BRIGHT CB460 Series Manuel utilisateur

- 1 -

WHEEL BALANCER

MODEL

：

CB460

- 2 -

This instruction manual has been prepared especially for you.

The manner in which you care for and maintain your banlancer

will have a direct effect on its overall performance and longevity.

READ THIS ENTIRE MANUAL

BEFORE OPERATION BEGINS.

RECORD HERE THE FOLLOWING INFORMATION

WHICH IS LOCATED ON THE SERIAL NUMBER DATA PLATE

SERIAL No.：

MODEL No.:

MANUFACTURING DATE:

Warranty Item

The machine include the operation system, tooling and accessories will be under warranty for one

year.Afer the confirmation of eliminate improper damage and unreasonable use. During this time,

the manufacturer will repair or change the return parts or machine from the customers. The charge

will be paid by the manufacturer. But the manufacturer will not have the responsibility for the

normal wear and tear, improper use or transport, or lack of maintenance. The manufacturer will

not inform the customer when the products improved or production line rebuild, the difference rise

from this is not include in this warranty. All the change of this warranty item will be according to

the machine’s model and serial number, all the complain must be provide the machine’s model and

serial number.

- 3 -

INDEX

1. The brief description of wheel balancer

1) Working scope

2）Instructions for the stickers (include the warning sticker)

3）Appearance of wheel balancer

4）Performance and feature

5）TechnicalData

2. The use of wheel balancer

1) Precaution in transport the machine

2）Demand for install the electrical device

3）Air supply connection

4)Precaution in installation and operation

5)Call your attention to the followingproblems

6)The Brief Controlling Panel

3. The Brief Description Controlling Panel

4.Basic operation of balance detector and selection of functions

5.Self-calibration

6.Selectionoffunctions

4. Code in computer self-diagnosis

5. Wheel Shaft Counter positioning

6. Standard accessories of Tire Balance Detector

7. Code in Computer Self-diagnosis

8. Wheel Shaft Counter positioning

9. Standard accessories of Tire Balance Detector

10.Trouble shooting

11.Presettingthestored3itemsdata

12. Use for grease

12.1 Grease the balancer

12.2 Safety data list for use of grease for balancer

13.TheDrawingOfPowerBoard

- 4 -

14.TheDrawingOfComputerBoard

15.Electrical diagram

16．Spare part list

1. THE BRIEF OF WHEEL BALANCER

1）Working scope

This microcomputer control, digital display, high-performance

balancer can balance car tyre, small passenger car tyre and light

truck tyre, also it designed for balancing super truck and

passenger car tyre, that up to 105kg. also it can balance special

shape tyre for aluminum alloy tyre.

2）Instructions for the stickers (include the warning sticker)

Ⅰ、Nameplate

The nameplate place on the back of the machine, on the upright side of the machine body,

the meaning for every part is as below:

A、CB460

model

B、Serial number

The first three figure is the model, the fourth to seventh figure is for manufacture date,

and the last four figure is for serial number for the machine

Ⅱ、Lightning mark

This sticker place on the back of the machine, show where to put in the

Power wire and call the attention for the safety for the user.

Ⅲ、Warning for the rotating part of the machine

this sticker place near the balancing shaft, to remind the user that this part

is the rotate part, belong to the dangerous part, not touch it by hand, the

arrow also show the direction for the rotating.

Ⅳ、Ground mark

this sticker place on the left side of the back of the machine, to show where

to connect the ground wire.

- 5 -

Ⅵ、、The original data

this mark is under the nameplate on the back of the machine body,

or on the front or left side for the inside machine body. (some

machine only put them inside the body). These three data is input

before the delivery after the calibration (save in the CMOS chip ),

that is for the reference for the user later.

3）Appearance of wheel balancer

4) Performance and feather

*The machine adapt the center computer system of import parts, high intelligence, high

duration.

*Main shaft use importing bearing, low noise, high precision.

*Advanced computer driving system.

*Automatic calibration function of static and dynamic.

*Three ALU program.

*Self calibration and Self-diagnosis

5）Technical Data

NO Item Technical data Note

1 Kind for rim Alu, steel and alloy rim

- 6 -

2 Balancing class

car、light truck、Super truck and passenger

tyre

3 Balancing mode Dynamic, static, and three ALU

4 Driven style Driven by electrical

5 Power supply demand 230V 50Hz

6 Style for put the weight Standard

Suit for different

style

Measure for inside and

outside

Standard Suit for every model

The machine start when

low down the cover

Semi-automatic

low down the

cover,and press

the START button

9 Quick handle nut Standard

10 Caliper/weight/handle Standard

Change for millimeter and

inch

Standard

Change for gram and

ounce

Standard

13 Calibration Standard

Self- diagnose /show

Err-

Standard

15 Wheel lifter Used for truck tyre

Car balancer not

use this

16 Brake Automatic/Manual

17 Brake Automatic/Manual Brake

18 Display cover Packed separately

19 Display panel LBD

20 Distance setting Manual

21 Cone 5

22 Balancing time 7s（16″standard rim）

Relative to wheel

weight

23 Max. balancing speed 230r/min

Relative to wheel

weight

24 Balancing precision ≤3g

25 Max.wheel width 20″

- 7 -

26 Max.wheel diameter 47″

27 Max.rim diameter 10″~24″

28 Max.rim width 1．5″~20″

29 Max.wheel weight 150kg

30 Dimension（after packing）1320X950X1180（LXWXH）

31 Machine weight 274kg Include wheel lifter

32 Temperature 0~40℃

33 Hmidity ≤75%

34 Noise ≤70dB

35 Resistance ≥20MΩ

36 Power About 800W

2. The use of wheel balancer

1) Precaution in transport the machine

A、Be careful when transport and unpack the machine, to avoid the damage of the machine.

B、Check if the machine is damage or not during the transport, and make the record for the

problem, then show them to the carrier, and make the record on the document.

C、Check the structure for the machine, to see if the data on the machine’s nameplate and

motor’s nameplate is the same as demand, if have doubt,

Reflect it quick, so that can make the resolution for this in time.

D、All the work about electricity and adjustment must be operated by the authorized person.

2）Demand for install the electrical device

A、 Demand for the electrical wire. Before the install, make sure the power supply is the

same as the machine demand，the wire of the machine can not connect with the

power supply directly, a breaker should be used, to avoid the damage of the machine

when the power is not stable, normally, a 15A breaker (with overload protect and less

load cut off) is recommended, if a bigger breaker is used, the fuse should be installed,

the lead wire area

can not less than 1.5mm2

（earth wire can 1.0mm2）,oil-against cable can be used, （built on

stilts or insert into hose），or monolayer insulate wire can be used through wire groove or

- 8 -

pipeline. If the working site is not good, much equipment, vehicle and people go through,

the wire should be built on stilts or cover up.

B、Demand for the power supply. The voltage should be stable, the wire should have overload

ability，fluctuate of the voltage should not exceed the rated voltage 10%，fluctuate of the

frequency should not exceed 1Hz，or the regulator should be mounted, to keep the voltage

and frequency stable.

C、Demand for the socket. The car balancer is equipped with the wire and plug before delivery,

the operator can only choose the socket according to the plug, but the socket must apply for

the following demand:

the rated capacity should more than 500VAⅠ，rated current more than 15A；

the socket must have reliable earth wire, the socket with only two clamp can not beⅡ

used，or it will affect the precision of the balancer and ability of anti-jamming.

Ⅲit better with the switch，if there is something wrong with the wire, can cut off the

electricity or it will damage the machine

ⅣThe plug should connect well with the socket.

ⅤIt is better use the special socket, do not use many equipment on the same socket.

3）Air connection

A、Wheel lifter technical data：

Working range：0.1~0.8MPa（0.5~0.8Mpa in normal working ）

Precision：0.01MPa

Air supply：this machine is not equipped air supply, the customer need to equip the air

supply themselves, it should be control within0.6~0.9Mpa, then adjust to below 0.8Mpa

by the valve on the lifter, the air supply should have filter, the precision should 5μm ;

medium flux >0.15m3/min, temperate 5~60 . The lifter equipped with quick union, Φ8℃

- 9 -

(inside) hose should be used to connect with the air supply, then tighten it by caliper.

Working condition: according to the demand for the balancer

Net weight:50Kg

Dimension:1129×1190×728mm （LXWXH）

B、Unit conversion

1Mpa=l0Bar

1Bar=14.5Psi

1Bar≈1Kg/cm2

B、Pneumatic

diagram(right)

4）Precaution in

installation and operation

*Don't place the detector in an extreme hot or cold condition, and avoid setting the

machine close to the heating radiator, tap, air humidifier and stoves.

*Don't place the detector near the window under the direct sunshine .In case of inevitable,

the window curtain, shield and hood should be used to shade the detector.

*No contact of the machine is allowed with dust, ammonium, alcohol, diluents and

pulverized adhesive, etc.

*The detector should be installed on a leveled ground.

*Never place it close to the air compressor or any substance that may generate vibration.

*During the operation don't close to the detector unless the operator.

*The dynamic balance detector should use separated power(230V) socket. Don’t connect

any other wire in this socket. Attention must be paid to the reliable grounding, if there is

no grounding connection in the socket, it must be added before connect with the power

- 10 -

source.

*The wire line of dynamic balance detector should be prevented from stepping on.

*Contact with the special service man for maintenance before you have to move the

dynamic balance detector.

** At least 80cm should be left at the back of the machine, 50 cm on the left side of the

machine should be left, to ensure the aeration ,disperse and the normal work, 200 cm on

the right side of the machine should be left, to facility the mount and demount the tyre or

mounting the lifting device.

*The lifting device should be used when the tyre is more than 15kg, not use hand to lift

tyre directly, to avoid the injury of the operator.

* Fix the machine on the ground by bolt before operate the machine, (fix three points),or

the result may not correct due to the shake of the machine, especially when the tyre

more than 35kgs.

*The machine equipped with the protection cover and the switch, the motor automatically

start when the cover low down, and will stop when lift up the cover, in order to ensure

your safety, do not demount the cover.

*The operator should wear the clothes –fitting, tighten the button, wear the thin gloves,

the thick gloves will affect the operation, do not wear sandal, it is better to wear insulated

shoes.

* Around the balancer, there should be no other electrical equipment, or the machine

≥50cm

≥80cm

≥200cm

Autres manuels pour CB460 Series

Table des matières

Autres manuels BRIGHT équilibreuse de roues

BRIGHT

BRIGHT OSPREY BP63 Manuel utilisateur

BRIGHT

BRIGHT VULTURE BP46 Manuel utilisateur

BRIGHT

BRIGHT CB460 Series Manuel utilisateur

Manuels équilibreuse de roues populaires d'autres marques

Corghi

Corghi PROLINE 640 Manuel utilisateur

IDEAL

IDEAL IWA-60-1500-K Manuel utilisateur

Snap-On

Snap-On WBM250 Manuel utilisateur

Atlas Equipment

Atlas Equipment WB55 Manuel utilisateur

Urrea

Urrea BAL24A Manuel utilisateur

Mondolfo Ferro

Mondolfo Ferro MT 2450 Manuel d'utilisation

Hofmann

Hofmann geodyna 6900-2p Manuel utilisateur

CEMB

CEMB K22 Manuel utilisateur

Hofmann

Hofmann POWER CLAMP features Manuel d'utilisation

Desoutter

Desoutter Industrial Tools DU Series Manuel utilisateur

HPA-Faip

HPA-Faip B 235 Evo Manuel utilisateur

Hofmann

Hofmann megaspin 300 Mode d’emploi

Bonica

Bonica BC988 Manuel utilisateur

Snap-On

Snap-On EEWB304B Manuel utilisateur

Dannmar

Dannmar DB-70 Manuel utilisateur

Mountz

Mountz MZ-3A Manuel utilisateur

John Bean

John Bean VPI System Manuel utilisateur

PREVOST

PREVOST BAL 250300F Manuel utilisateur