B+K precision 2560B Series Manuel utilisateur

Safety Summary

The following safety precautions apply to both operating and maintenance personnel and must be followed during all

phases of operation, service, and repair of this instrument.

Before applying power to this instrument:

•

Read and understand the safety and operational information in this manual.

•

Apply all the listed safety precautions.

•

Verify that the voltage selector at the line power cord input is set to the correct line voltage. Operating the instrument

at an incorrect line voltage will void the warranty.

•

Make all connections to the instrument before applying power.

•

Do not operate the instrument in ways not specified by this manual or by B&K Precision.

Failure to comply with these precautions or with warnings elsewhere in this manual violates the safety standards of design,

manufacture, and intended use of the instrument. B&K Precision assumes no liability for a customer’s failure to comply

with these requirements.

Category rating

The IEC 61010 standard defines safety category ratings that specify the amount of electrical energy available and the

voltage impulses that may occur on electrical conductors associated with these category ratings. The category rating is

a Roman numeral of I, II, III, or IV. This rating is also accompanied by a maximum voltage of the circuit to be tested,

which defines the voltage impulses expected and required insulation clearances. These categories are:

Category I (CAT I):

Measurement instruments whose measurement inputs are not intended to be connected to the

mains supply. The voltages in the environment are typically derived from a limited-energy trans-

former or a battery.

Category II (CAT II):

Measurement instruments whose measurement inputs are meant to be connected to the mains

supply at a standard wall outlet or similar sources. Example measurement environments are portable

tools and household appliances.

Category III (CAT III):

Measurement instruments whose measurement inputs are meant to be connected to the mains

installation of a building. Examples are measurements inside a building’s circuit breaker panel

or the wiring of permanently-installed motors.

Category IV (CAT IV):

Measurement instruments whose measurement inputs are meant to be connected to the primary

power entering a building or other outdoor wiring.

Do not use this instrument in an electrical environment with a higher category rating than what is specified in this manual

for this instrument.

You must ensure that each accessory you use with this instrument has a category rating equal to or higher than the

instrument’s category rating to maintain the instrument’s category rating. Failure to do so will lower the category rating

of the measuring system.

Electrical Power

This instrument is intended to be powered from a CATEGORY II mains power environment. The mains power should be

115 V RMS or 230 V RMS. Use only the power cord supplied with the instrument and ensure it is appropriate for your

country of use.

Ground the Instrument

To minimize shock hazard, the instrument chassis and cabinet must be connected to an electrical safety ground. This

instrument is grounded through the ground conductor of the supplied, three-conductor AC line power cable. The power

cable must be plugged into an approved three-conductor electrical outlet. The power jack and mating plug of the power

cable meet IEC safety standards.

Do not alter or defeat the ground connection. Without the safety ground connection, all accessible conductive parts

(including control knobs) may provide an electric shock. Failure to use a properly-grounded approved outlet and the

recommended three-conductor AC line power cable may result in injury or death.

Unless otherwise stated, a ground connection on the instrument’s front or rear panel is for a reference of potential only

and is not to be used as a safety ground. Do not operate in an explosive or flammable atmosphere.

Do not operate the instrument in the presence of flammable gases or vapors, fumes, or finely-divided particulates.

The instrument is designed to be used in office-type indoor environments. Do not operate the instrument

•

In the presence of noxious, corrosive, or flammable fumes, gases, vapors, chemicals, or finely-divided particulates.

•

In relative humidity conditions outside the instrument’s specifications.

•

In environments where there is a danger of any liquid being spilled on the instrument or where any liquid can condense

on the instrument.

•

In air temperatures exceeding the specified operating temperatures.

•

In atmospheric pressures outside the specified altitude limits or where the surrounding gas is not air.

•

In environments with restricted cooling air flow, even if the air temperatures are within specifications.

•

In direct sunlight.

This instrument is intended to be used in an indoor pollution degree 2 environment. The operating temperature range is

∘

C to 40

∘

C and 20% to 80% relative humidity, with no condensation allowed. Measurements made by this instrument

may be outside specifications if the instrument is used in non-office-type environments. Such environments may include

rapid temperature or humidity changes, sunlight, vibration and/or mechanical shocks, acoustic noise, electrical noise,

strong electric fields, or strong magnetic fields.

Do not operate instrument if damaged

If the instrument is damaged, appears to be damaged, or if any liquid, chemical, or other material gets on or inside the

instrument, remove the instrument’s power cord, remove the instrument from service, label it as not to be operated,

and return the instrument to B&K Precision for repair. Notify B&K Precision of the nature of any contamination of the

instrument.

Clean the instrument only as instructed

Do not clean the instrument, its switches, or its terminals with contact cleaners, abrasives, lubricants, solvents, acids/bases,

or other such chemicals. Clean the instrument only with a clean dry lint-free cloth or as instructed in this manual. Not

for critical applications

This instrument is not authorized for use in contact with the human body or for use as a component in a life-support

device or system.

Do not touch live circuits

Instrument covers must not be removed by operating personnel. Component replacement and internal adjustments must

be made by qualified service-trained maintenance personnel who are aware of the hazards involved when the instrument’s

covers and shields are removed. Under certain conditions, even with the power cord removed, dangerous voltages may

exist when the covers are removed. To avoid injuries, always disconnect the power cord from the instrument, disconnect

all other connections (for example, test leads, computer interface cables, etc.), discharge all circuits, and verify there

are no hazardous voltages present on any conductors by measurements with a properly-operating voltage-sensing device

before touching any internal parts. Verify the voltage-sensing device is working properly before and after making the

measurements by testing with known-operating voltage sources and test for both DC and AC voltages. Do not attempt

any service or adjustment unless another person capable of rendering first aid and resuscitation is present.

Do not insert any object into an instrument’s ventilation openings or other openings.

Hazardous voltages may be present in unexpected locations in circuitry being tested when a fault condition in the circuit

exists.

Fuse replacement must be done by qualified service-trained maintenance personnel who are aware of the instrument’s fuse

requirements and safe replacement procedures. Disconnect the instrument from the power line before replacing fuses.

Replace fuses only with new fuses of the fuse types, voltage ratings, and current ratings specified in this manual or on

the back of the instrument. Failure to do so may damage the instrument, lead to a safety hazard, or cause a fire. Failure

to use the specified fuses will void the warranty.

Note:

Servicing

Do not substitute parts that are not approved by B&K Precision or modify this instrument. Return the instrument to

B&K Precision for service and repair to ensure that safety and performance features are maintained.

For continued safe use of the instrument

•

Do not place heavy objects on the instrument.

•

Do not obstruct cooling air flow to the instrument.

•

Do not place a hot soldering iron on the instrument.

•

Do not pull the instrument with the power cord, connected probe, or connected test lead.

•

Do not move the instrument when a probe is connected to a circuit being tested.

Working Environment

Environment

This instrument is intended for indoor use and should be operated in a clean, dry environment.

Temperature

Operating: 0℃ to +40℃

Non-operation:-20℃ to +60℃

Direct sunlight, radiators, and other heat sources should be taken into account when assessing the ambient temperature.

Humidity

Operating: 85% RH, 40 ℃, 24 hours

Non-operating: 85% RH, 65 ℃, 24 hours

Altitude

Operating: less than 3 Km

Non-operation: less than 15 Km

Installation (overvoltage) Category

This product is powered by mains conforming to installation (overvoltage) category II.

Degree of Pollution

The oscilloscopes may be operated in environments of Pollution Degree II.

Degree of Pollution II refers to a working environment which is dry and non-conductive pollution occurs. Occasional

temporary conductivity caused by condensation is expected.

IP Rating

IP20 (as defined in IEC 60529).

Compliance Statements

Disposal of Old Electrical & Electronic Equipment (Applicable in the European Union and other European

countries with separate collection systems)

This product is subject to Directive 2002/96/EC of the European Parliament

and the Council of the European Union on waste electrical and electronic equipment

(WEEE), and in jurisdictions adopting that Directive, is marked as being put on the

market after August 13, 2005, and should not be disposed of as unsorted municipal

waste. Please utilize your local WEEE collection facilities in the disposition of this

product and otherwise observe all applicable requirements.

Safety Symbols

Symbol

Description

indicates a hazardous situation which, if not avoided, will result in death or serious injury.

indicates a hazardous situation which, if not avoided, could result in death or serious injury

indicates a hazardous situation which, if not avoided, will result in minor or moderate injury

Refer to the text near the symbol.

Electric Shock hazard

Alternating current (AC)

Chassis ground

Earth ground

This is the In position of the power switch when instrument is ON.

This is the Out position of the power switch when instrument is OFF.

is used to address practices not related to physical injury.

 
 
 Contents 
1
General Information 13 
1.1 
Product Overview 13 
1.2 
Features 14 
1.3 
Contents 15 
1.4 
Dimensions 15 
1.5 
Front Panel Overview 16 
1.6 
Rear Panel Overview 17 
1.7 
Touch Screen Overview 18 
2
Getting Started 19 
2.1 
Input Power Requirements 19 
2.2 
Fuse Requirements and Replacement 20 
2.3 
Preliminary Check 21 
2.3.1 
Verify AC Input Voltage 21 
2.3.2 
Connect Power 21 
2.3.3 
Self-Test 21 
2.3.4 
Self-Cal 21 
2.3.5 
Check Model and Firmware Version 21 
2.3.6 
Function Check 22 
2.4 
Probe Safety 23 
3
Control Panel 25 
3.1 
Vertical Control 25 
3.2 
Horizontal Control 26 
3.3 
Trigger Control 26 
3.4 
Run/Stop Key 27 
3.5 
Auto Setup Key 27 
3.6 
Analysis Keys 27 
3.7 
Universal Knob 28 
3.8 
Menu Keys 28 
3.9 
Other Keys 29 
4
Acquisition 30 
4.1 
Changing Acquisition Mode 30 
4.2 
Sequence 32 
5
History 33 
6
Horizontal Control 34 
6.1 
Adjusting the Horizontal Scale (time/div) 34 
6.2 
Adjusting the Horizontal Delay (position) 35 
6.3 
Panning and Zooming Single or Stopped Acquisitions 36 
6.4 
Horizontal Scale (Coarse/Fine) 36 
6.5 
Zoom 37 
6.6 
Roll 38 

Vertical Control 39

7.1

Enabling Channels 39

7.1.1

Channel Enable/Disable From the Touch Screen 39

7.2

Vertical Scale 40

7.2.1

Coarse/Fine Adjustment 40

7.3

Vertical Position 40

7.4

Channel Setup 41

7.4.1

Channel Coupling

7.4.2

Bandwidth Limit

7.4.3

Probe Attenuation

7.4.4

Label

7.4.5

Apply To

7.4.6

Impedance

7.4.7

Unit

7.4.8

Deskew

7.4.9

Invert

7.4.10

Trace

Digital Channels

8.1

LP2560 Probe 46

8.2

Connecting the Digital Probes 47

8.3

Acquiring Digital Waveforms 47

8.4

Displaying Digital Channels 48

8.5

Turning Individual Channels On or Off 49

8.6

Logic Threshold for Digital Channels 50

8.7

Displaying Digital Channels as a Bus 50

Trigger 52

9.1

Trigger Source 53

9.2

Trigger Types 54

9.2.1

Edge Trigger 54

9.2.2

Slope Trigger 55

9.2.3

Pulse Trigger 57

9.2.4

Video Trigger 59

9.2.5

Window Trigger 62

9.2.6

Interval Trigger 64

9.2.7

Dropout Trigger 65

9.2.8

Runt Trigger 67

9.2.9

Pattern Trigger 68

9.3

Trigger Mode 70

9.4

Trigger Level 71

9.5

Trigger Coupling 72

9.6

Trigger Holdoff 73

9.6.1

Holdoff by Time 73

9.6.2

Holdoff by Event 73

9.6.3

Start Holdoff On 74

9.7

Noise Reject 75

9.8

Zone Trigger 76

9.8.1

Creating and Moving Zones 76

Serial Trigger and Decode 79

10.1

I2C Trigger and Serial Decode 79

10.1.1

Setup for I2C Signals 79

10.1.2

I2C Trigger 81

10.1.3

I2C Serial Decode 84

10.2

SPI Trigger and Serial Decode 85

10.2.1

Setup for SPI Signals 85

10.2.2

SPI Trigger 88

9 
 
10.2.3 
SPI Serial Decode 89 
10.3 
UART Trigger and Serial Decode 90 
10.3.1 
Setup for UART Signals 90 
10.3.2 
UART Trigger 91 
10.3.3 
UART Serial Decode 92 
10.4 
CAN Trigger and Serial Decode 94 
10.4.1 
Setup for CAN Signals 94 
10.4.2 
CAN Trigger 94 
10.4.1 CAN Serial Decode 95 
10.5 
LIN Trigger and Serial Decode 97 
10.5.1 
Setup for LIN Signals 97 
10.5.2 
LIN Trigger 97 
10.5.1 Interpreting LIN Decode 99 
10.6 
FlexRay Trigger and Serial Decode 100 
10.6.1 
FlexRay Signal Configuration 100 
10.6.2 
FlexRay Trigger 101 
10.6.3 
FlexRay Serial Decode 102 
10.7 
CAN FD Trigger and Serial Decode 104 
10.7.1 
CAN FD Signal Configuration 104 
10.7.2 
CAN FD Trigger 106 
10.7.3 
CAN FD Serial Decode 106 
10.8 
I2S Trigger and Serial Decode 108 
10.8.1 
I2S Signal Configuration 108 
10.8.2 
I2S Trigger 111 
10.8.3 
I2S Serial Decode 112 
10.9 
MIL-STD-1553B Trigger and Serial Decode 113 
10.9.1 
MIL-STD-1553B Signal Configuration 113 
10.9.2 
MIL-STD-1553B Serial Decode 114 
10.10 
SENT Trigger and Serial Decode 116 
10.10.1 
SENT Signal Configuration 116 
10.10.2 
SENT Trigger 118 
10.10.3 
SENT Serial Decode 121 
10.11 
Manchester Trigger and Serial Decode 124 
10.11.1 
Manchester Signal Configuration 124 
10.11.2 
Manchester Serial Decode 126 
11 
Cursors 128 
11.1 
X Cursors 129 
11.2 
Y Cursors 130 
11.3 
Display Style 132 
11.4 
Make Cursor Measurements 133 
11.5 
Cursors Reference 134 
12 
Measure 136 
12.1 
Measurement Modes 136 
12.2 
Set Measurement Types 138 
12.3 
Type of Measurement 139 
12.3.1 
Vertical Measurements 139 
12.3.2 
Horizontal Measurements 141 
12.3.3 
Miscellaneous Measurements 142 
12.3.4 
Delay Measurements 143 
12.4 
Trend 144 
12.5 
Simple Measurements 145 
12.6 
Measurement Statistics 145 
12.7 
Statistics Histogram 146 
12.8 
Gate 146 
12.9 
Amplitude Strategy 147 
12.10 
Threshold 148 

Math 149

13.1

Units for Math Waveforms 150

13.2

Arithmetic 151

13.2.1

Subtraction Example 151

13.2.2

Average 152

13.2.3

ERES 153

13.3

Algebra 154

13.3.1

Differentiate

154

13.3.2

Integrate

155

13.3.3

Square Root

156

13.3.4

Absolute

157

13.3.5

Sign

157

13.3.6

Exp/Exp10

158

13.3.7

Ln/Lg

159

13.3.8

Interpolate

159

13.4

Frequency Analysis (FFT Operation)

160

13.4.1

Setting FFT Parameters 160

13.4.2

Parameter Display Area 162

13.4.3

Vertical 162

13.4.4

Horizontal 163

13.5

FFT Tools 163

13.5.1

Peaks Tool 163

13.5.2

Markers Tool 164

13.5.3

Measure the FFT Waveform 165

13.6

Formula Editor 166

Reference Waveform 167

14.1

Save REF Waveform to Internal Memory 167

14.2

Display REF Waveforms 167

Search 169

Navigate 171

16.1

Navigate by Time 171

16.2

Navigate by Search Event 172

16.3

Navigate by History Frame 173

Mask Test 174

17.1

Mask Setup 175

17.1.1

Create Mask 175

17.1.2

Mask Editor 176

17.2

Operation 178

17.3

Pass/Fail Rule 178

Counter 179

18.1

Counter Configuration 179

18.2

Mode 180

Power Analysis 181

19.1

Power Quality 182

19.1.1

Type 182

19.1.2

Input Setup 183

19.2

Current Harmonics 184

19.2.1

Configuration 184

19.2.2

Standard 184

19.2.3

Parameter Description 185

15.1

Setting

169

15.2

Copy

169

15.3

Results

169

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels B+K precision Équipement de test

B+K precision

B+K precision 851 Manuel utilisateur

B+K precision

B+K precision 2530 Manuel utilisateur

B+K precision

B+K precision 2190B Manuel utilisateur

B+K precision

B+K precision Sefram MW9325 Manuel utilisateur

B+K precision

B+K precision BK8510B Manuel utilisateur

B+K precision

B+K precision 1856D Manuel utilisateur

B+K precision

B+K precision 8500B Series Manuel utilisateur

B+K precision

B+K precision 8600/B Manuel utilisateur

B+K precision

B+K precision 2190D Manuel utilisateur

B+K precision

B+K precision 8600 Series Manuel utilisateur

B+K precision

B+K precision 4040A Manuel utilisateur

B+K precision

B+K precision 2125A Manuel utilisateur

B+K precision

B+K precision 2540B Manuel utilisateur

B+K precision

B+K precision 8500 Manuel utilisateur

B+K precision

B+K precision 1472B Manuel utilisateur

B+K precision

B+K precision 1045B Manuel utilisateur

B+K precision

B+K precision 2540 Manuel utilisateur

B+K precision

B+K precision 2511 Manuel utilisateur

B+K precision

B+K precision 5105A Manuel utilisateur

B+K precision

B+K precision 2194 Manuel utilisateur

B+K precision

B+K precision 8500B Series Manuel du propriétaire

B+K precision

B+K precision 2522C Manuel utilisateur

B+K precision

B+K precision 2160A Manuel utilisateur

B+K precision

B+K precision 2120C Manuel utilisateur

Manuels Équipement de test populaires d'autres marques

SMART

SMART KANAAD SBT XTREME 3G Series Manuel utilisateur

Agilent Technologies

Agilent Technologies BERT Serial Manuel utilisateur

Agilent Technologies

Agilent Technologies N3280A Manuel utilisateur

Vernier

Vernier Go Direct Voltage Manuel utilisateur

Lifeloc

Lifeloc R.A.D.A.R. Manuel utilisateur

Fluke

Fluke T5-600 Instructions d'utilisation et d'installation

Mercury

Mercury TSL01 Manuel utilisateur

MAHA

MAHA MBT Series Manuel utilisateur

Fuji Electric

Fuji Electric P-61 Manuel utilisateur

ETC

ETC SealerAtor Manuel utilisateur

Skyfine

Skyfine ETHYWAY V2 Manuel utilisateur

Appion

Appion G5 Twin Manuel utilisateur

PCB Piezotronics

PCB Piezotronics 8159-0112A Manuel utilisateur

BW Technologies

BW Technologies MicroDock II Manuel utilisateur

Sun Nuclear

Sun Nuclear 1027 Manuel utilisateur

Biomark

Biomark HPR LITE READER Manuel utilisateur

Hioki

Hioki 3169-20 Manuel utilisateur

Ashcroft

Ashcroft ATE-100 Manuel utilisateur