Bose Panaray MA12 Manuel utilisateur

Service Manual

Panaray®MA12 Modular Line Array

Loudspeaker System

Electronic Copy Only

CAUTION: The Bose®Panaray MA12 Modular Line Array Loudspeaker System

contains no user-serviceable parts. To prevent warranty infractions,

refer servicing to warranty service stations or factory service.

PROPRIETARY INFORMATION

THIS DOCUMENT CONTAINS PROPRIETARY INFORMATION OF

BOSE CORPORATION WHICH IS BEING FURNISHED ONLY FOR

THE PURPOSE OF SERVICING THE IDENTIFIED BOSE PRODUCT

BYAN AUTHORIZED BOSE SERVICE CENTER OR OWNER OF

THE BOSE PRODUCT, AND SHALL NOT BE REPRODUCED OR

USED FOR ANY OTHER PURPOSE.

The Bose Panaray MA12 Modular Line Array Loudspeaker System is covered by a limited

5-year transferable limited warranty.

Warranty

Contents

Warranty.............................................................................................................................................2

Specifications....................................................................................................................................3

Product Description..........................................................................................................................3

Accessories Used with the MA12 Loudspeaker System...............................................................3

Part List Notes...................................................................................................................................3

Packaging Part List, Panaray®MA12 Loudspeaker System (see Figure 1) .................................4

Figure 1. Panaray MA12 Loudspeaker Packaging View ..................................................................4

Main Part List, Panaray MA12 Loudspeaker System (see Figure 2) ............................................5

Figure 2. Panaray MA12 Loudspeaker System Exploded View .......................................................6

Part List, Panaray MA12 Loudspeaker Protection Circuit Board (see Figure 3).........................7

Figure 3. MA12 Protection Circuit Board Layout Diagram................................................................7

Figure 4. Panaray MA12 Loudspeaker Wiring Diagram...................................................................8

Disassembly Procedures .................................................................................................................9

Test Procedures ..............................................................................................................................10

Figure 5. Panaray MA12 Test Setup Diagram ................................................................................10

Service Manual Revision History...................................................................................................11

Specifications

External Dimensions: 38.5 x 4.2 x 5.1 in. (978 x 107 x 130 mm)

Weight: Single Speaker: 22 lb. (10 kg)

Packed System: 24 lb. (11 kg)

Sensitivity: 88dB SPL, 120 Hz - 15 kHz (1W/1m free space)

System Protection: PTC, lamp

Impedance: 8 Ohms nominal, 7.5 Ohms minimum

Power Handling: 300 Watts continuous per IEC-268-5, 120 Hz high pass,

96 hours. Recommended amplifier power 150-300 Watts

Product Description

The Bose®Panaray®MA12 Modular Line Array Loudspeaker System is a modular system used

for mid/high frequency sound reproduction. It is a vented enclosure design using 12 full range

drivers housed in a closely spaced line.

The loudspeaker provides a means for mechanical attachment of two units to form a rigid single

line source by using the CB-MA12 coupling bracket (see table below). Each loudspeaker has

two Neutrik®connectors and one barrier style terminal so that multiple units can be connected

as a system in series and parallel.

The Bose Panaray MA12 Loudspeaker can be used with the Bose Panaray MB4 Modular Bass

Loudspeaker for dynamic full range reproduction.

Description

Product Code

Black White

WB-MA12 wall mount bracket (0º – 10º pitch) 028333 028334

WBP-MA12 wall mount bracket (0º – 10º pitch, +/- 90º yaw) 028673 028674

CB-MA12 coupling bracket 028337 028338

PSA-12 stand adapter 029229 -

CVT-12 70V/100V transformer (non-RoHS complaint) 029388 029389

CVT-12 70V/100V transformer (RoHS complaint) 040190 040191

Accessories Used with the MA12 Loudspeaker System

Part List Notes

1. This part is not normally available from Customer Service. Approval from the Field Service

Manager is required before ordering.

2. The individual parts located on the PCBs are listed in the Electrical Part List.

3. This part is critical for safety purposes. Failure to use a substitute replacement with the

same safety characteristics as the recommended replacement part might create shock, fire

and/or other hazards.

4. This part is referenced for informational purposes only. It is not stocked as a repair part. Refer

to the next higher assembly for a replacement part.

Figure 1. Panaray MA12 Loudspeaker Packaging View

Packaging Part List

Panaray®MA12 Loudspeaker System (see Figure 1)

Item

Number

Description Bose

Part

Number

Vendor Part

Number

Qty. Note

1 PACKING, END CAP 263624 1490-7393-0 2

2 POLYBAG N/A 1497-5102-0 1

3 MA12 LOUDSPEAKER REF REF 1

4 PACKING, CENTER 263625 1490-7433-1 1

5 OWNER’S MANUAL 263626 4301-5191-0 1

6 CARTON 263572 145A7780-0 1

ESOB

Main Part List

Panaray®MA12 Loudspeaker System (see Figure 2)

Part NumberItem

Number

Description

Black White

Qty

Note

1 SCREW, CONNECTOR, M3x13 - - 4 4

2 CONNECTOR, NEUTRIK 298548 298548 2

3 GASKET, ENDCAP 259133 259133 2

4 SCREW, ENDCAP, M3.5x13 - - 12 4

5 ENDCAP 259132-001 259132-002 2

6 GASKET, DRIVER 298549 298549 12

7 DRIVER, 2.25” 298550 298550 12

8 SCREW, BAFFLE, M4.5x12 - - 16 4

9 SCREW, DRIVER, M3.5x8 - - 48 4

10 U-CHANNEL, GRILLE - - 2M 4

12 LOGO, BOSE 298552-001 298552-002 1

11 GRILLE 298551-001 298551-002 1

13 U-CHANNEL FOR GRILLE COVER - - .35M

14 GRILLE TRIM - - 2 4

15 BARRIER TERMINAL - - 1 4

16 SCREW, BARRIER TERMINAL,

M3x14 - - 2 4

- CVT-12 TRANSFORMER

(ACCESSORY ITEM) 040190 040191 1

Figure 2. Panaray®MA12 Loudspeaker System Exploded View

11 2

Part List

Panaray®MA12 Loudspeaker Protection Circuit Board (see Figure 3)

Figure 3. MA12 Protection Circuit Board Layout Diagram





Item

Number

Description Part Number Qty. Note

PCB ASSY, PROTECTION CKT 298553 1

1 LAMP, GREEN DOT 298554 2

2 POLYSWITCH, RXE075 298555-075 1

Figure 4. Panaray®MA12 Loudspeaker Wiring Diagram

PTC

LAM

LAMP

Screw

Terminal

Disassembly Procedures

Note: Refer to the figure below for the

following procedures.

1. End Cap Removal

1.1 Using a Phillips-head screwdriver,

remove the six screws (4) that secure the

steel end cap (5) to the housing and grille

trim.

1.2 Gently pull the end cap away from the

housing.

Re-assembly Note: When replacing the end

cap, ensure that it is fully seated against the

housing for an airtight seal. Replace all six

screws to prevent air leaks.

2. Grille Assembly Removal

2.1 Remove the two screws at the front of

each end cap.

2.2 Take the grille trim (14) along with the U-

rubber channel (13) away from the end of

the grille (11).

2.3 Gently pull the grille assembly away

from the housing. Be careful not to mark

the surface of the grille or the housing.

3. Driver Removal

3.1 Perform procedure 2.

3.2 Using a Phillips-head screwdriver,

remove the sixteen screws (8) that secure

the baffle to the housing.

3.3 Lift the baffle with the six drivers (7) out

of the housing.

3.4 Unplug the driver cable wires from the

driver you wish to remove.

3.5 Using a Phillips-head screwdriver,

remove the four screws (9) that secure the

driver to the baffle. Lift out the driver.

11 2

Test Procedures

1. Air Leak Test

1.1 Set up the system for test as shown in

Figure 5.

1.2 Apply a 100 Hz, 10 Vrms sine wave to

the input connectors.

1.3 Listen carefully for any air leaks from

around the end cap, drivers and the baffle.

Air leaks will be heard as a hissing or sput-

tering sound. All repairs must be hidden.

Test duration should be 5 seconds minimum.

2. Rub and Tick Test

2.1 Perform disassembly procedure 3. It is

not necessary to unplug the wires at the

driver assembly terminals.

2.2 Connect a signal generator directly to

the terminals of the driver under test.

2.3 Apply a 20 Hz, 5 Vrms sine wave to the

driver assembly.

2.4 Listen carefully for any extraneous

noises, such as rubbing, scraping or ticking.

Note: To distinguish between normal sus-

pension noise and rubs or ticks, displace the

cone slightly with your fingers.

If the noise stays the same, it is normal

suspension noise and the driver is fine.

Suspension noise will not be heard with

program material.

3. Phase Test

3.1 Momentarily apply 10 VDC to the loud-

speaker input connector. Apply the positive

to pin “1+” and the negative to pin “1-” of the

Neutrik®connector.

3.2 When applying the DC voltage level,

observe the driver cones. They should all

move outward when the DC level is applied.

3.3 Rewire any incorrectly wired driver.

4. System Sweep Test

4.1 Set up the system for test as shown in

Figure 5.

4.2 Apply a 10 Hz, 10 Vrms sine wave to the

loudspeaker input connector.

4.3 While listening to the output of the

system, sweep the input frequency slowly

from 10 Hz to 20 kHz.

4.4 Listen carefully for any extraneous

noises such as buzzing or ticking.

Power Amplifier

INPUT OUTPUT

Audio Signal

Generator

Figure 5. Panaray®MA12 Test Setup Diagram

Service Manual Revision History

Date Revision

Level

Description of Change Change Driven

Pages

Affected

1/02 00 Document released at revision 00. Service manual

release All

10/06 01 Added RoHS compliant part numbers. RoHS initiative 4, 6

Autres manuels pour Panaray MA12

Table des matières

Autres manuels Bose Système de haut-parleurs

Bose

Bose Videobar VB1 Manuel utilisateur

Bose

Bose 10.2 Series II Manuel utilisateur

Bose

Bose 201 Series Manuel utilisateur

Bose

Bose 501 Series IV Manuel utilisateur

Bose

Bose Acoustimass 500 Manuel utilisateur

Bose

Bose Soundbar 500 Manuel utilisateur

Bose

Bose VCS-10 Manuel utilisateur

Bose

Bose Solo TV Sound Manuel utilisateur

Bose

Bose Freestyle Speaker System Manuel utilisateur

Bose

Bose L1 Pro Series Manuel d'utilisation et d'entretien

Bose

Bose 901 Series VI Loud Manuel utilisateur

Bose

Bose 901 Series III Manuel utilisateur

Bose

Bose 901 Series II Manuel utilisateur

Bose

Bose 501 Series III Manuel utilisateur

Bose

Bose 601 Series IV Direct/Reflecting Manuel utilisateur

Bose

Bose 10.2 Stereo Everywhere Manuel utilisateur

Bose

Bose F1 Model 812 Passive Manuel utilisateur

Bose

Bose SMART Soundbar 600 Manuel utilisateur

Bose

Bose 201 Series Manuel utilisateur

Bose

Bose L1 Model II Guide de l'utilisateur

Bose

Bose L1 Pro Series Manuel d'utilisation et d'entretien

Bose

Bose Bundle Manuel utilisateur

Bose

Bose L1 Model II Mode d’emploi

Bose

Bose Soundbar 500 Manuel utilisateur

Manuels Système de haut-parleurs populaires d'autres marques

JVC

JVC CA-MXK5R Manuel utilisateur

LG NB4532B Manuel utilisateur

JVC

JVC CA-FSH100 Manuel utilisateur

5Core

5Core Pro Series Manuel utilisateur

EAW

EAW MQV1394e Manuel utilisateur

Lynx

Lynx GXR-LA10A Manuel utilisateur

iLive

iLive ITB066B Manuel utilisateur

RDX

RDX QuickStation 4 Manuel utilisateur

Electro-Voice

Electro-Voice S-122 Manuel utilisateur

Sven

Sven SPS-619 GOLD Manuel utilisateur

Pioneer

Pioneer CS-7070 Manuel utilisateur

EAW

EAW UB82e Manuel utilisateur

Sondpex

Sondpex Active Speaker System and Digital Music... Manuel utilisateur

JVC

JVC NX-PN7 Manuel utilisateur

Marshall Amplification

Marshall Amplification AR-DM61-BT Manuel utilisateur

Yamaha

Yamaha NX-A01 - Speaker Sys Manuel utilisateur

SE Audiotechnik

SE Audiotechnik I-LINE Manuel utilisateur

Gemini

Gemini WRX-843 Series Manuel utilisateur