B+K precision 881 Manuel utilisateur

Instruction Manual

Model 881

In-Circuit ESR & DCR Cap Tester

www.GlobalTestSupply.com

Find Quality Products Online at: sales@GlobalTestSupply.com

SAFETY GUIDELINES

WARNING

An electrical current of over 10 milliamps passing through the heart will stop most human

hearts. Voltage of as low as 35Volts dc or ac rms should be considered hazardous since it can

produce lethal current under certain conditions. Be sure to observe the following safety

precautions:

1. There are no high voltages in the Cap Tester, but the equipment under test usually

contains hazardous high voltage. Always follow the safety recommendations of the

manufacturer of your equipment.

2. Some equipment may be wired as a “hot chassis” type; equipment using two-wire

power plugs are always suspected and it may even include those with polarized plugs. Never

touch chassis of “hot chassis” type equipment to avoid the possibility of a serious, possibly fatal

electrical shock.

3. Don’t expose yourself needlessly to high voltage; only remove

housings and covers when necessary.

4. Familiarize yourself with the equipment being tested and the location of its high voltage

points. However be aware that high voltage may appear at unexpected points in defective

equipment.

5. Never work alone. Someone should be nearby to render aid if needed. Training in

CPR(Cardio-pulmonary resuscitation) is highly recommended.

www.GlobalTestSupply.com

Find Quality Products Online at: sales@GlobalTestSupply.com

In-Circuit ESR & DCR Cap Tester

Introduction:

The In-circuit ESR & DCR capacitor tester is specially designed to measure ESR (equivalent Series

Resistance) on capacitors in the range of 0.47uf and up, in or out of circuit. The output test

frequency of the meter is a 100 KHz SINE WAVE. The output voltage is 15mV pp and will not

turn on any solid-state devices in the circuit under test.

It includes a one–handed tweezers test probe, microprocessor controlled, automatically

discharges the capacitors under test, checks for low DCR, checks and displays ESR on a 25

segment LED bar scale, and beeps from one to five beeps depending on the ESR reading of the

capacitor. It has a three-colored chart on the front panel that show typical ESR readings of

good, fair, and bad capacitors depending on their capacitance.

OPERATION:

1. Place the mode switch to the position for measurement.

2. Turn the unit on and wait; the unit will beep once when ready.

3. Hold the tweezer’s test probe cross the capacitor leads to measure ESR of the capacitor.

www.GlobalTestSupply.com

Find Quality Products Online at: sales@GlobalTestSupply.com

Controls and Indicators

1. Power Switch –Power on or off

2. DCR Low Indicator –LED on when DCR low then 30 ohms

3. Mode switch –Selects test capacitor ESR or test capacitor DCR&ESR both.

4. ESR or DCR Indicator –Indicate the ESR or DCR

5. Colored chart –The three-colored chart that show typical ESR readings of good, fair, and bad

capacitors depending on their capacitance.

6. Square connector –Capacitance

7. Bat Low –Indicates battery condition.

8. AC Adapter Jack –9V DC, 100mA center pin + adapter input.

www.GlobalTestSupply.com

Find Quality Products Online at: sales@GlobalTestSupply.com

APPLICATIONS

Using the tester to measure electrolytic capacitors in or out of circuit.

When the meter is turned on, it will automatically calibrate the internal circuit, and then it will

beep once to indicate it’s ready. (Note: Before the unit beeps to signal it is ready, don’t have

the tweezer’s test probes shorted together or connected to a capacitor, otherwise the meter

will continue to sound an alarm until the test probe is opened or the capacitor is removed.)

The meter has two modes for performing in-circuit ESR measurements (“DCR & ESR” mode and

“ESR” mode). Place the mode switch to the position for measurement.

To measure the ESR on a capacitor, hold the tweezer’s test probe cross the capacitor leads. The

meter’s probes are nonpolar.

On the “ESR” mode, the meter performs a set cycle of tests each time it is connected to a

capacitor. First it discharges the capacitor, then it measures the ESR and indicates the range of

the value with the 25 LED bar, and also sounds one or more times depending on the ESR of the

capacitor (see table 1). The three-color chart on the panel shows typical electrolytic capacitors

ESR readings. If the capacitor’s ESR range is in the green areas, it is good, and if the capacitor’s

ESR range is in the red areas, it must be replaced. If the capacitor’s ESR range is in the yellow

areas it’s questionable and is up to the technician to decide on whether to replace this

capacitor, or not. The capacitor with higher voltage ratings and used in circuits not requiring

particularly low ESR may still work adequately in the yellow area. However, the modern solid

circuits such as switch power supplies require low ESR capacitor. The ESR of a good capacitor

depends upon the type of material, value and voltage rating.

On the “ESR” mode, the meter will indicate that a shorted capacitor is good because the meter

does not perform the DCR measurement. Therefore, only in the “DCR & ESR mode” will the

meter detect shorted capacitor in its DCR cycle.

Table 1

Beeps from 1 to 5 beeps depending on ESR

ESR range ohms: 0 –0.5One sound

0.5 –1Two sounds

1 –3Three sounds

3 –8Four sounds

8 –30Five sounds

www.GlobalTestSupply.com

Find Quality Products Online at: sales@GlobalTestSupply.com

On the “DCR & ESR” mode, first it discharges the capacitor, then it checks the DC resistance and

if the DC resistance is less than 30 ohm, it will stop on the DCR cycle, otherwise, it measures the

ESR and indicates the range of the value with the 25 LED bar. On this mode, the meter detects

shorted capacitor in its DCR cycle.

If the meter stops on the DCR cycle, it first sounds an alarm and turns on the DCR LOW led, then

indicates DC resistance by flashing the LED on the LED bar and also sounds one or more times

depending on the DC resistance (see table 2).

Table 2

Measures DCR by flashing the LED on the LED bar

DCR range ohms: 0 - 0.5flashing the 0.5LED

0.5 - 1.2flashing the 1.2LED

1.2 - 2.5flashing the 2.5LED

2.5 - 4.5flashing the 4.5LED

4.5 - 10flashing the 10LED

10 - 20flashing the 20LED

20 - 30flashing the 30LED

Beeps from 1 to 3 beeps depending on DCR

DCR range ohms: 0 –1.2One sound

1.2 –4.5Two sounds

4.5 –3 0Three sounds

The meter automatically discharges capacitors before testing. However, if capacitors are large

enough, and there is enough voltage stored, it may damage the test probe. We recommend

that for a large capacitor, you should discharge it before you test it.

You can use the “ESR” mode to test a capacitor with a parallel inductor if the inductor has a

large inductance at 100 kHz test frequency and have no effect on the ESR reading.

On the “ESR” mode, the meter is an AC ohm meter, it can be used to measure low value non-

inductive resistors. It also may be used to measure small inductors and compare meter reading

to the known good inductors.

www.GlobalTestSupply.com

Find Quality Products Online at: sales@GlobalTestSupply.com

SPECIFICATIONS

Open circuit probe voltage 15mV pp

Output test frequency 100 KHz sine wave

Measures ESR

ESR range ohms 0.1 –30 (25 segment LED bar scale)

Beeps from 1 to 5 beeps depending on ESR of capacitor

Measures DCR

DCR range ohms 0.5 –30 flashing the LED

Power One 9V battery or an external

AC adapter (9V DC 100mA

5.5mm x 2.1mm center pin+)

Power drain 10mA typical

Dimensions 1.5” x 3.8” x 5.7”

Note: Specifications and information in this manual are subject to change without

notice. Please visit for the most current product information.

www.GlobalTestSupply.com

Find Quality Products Online at: sales@GlobalTestSupply.com

Service Information

Warranty Service: Please go to the support and service section on our website to obtain a RMA

#. Return the product in the original packaging with proof of purchase to the address below.

Clearly state on the RMA the performance problem and return any leads, probes, connectors

and accessories that you are using with the device.

Non-Warranty Service: Please go to the support and service section on our website to obtain a

RMA #. Return the product in the original packaging to the address below. Clearly state on the

RMA the performance problem and return any leads, probes, connectors and accessories that

you are using with the device. Customers not on an open account must include payment in the

form of a money order or credit card. For the most current repair charges please refer to the

service and support section on our website.

Return all merchandise to B&K Precision Corp. with prepaid shipping. The flat-rate repair charge

for Non-Warranty Service does not include return shipping. Return shipping to locations in

North America is included for Warranty Service. For overnight shipments and non-North

American shipping fees please contact B&K Precision Corp.

Include with the returned instrument your complete return shipping address, contact name,

phone number and description of problem.

www.GlobalTestSupply.com

Find Quality Products Online at: sales@GlobalTestSupply.com

Limited One-Year Warranty

B&K Precision Corp. warrants to the original purchaser that its products and the component

parts thereof, will be free from defects in workmanship and materials for a period of one year

from date of purchase.

B&K Precision Corp. will, without charge, repair or replace, at its option, defective product or

component parts. Returned product must be accompanied by proof of the purchase date in the

form of a sales receipt.

To help us better serve you, please complete the warranty registration for your new instrument

via our website bkprecision.com

Exclusions: This warranty does not apply in the event of misuse or abuse of the product or as a

result of unauthorized alterations or repairs. The warranty is void if the serial number is altered,

defaced or removed.

B&K Precision Corp. shall not be liable for any consequential damages, including without

limitation damages resulting from loss of use. Some states do not allow limitations of incidental

or consequential damages. So the above limitation or exclusion may not apply to you.

This warranty gives you specific rights and you may have other rights, which vary from state-to-

state.

www.GlobalTestSupply.com

Find Quality Products Online at: sales@GlobalTestSupply.com

Autres manuels pour 881

Table des matières

Autres manuels B+K precision Équipement de test

B+K precision

B+K precision 1045B Manuel utilisateur

B+K precision

B+K precision 2560 Series Manuel utilisateur

B+K precision

B+K precision 8500 Manuel utilisateur

B+K precision

B+K precision 881 Manuel utilisateur

B+K precision

B+K precision 2194 Manuel utilisateur

B+K precision

B+K precision 2510 Series Manuel utilisateur

B+K precision

B+K precision 2190B Manuel utilisateur

B+K precision

B+K precision 2552 Manuel utilisateur

B+K precision

B+K precision 2120C Manuel utilisateur

B+K precision

B+K precision 1856D Manuel utilisateur

B+K precision

B+K precision 2532B Manuel utilisateur

B+K precision

B+K precision Sefram MW9325 Manuel utilisateur

B+K precision

B+K precision 8500B Series Manuel utilisateur

B+K precision

B+K precision 1472B Manuel utilisateur

B+K precision

B+K precision 5105A Manuel utilisateur

B+K precision

B+K precision 2540 Manuel utilisateur

B+K precision

B+K precision TL89S1 Mode d’emploi

B+K precision

B+K precision Sefram MW9092 Manuel utilisateur

B+K precision

B+K precision 1474 Manuel utilisateur

B+K precision

B+K precision 8500B Series Manuel du propriétaire

B+K precision

B+K precision 2540C Series Manuel utilisateur

B+K precision

B+K precision 2190D Manuel utilisateur

B+K precision

B+K precision 575A Manuel utilisateur

B+K precision

B+K precision 2560B Series Manuel utilisateur

Manuels Équipement de test populaires d'autres marques

SMART

SMART KANAAD SBT XTREME 3G Series Manuel utilisateur

Agilent Technologies

Agilent Technologies BERT Serial Manuel utilisateur

Agilent Technologies

Agilent Technologies N3280A Manuel utilisateur

Vernier

Vernier Go Direct Voltage Manuel utilisateur

Lifeloc

Lifeloc R.A.D.A.R. Manuel utilisateur

Fluke

Fluke T5-600 Instructions d'utilisation et d'installation

Mercury

Mercury TSL01 Manuel utilisateur

MAHA

MAHA MBT Series Manuel utilisateur

Fuji Electric

Fuji Electric P-61 Manuel utilisateur

ETC

ETC SealerAtor Manuel utilisateur

Skyfine

Skyfine ETHYWAY V2 Manuel utilisateur

Appion

Appion G5 Twin Manuel utilisateur

PCB Piezotronics

PCB Piezotronics 8159-0112A Manuel utilisateur

BW Technologies

BW Technologies MicroDock II Manuel utilisateur

Sun Nuclear

Sun Nuclear 1027 Manuel utilisateur

Biomark

Biomark HPR LITE READER Manuel utilisateur

Hioki

Hioki 3169-20 Manuel utilisateur

Ashcroft

Ashcroft ATE-100 Manuel utilisateur