Bray 762 Series Manuel utilisateur

SERIES 762

BIDIRECTIONAL SLURRY KNIFE GATE

VALVES – BRAY SLURRYSHIELD

Installation, Operation, and Maintenance Manual

BRAY.COM THE HIGH PERFORMANCE COMPANY

SERIES 762 BIDIRECTIONAL SLURRY KNIFE GATE VALVES

Installation, Operation, and Maintenance Manual

contained herein shall not be copied, transferred, conveyed, or displayed in any manner that would

violate its proprietary nature without the express written permission of Bray International, Inc.

 Deﬁnition of Terms 

 Introduction 

 Parts Identiﬁcation 

 Valve Identiﬁcation 

 Safety Information 

 Hazard-Free Use 

 Qualiﬁed Personnel 

 Handling Requirements 

 Storage 

 Installation & Commissioning 

 Operation 

 Actuation and Travel Stop Setting 

 Lockout 

 Standard Maintenance 

 Field Adjustments 

 Actuator Conversion 

 Troubleshooting Guide 

 Return Merchandise Authorization 

TABLE OF CONTENTS

SERIES 762 BIDIRECTIONAL SLURRY KNIFE GATE VALVES

Installation, Operation, and Maintenance Manual

contained herein shall not be copied, transferred, conveyed, or displayed in any manner that would

violate its proprietary nature without the express written permission of Bray International, Inc.

0.0 DEFINITION OF TERMS

All information within this manual is relevant to the safe operation

and proper care of your Bray valve. Please understand the

following examples of information used throughout this manual.

0.0 IDENTIFIES CHAPTER HEADING

0.00 Identiﬁes and explains sequential procedure to be performed.

NOTE: Provides important information related to a procedure.

SAFETY STATEMENTS: To prevent unwanted consequences.

CAUTION

Indicates a potentially hazardous situation which, if not avoided,

may result in minor or moderate injury.

NOTICE

Used without the safety alert symbol, indicates a potential

situation which, if not avoided, may result in an undesirable

result or state, including property damage.

WARNING

Indicates a potentially hazardous situation which, if not avoided,

could result in death or serious injury.

READ AND FOLLOW THESE INSTRUCTIONS CAREFULLY.

SAVE THIS MANUAL FOR FUTURE USE.

SERIES 762 BIDIRECTIONAL SLURRY KNIFE GATE VALVES

Installation, Operation, and Maintenance Manual

contained herein shall not be copied, transferred, conveyed, or displayed in any manner that would

violate its proprietary nature without the express written permission of Bray International, Inc.

1.0 INTRODUCTION

WARNING

Do not exceed the maximum pressure rating of the valve at any

time during in operation.

1.1 Series 762 is a slurry knife gate valve with two elastomer seats

which provide the bidirectional shut-o; sealing is achieved by

the elastomer sleeves inserted in the valve body from either side.

Series 762 valve is suitable for on-o service only and is not

recommended to be used in throttling application. The user

should also check suitability for service with valve type, size,

pressure rating and material of construction for the speciﬁc

application.

For all pressure and temperature capabilities of the valve, please

refer to relevant Bray brochures.

1.2 Additional product information (such as application data,

engineering speciﬁcations, actuator selection, etc.) is available

from your local Bray distributor or sales representative, or online

at BRAY.COM

For complete details on the latest product certiﬁcations,

visit BRAY.COM/Certiﬁcations.

SERIES 762 BIDIRECTIONAL SLURRY KNIFE GATE VALVES

Installation, Operation, and Maintenance Manual

contained herein shall not be copied, transferred, conveyed, or displayed in any manner that would

violate its proprietary nature without the express written permission of Bray International, Inc.

2.0 PARTS IDENTIFICATION

Figure 1: Series 762 Exploded View

Item Description

 Body

 Seat

Gate

 Secondary Seal

 Gland Plate

 Gland Plate Fasteners & Washers

 Locating Bush

 Body Mounting Bolt & Washer

 Body Mounting Nut & Washer

 Grease Nipple

 Body O-Ring

 Drain Plate Gasket (optional)

Item Description

 Drain Plate (optional)

 Drain Plate Fasteners & Washers (opt)

 Drain Plug (optional)

 Seat Retainer

 Seat Retainer Screws

 Stem Guard

 Stem Guard Bolt & Nut

 Travel Stop Fastener

 Travel Stop

 Grub Screws

 Grease Nipple

 Handwheel Assembly Housing

Item Description

 Thrust Bearing

 Handwheel

 Stem

 Stem Nut

 Clevis

 Clevis Bolt

 Clevis Lock Nut

 Bellows

 Bellows Flange

 Bellows Mounting Fasteners

 SuperstructureTower Assembly

 Lock Out Bracket

26 27

SERIES 762 BIDIRECTIONAL SLURRY KNIFE GATE VALVES

Installation, Operation, and Maintenance Manual

contained herein shall not be copied, transferred, conveyed, or displayed in any manner that would

violate its proprietary nature without the express written permission of Bray International, Inc.

3.0 VALVE IDENTIFICATION

3.1 All valves, actuators, or control products are provided with an

identiﬁcation tag that is unique to each device. The following

table is a representation of information that may be included.

Data Label Description

Serial Number SERIAL NUMBER Unique serial number of valve

Valve Size SIZE Valve size eg  in mm

Model MODEL Series number of the Valve

Flange Drill FLG DRILL Flange Drill eg ASME B

CL

Temperature Limits MAX TEMP Maximum temperature in

FC

Maximum Permissible

Pressure CWP Maximum permissible pressure

in psibar(g)

Body Material BODY Material grade of body eg

CF () etc

Gate Material GATE Material grade of gate eg 

Stainless Steel

Packing Material PACKING Material of packing eg PTFE

wEPDM Quad Seal

Seat Material SEAT Material of seat eg Buna-N

SERIES 762 BIDIRECTIONAL SLURRY KNIFE GATE VALVES

Installation, Operation, and Maintenance Manual

contained herein shall not be copied, transferred, conveyed, or displayed in any manner that would

violate its proprietary nature without the express written permission of Bray International, Inc.

4.0 SAFETY INFORMATION

NOTICE

Failure to follow these procedures could aect product warranty.

WARNING

> The valve must only be installed, commissioned, operated,

and repaired by qualiﬁed personnel.

> The device generates a large mechanical force during normal

operation.

> All installation, commissioning, operation, and

maintenance must be performed under strict observation

of all applicable codes, standards, and safety regulations.

> Observe all applicable safety regulations for valves installed

in potentially explosive (hazardous) locations.

WARNING

This valve will discharge media during cycling. This is normal

operation and required to maintain a fully functioning valve. Do

not install this valve over walkways, roadways, electrical or other

equipment without the use of a discharge containment system.

SERIES 762 BIDIRECTIONAL SLURRY KNIFE GATE VALVES

Installation, Operation, and Maintenance Manual

contained herein shall not be copied, transferred, conveyed, or displayed in any manner that would

violate its proprietary nature without the express written permission of Bray International, Inc.

5.0 HAZARD-FREE USE

NOTICE

Failure to follow these procedures could aect product warranty.

5.1 This device left the factory in proper condition to be safely

installed and operated in a hazard-free manner. The notes and

warnings in this document must be observed by the user if this

safe condition is to be maintained and hazard-free operation of

the device assured.

5.2 Take all necessary precautions to prevent damage to the valve

due to rough handling, impact, or improper storage. Do not use

abrasive compounds to clean the valve, or scrape metal surfaces

with any objects.

5.3 The control systems in which the valve is installed must have

proper safeguards — to prevent injury to personnel, or damage to

equipment — should failure of system components occur.

5.4 The upper limits of permitted pressure and temperature

(depending on the housing and liner materials) must be

observed. These limits are shown on the valve identiﬁcation tag.

5.5 The valve must not be operated until the following documents

have been observed:

> Declaration on EU Directives

> IOM Manual (supplied with the product).

SERIES 762 BIDIRECTIONAL SLURRY KNIFE GATE VALVES

Installation, Operation, and Maintenance Manual

contained herein shall not be copied, transferred, conveyed, or displayed in any manner that would

violate its proprietary nature without the express written permission of Bray International, Inc.

6.0 QUALIFIED PERSONNEL

NOTICE

Failure to follow these procedures could aect product warranty.

6.1 A qualiﬁed person (in terms of this document) is one who is

familiar with the installation, commissioning, and operation of the

device, and who has appropriate qualiﬁcations, such as:

6.1.1 > Is trained in the operation and maintenance of electrical

equipment and systems in accordance with established safety

practices.

6.1.2 > Is trained or authorized to energize, de-energize, ground, tag,

and lock electrical circuits and equipment in accordance with

established safety practices.

6.1.3 > Is trained in the proper use and care of personal protective

equipment (PPE) in accordance with established safety

practices.

6.1.4 > Is trained in the commissioning, operation, and maintenance of

equipment in hazardous locations — in cases where the device

is installed in a potentially explosive (hazardous) location.

SERIES 762 BIDIRECTIONAL SLURRY KNIFE GATE VALVES

Installation, Operation, and Maintenance Manual

contained herein shall not be copied, transferred, conveyed, or displayed in any manner that would

violate its proprietary nature without the express written permission of Bray International, Inc.

7.0 HANDLING REQUIREMENTS

7.1 Packed Valves

7.1.1 Crates: Lifting and handling of the packed valves in crates will be

carried out by a fork lift truck, by means of the appropriate fork

hitches.

7.1.2 Cases: The lifting of packed valves in cases will be carried out in

the lifting points and in the center of gravity position which has

been marked. The transportation of all packed material must be

carried out safely and following the local safety regulations.

7.2 Unpacked Valves

7.2.1 Lifting and handling of valves should be carried out by using

appropriate means and observing the carrying limits. Handling

must be carried out on pallets, protecting all machined surfaces

to avoid any damage.

7.2.2 With large bore valves, rigging the load must be carried out by

using the appropriate tools to prevent the valve from falling or

moving during the lifting and handling.

CAUTION

For handling and/or lifting, the lifting equipment (fasteners,

hooks, etc.) must be sized and selected while taking into account

the product weight indicated in our packing list and/or delivery

note. Lifting and handling must be performed only by qualiﬁed

personnel.

Fasteners must be protected by plastic covers in sharp corner

areas.

Caution must be taken during handling to avoid this equipment

passing over workers, or over any other place where a possible

fall could cause injury or damage. In all cases, local safety

regulations must be respected.

Table des matières

Autres manuels Bray Unité de contrôle

Bray

Bray ACRIS 24 Series 24 Manuel utilisateur

Bray

Bray 940 Series Manuel utilisateur

Bray

Bray FlowTek F15 Series Manuel utilisateur

Bray

Bray TRI LOK Series Manuel utilisateur

Bray

Bray TRI LOK Manuel utilisateur

Bray

Bray FLOW-TEK 19 Series Manuel utilisateur

Bray

Bray Flow-Tek Triad Series Mode d’emploi

Bray

Bray TRI LOK Manuel utilisateur

Bray

Bray TRI LOK Manuel utilisateur

Bray

Bray 768 Series Manuel utilisateur

Bray

Bray 942 Series Manuel utilisateur

Bray

Bray Flow-Tek 7000 Series Manuel utilisateur

Bray

Bray S30/S70 Manuel utilisateur

Bray

Bray TRI LOK Class 150 Manuel utilisateur

Bray

Bray FLOW-TEK Series Manuel utilisateur

Bray

Bray 63-N4 Series Manuel d'instructions

Bray

Bray 752 Series Manuel utilisateur

Bray

Bray Flow-Tek 5000 Series Manuel utilisateur

Bray

Bray 740 Series Manuel utilisateur

Bray

Bray 19L Series Manuel utilisateur

Bray

Bray TRI LOK Manuel utilisateur

Bray

Bray MCCANNALOK Manuel utilisateur

Bray

Bray 950 Series Manuel utilisateur

Bray

Bray FlowTek F30 Series Manuel utilisateur

Manuels Unité de contrôle populaires d'autres marques

Festo

Festo Compact Performance CP-FB6-E Manuel de la liste des pièces

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manuel utilisateur

JS Automation

JS Automation MPC3034A Manuel utilisateur

JAUDT

JAUDT SW GII 6406 Series Guide rapide

Spektrum

Spektrum Air Module System Manuel utilisateur

BOC Edwards

BOC Edwards Q Series Manuel utilisateur

KHADAS

KHADAS BT Magic Manuel utilisateur

Etherma

Etherma eNEXHO-IL Manuel utilisateur

PMFoundations

PMFoundations Attenuverter Manuel utilisateur

GEA

GEA VARIVENT Manuel utilisateur

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manuel utilisateur

Altronix

Altronix LINQ8PD Instructions de montage

Eaton

Eaton Powerware Series Manuel utilisateur

WAGO

WAGO 750-407/040-000 Manuel utilisateur

Sony

Sony CCU-590 Manuel utilisateur

Graco

Graco 25D614 Manuel utilisateur

Task Force Tips

Task Force Tips YE-RF-900 Manuel de programmation

Shini

Shini SPV-U Series Manuel utilisateur