needlereturn spring (13)and fluid controlknob (11).

7. Reinstall air cap (1 & 2).

ITEM NO. PART NO. DESCRIPTION ITEM NO. PART NO. DESCRIPTION

1See Air Cap Chart Air Cap Ring** 11 60-1312 Fluid Control Knob

2See Air Cap Chart Air Cap** 12 See Air Cap Chart Fluid Needle**

3See Air Cap Chart Fluid Nozzle Tip** 13 60-211 Needle Return Spring*

460-36 Head Insert 14 60-104 Air Inlet Fitting

560-137 O-Ring* 15 60-1319 Air Control

6 60-1301-BL Gun Handle 16 60-2111 Trigger

7 98-5125 O-Ring* 17 60-126 Fluid Inlet

898-5225 O-Ring* 18 60-128 Locknut

9 60-1320 Air Valve Assembly 19 60-1315 Trigger Pivot Set (2)

10 60-1317 Side Port Control 20 60-1329 Needle Seal Cartridge*

**See air cap selection chart on page 1

*Indicates part included in repair kit # 10-140

HVLP AIRCAP TEST GAGES

21-1090-G

21-1092-G

21-1093-G

FOR

FELCFM

GUNS 21-1094-G

FE-LCFM HVLP SPRAY GUN

MATERIAL TYPE FLUID ORIFICE x

AIR CAP MAXIMUM

PATTERN WIDTH CFM

Very Thin

less than 16 sec. Zahn #2

inks , dyes,

solvents, stains

Thin

16 to 20 sec. Zahn #2

lacquers, enamels,

primers, sealers

Medium

21 to 30 sec. Zahn #2

automotive base coat

enamels, primers

epoxies, urethanes

automotive clear coat

Heavy

over 30 sec. Zahn #2

heavy body primers

high solid enamels

high solid automotive coatings

adhesives

*LCFMindicates air caps that require low cubic feet per minute air volume and can be operated with a 1.5 HPcompressor.

1.3, 1.4, 1.5 mm x 1090 (LCFM)

1.3, 1.4, 1.5 mm x 1091 (LCFM)

1.3, 1.4, 1.5 mm x 1092 (LCFM)

1.3, 1.4, 1.5 mm x 1093

1.3, 1.4, 1.5 mm x 1094

1.6, 1.7 mm x 1094 12 13

1.0, 1.2 mm x 1091 (LCFM)

1.0, 1.2 mm x 1092 (LCFM)

1.0, 1.2 mm x 1093

FLUID NOZZLE / AIR CAP SELECTION CHARTS

FE-LCFM Series - Pressure Feed Guns

0.5, 0.8 mm x 1090 (LCFM)

0.5, 0.8 mm x 1091 (LCFM)

0.5, 0.8 mm x 1092 (LCFM)

Revised12/23/15

CP-FELCFM-303R2 CP-FELCFM-PPSR2

CP-FELCFM

CP-FELCFM Smart Pack Includes:

98-0104 3/8” Socket

98-0112 Ratchet Wrench

60-8001 Gun Wrench

98-0113 Gun Cleaning Brush

Air Caps and Needles Shown on Page 1

CP-FELCFM-303R2 Includes:

51-303 1 QT Aluminum Pressure Cup

52-5R2 Pressure Cup Regulator

98-0104 3/8” Socket

98-0112 Ratchet Wrench

60-8001 Gun Wrench

98-0113 Gun Cleaning Brush

Air Caps and Needles Shown on Page 1

CP-FELCFM-PPSR2 Includes:

91-460 950 mL 3M™ PPS™ Pressure Cup

91-462 Lids and Liners (Available in 25 Pack)

91-475 #18 PPS Adapter

52-5R2 Pressure Cup Regulator

98-0104 3/8” Socket

98-0112 Ratchet Wrench

60-8001 Gun Wrench

98-0113 Gun Cleaning Brush

Air Caps and Needles Shown on Page 1

Ce manuel convient aux modèles suivants

Autres manuels C.A. Technologies Pistolet à peinture

C.A. Technologies

C.A. Technologies Lynx 100H Manuel utilisateur

C.A. Technologies

C.A. Technologies Panther 100G Manuel utilisateur

C.A. Technologies

C.A. Technologies Tomahawk TG Manuel utilisateur

C.A. Technologies

C.A. Technologies CAT-Xpress Guide de dépannage

C.A. Technologies

C.A. Technologies FE-Line Fine Finish Manuel utilisateur

C.A. Technologies

C.A. Technologies Lynx 300C Guide de dépannage

C.A. Technologies

C.A. Technologies Jaguar SLP Manuel utilisateur

C.A. Technologies

C.A. Technologies Panther 100G 1590 Manuel utilisateur

C.A. Technologies

C.A. Technologies CPR Manuel utilisateur

C.A. Technologies

C.A. Technologies TOMCAT 100C Guide de dépannage

C.A. Technologies

C.A. Technologies Lynx 300H Manuel utilisateur

C.A. Technologies

C.A. Technologies AutoCAT 100C Manuel utilisateur

C.A. Technologies

C.A. Technologies Cougar Manuel utilisateur

C.A. Technologies

C.A. Technologies JAGUAR SLP Manuel utilisateur

C.A. Technologies

C.A. Technologies Jaguar 300H Manuel utilisateur

C.A. Technologies

C.A. Technologies H2O-CPR-G Manuel utilisateur

C.A. Technologies

C.A. Technologies AutoCAT 100CVT Manuel utilisateur

C.A. Technologies

C.A. Technologies Techline JR Manuel utilisateur

C.A. Technologies

C.A. Technologies Lynx L200C Manuel utilisateur

C.A. Technologies

C.A. Technologies Lynx 100 Series Manuel utilisateur

C.A. Technologies

C.A. Technologies LYNX L100CM Manuel

C.A. Technologies

C.A. Technologies H2O-CPR Manuel utilisateur

C.A. Technologies

C.A. Technologies Panther 200C Manuel utilisateur

C.A. Technologies

C.A. Technologies Jaguar 300 Series Manuel utilisateur

Manuels Pistolet à peinture populaires d'autres marques

SNOWJOE

SNOWJOE Sunjoe 24V-GS-LTW-RM Manuel utilisateur

Graco

Graco 246737 Manuel d'utilisation et d'entretien

Binks

Binks SV100 Manuel utilisateur

Fimco

Fimco LG-4-3-1 Manuel utilisateur

AG SPRAY

AG SPRAY FS-ATV-25BL Manuel utilisateur

Nordson

Nordson MicroMax 2 Manuel utilisateur

Bonide

Bonide 051 Manuel d'utilisation

zogics

zogics Z-DAS Manuel utilisateur

KISANKRAFT

KISANKRAFT KK-KBS-165 Manuel utilisateur

Matrix

Matrix SG 650 Manuel utilisateur

Anest Iwata

Anest Iwata SGA-3 Guide de démarrage rapide

paasche

paasche VV Fiche technique

Carlisle

Carlisle DeVilbiss JGA-510 Manuel utilisateur

Gardena

Gardena 11120 Manuel utilisateur

Conrad

Conrad Hobby Airbrush K3 Manuel utilisateur

wiwa

wiwa 14025 R/F Manuel utilisateur

Graco

Graco EM 390 Manuel d'utilisation

DeVilbiss

DeVilbiss LUNA2i Manuel utilisateur