Brecknell S100 Manuel utilisateur
Model S100
Electronic Bench Scale
User Manual
WARNINGS
Safe installation
Safety
THE EQUIPMENT CONTAINS NO USER SERVICEABLE COMPONENTS.
Installation and maintenance of the equipment must only be carried out by trained and
authorised personnel.
Electrical installation
The mains lead must be connected to a supply outlet with a protective earth contact. The
electrical supply at the socket outlet must provide over current protection of an appropriate
rating.
For your protection all mains (110V or 230V) equipment used out of doors or in wet or damp
conditions should be supplied from a correctly fused source and protected by an approved
ground fault protection device (RCD, GFCI etc.)
IF IN DOUBT SEEK ADVICE FROM A QUALIFIED ELECTRICIAN.
Routine maintenance
To avoid the possibility of electric shock or damage to the machine, always switch off the
machine and isolate from the power supply before carrying out any routine maintenance.
To avoid the risk of the machine falling, where applicable, ensure that it is placed securely on a
flat and level surface.
Safe use
Caution – Cleaning the indicator/weigh head
Harsh abrasives, solvents, scouring cleaners and alkaline cleaning solutions, such as washing
soda, should not be used especially on the display windows. Under no circumstances should
you attempt to wipe the inside of the machine.
The outside of standard products may be wiped down with a clean cloth, moistened with water
containing a small amount of washing up liquid.
The outside of products waterproofed to IP65, IP66 and IP67 may be washed down with water
containing a small amount of proprietary detergent.
Training
Do not attempt to carry out any procedure on a machine unless you have received the
appropriate training or read the Instruction Manual.
EMC compliance
The following may be applicable to your machine.
WARNING:
This is a class A product. In a domestic environment this product may cause radio interference
in which case the user may be required to take adequate measures.
Product Contents
Indicator
Base
Steel Pipe
Pipe Bracket
Pipe Bracket
Screws x 4
Nuts x4
Platform
Allan keys
Indicator Assembly
1. Feed the loadcell wire
through the base and the
pipe.
2. Insert the pipe into the
base
3. Tighten the nuts with
the provided.allen key
4. Feed the loadcell
wire through the
bracket.
5. Insert the pipe into
pipe bracket.
6. Tighten the screw
7. Set the indicator on the
bracket and use the four
nuts (provided) to fix the
indicator in place.
8. The indicator stand is now
fully assembled.
Platform Assembly
Remove the four packaging pads from the base of the
platform before use
Securely fix the indicator stand onto the side of the
platform using the two nuts. The scale is now
ready for use.
Setting the Scale Up for Use
Display and Keypad
ON/OFF TAREZERO UNITS
I0Tkg/lb
kg lb Zero Low Batt CH Net
0-+
SBI 100
Max 300kg
d = 0.05kg
ON/OFF
Function Keys Annunicators
Tare
ZERO
0
Illuminated when the weight is zero
On/Off
k
g
l
b
Depends on active unit of measure
(Flashing LED means that the weight
reading is not stable.)
Units
NET
Illuminated when adapter is plugged
in.
Zero
CH
Illuminated when the battery is
charging.
Manual symbols
Short key press Long key pressMultiple key press
Scale Operation
Turning On and Zeroing the Scale
1.
ZERO
0
1.
ZERO
0
Turning off the scale
Selecting Unit of Measure
kg lb
Using the Tare
1.
2.
NET
3.
NET
4.
NET
k
g
g
oz lb
Removing the Tare
ZERO
0
Setting up the Auto-Off Function
Scale must be switched on.
1.
2. 0-9 minutes (0 switches the function off).
3.
ZERO
0
Calibration
Only to be performed by trained personnel.
0N/OFF
1.
2.
3.
4.
300/150/60kg
Or
600/300/120lb
k
g
Unit 0 lb Unit 1
5.
6kg/15kg
Or
12lb/30lb
kg
ZERO
0
Error Messages
Error Message Definition Required
Solution/Troubleshooting
0¯ ¯ ¯ ¯: Weight above range for calibrated
zero point. Remove load before zeroing
Or
Recalibrate the scale.
0_____:
Weight below range for calibrated
zero point. Remove load before zeroing
Or
Recalibrate the scale.
_____: Indicates an under range condition Remove all loads and zero the
scale.
¯ ¯ ¯ ¯: Capacity exceeded Remove the load and try again. If
the load is great than 6 kg a scale
with a larger capacity is required.
CAL-Er: Calibration error Restart calibration
Lo.bAt: Low Battery Recharge the battery.
Table des matières
Langues :
Autres manuels Brecknell Échelle
Brecknell
Brecknell DSB Manuel d'instructions
Brecknell
Brecknell 6710U Manuel utilisateur
Brecknell
Brecknell MBS-150 Manuel utilisateur
Brecknell
Brecknell DS-1 Manuel utilisateur
Brecknell
Brecknell C3236 Manuel utilisateur
Brecknell
Brecknell DS 1000-LCD Manuel utilisateur
Brecknell
Brecknell 6710 Series Manuel utilisateur
Brecknell
Brecknell PS-7 Manuel d'utilisation
Brecknell
Brecknell HS300 Manuel utilisateur
Brecknell
Brecknell MS-1000 Manuel utilisateur
Brecknell
Brecknell MS16 Manuel utilisateur
Brecknell
Brecknell 405-LCD Manuel utilisateur
Brecknell
Brecknell MS140/300 Manuel utilisateur
Brecknell
Brecknell SBI 110 Manuel utilisateur
Brecknell
Brecknell BS-180 Manuel utilisateur
Brecknell
Brecknell PS 150 Manuel utilisateur
Brecknell
Brecknell PS-500 Manuel utilisateur
Brecknell
Brecknell MS-15 Manuel utilisateur
Brecknell
Brecknell EPB Series Manuel utilisateur
Brecknell
Brecknell 67 U Series Manuel utilisateur
