Bosch C1050ES Manuel de référence

Technical Service Bulletin:

Replacing The Control Unit

Models: C1050ES, C950ES, 940ES, 940ESO, 830ES

Introduction

Tools needed:

Phillips head screw driver

Small flat head screw driver

Needle-nosed pliers

Note: Avoid touching printed circuit board (PCB) as static discharge

may damage circuitry.

Preparation

Push power button to "OFF" and unplug power cord.

Loosen two Phillips head screws on bottom rear of front cover.

Pull cover bottom outwards then lift cover upwards to remove.

Removing control unit

Remove three Phillips screws on front of control unit. (Fig. 2,

pos. 1)

Turn control unit to expose the rear. (Fig. 2, pos. 2).

Locate and remove 6 Phillips head screws on back of control

unit (Fig. 2, pos. 3).

control unit front

Figure 2

Remove rear cover from control unit to expose circuit board

electrical connections. Slide wire restraints out of control unit.

(Fig. 3, pos. 1).

Remove two large electrical strip connectors by pulling them

away from board. (Fig. 3, pos. 2).

Remove medium sized electrical strip connector by pulling it

outwards. (Fig. 3, pos. 3).

Remove small electrical strip connector by pulling it outwards.

(Fig. 3, pos. 4).

Remove two large ignition wires by pulling them outwards. (Fig.

3, pos. 5).

Remove yellow/green striped ground wire spade connection by

depressing tab on connector and pulling it gently off the board.

(Fig. 3, pos. 6).

Loosen two small flat head screws on terminal block for power

cord. Pull black and white wires free from terminal block and

control unit. (Fig. 3, pos. 7).

Loosen Phillips head screw and remove green ground wire con-

nection for power cord. (Fig. 3, pos. 8).

Figure 3

1 1

Remove control unit from the water heater.

Appliance evaluation for PCB jumper location

Please evaluate the following prior to installation of the replacement

PCB:

|Replacing The Control Unit Technical Service Bulletin

Data subject to change without notice | Printed in the USA | BTC 740002317 C | 06.2012 Bosch Thermotechnology Corp.

Locate rating plate sticker on right side of heater cover.

Determine model number (Fig.1, pos.A) and gas type (Fig.1,

pos.B).

Figure 1

Locate hot water outlet pipe (Fig.2, pos.A). Determine the type

of outlet temperature sensor installed on the hot water outlet

pipe (Fig.3).

Figure 2

Figure 3

Surface mount outlet

temperature sensor

Immersed outlet

temperature sensor

PCB jumper installation

In order for the appliance to work correctly, the proper jumpers

must be installed on the PCB board. (Fig.4)

Backside of control unit

ackside o

control uni

Figure 4

Based on your model, gas type and type of outlet temperature

sensor, jumpers should be installed on the PCB in the following

arrangement:

C 950 ES or 830 ES with surface mount outlet temperature

sensor

Natural

Gas

atura

Gas

Figure 5

Liquid

Propane

C 950 ES or 830 ES with immersed outlet temperature sensor

Figure 6

JUMPER

NEEDED

Natural

Gas

Liquid

Propane

|Replacing The Control Unit Technical Service Bulletin

Data subject to change without notice | Printed in the USA | BTC 740002317 C | 06.2012 Bosch Thermotechnology Corp.

Bosch Thermotechnology Corp.

50 Wentworth Avenue

Londonderry, NH 03053

Tel: 1-800-283-3787

Fax: 1-603-965-7581

www.bosch-climate.us

C 1050 ES or 940 ES/ESO with surface mount outlet

temperature sensor

Figure 7

Natural

Gas

Liquid

Propane

C 1050 ES or 940 ES/ESO with immersed outlet temperature

sensor

Figure 8

Natural

Gas

Liquid

Propane

Replacing control unit

Once the appropriate jumpers have been determined, remove

rear cover of replacement control unit.

Install jumpers in the proper location on PCB.

Connect green ground wire from power cord to replacement

control board with Phillips head screw. (Fig. 3, pos. 8).

Reconnect black and white power cord wires to terminal

block on replacement control unit; Black -L (Load), White - N

(Neutral). Secure to terminal block by tightening flat head

screws. (Fig. 3, pos. 7).5. Reconnect yellow/green striped

ground wire to spade connection on replacement control

board. (Fig. 3, pos. 6).

Reattach large ignition wires to replacement control board (no

polarity). (Fig. 3, pos. 5).

Reconnect small electrical strip connector to replacement

control board. (Fig. 3, pos. 4).

Reconnect medium sized electrical strip connector to

replacement control board. (Fig. 3, pos. 3).

Reconnect two large electrical strip connectors to replacement

control board. (Fig. 3, pos. 2).

Reseat rubber wire restraints in control unit. (Fig. 3, pos. 1).

Replace rear cover on unit using 6 Phillips screws. (Fig. 2, pos.

3).

Place control unit back into water heater and secure with 3

Phillips head screws. (Fig. 2, pos. 1).

Plug water heater power cord back into electrical outlet and

push On/Off button on water heater to "ON".

Autres manuels pour C1050ES

Ce manuel convient aux modèles suivants

Autres manuels Bosch Chauffe-eau

Bosch

Bosch Highflow 17e Manuel utilisateur

Bosch

Bosch GWH 2700 ES LP Manuel utilisateur

Bosch

Bosch W 125 T1 Manuel d'installation et d'exploitation

Bosch

Bosch TR2000T Series Manuel d'utilisation

Bosch

Bosch C 1210 ESC Manuel de référence

Bosch

Bosch AQ 125BO LP Manuel utilisateur

Bosch

Bosch WH36 Document technique

Bosch

Bosch 330-PN-N Manuel utilisateur

Bosch

Bosch GWH 10-2 G Series Document technique

Bosch

Bosch AquaStar 125HX NG Manuel utilisateur

Bosch

Bosch OptiFlow Professional GWH12 1 CTD E23 Manuel utilisateur

Bosch

Bosch Tronic 3000 C Pro US12 Manuel utilisateur

Bosch

Bosch BC2600RA Manuel utilisateur

Bosch

Bosch W 325 K**T1 Manuel du propriétaire

Bosch

Bosch TR5000R 24/27 EB Manuel utilisateur

Bosch

Bosch TR1500TOR 5 T Manuel utilisateur

Bosch

Bosch Evolution 500 Series Manuel de référence

Bosch

Bosch AQ 125BO NG Manuel utilisateur

Bosch

Bosch 10P Manuel

Bosch

Bosch Tronic 5000 Series Manuel utilisateur

Bosch

Bosch Model GWH 425 Manuel utilisateur

Bosch

Bosch TR7000 Series Manuel utilisateur

Bosch

Bosch BSS250E-2 Manuel utilisateur

Bosch

Bosch Tronic 4000 Manuel utilisateur

Manuels Chauffe-eau populaires d'autres marques

Kenmore

Kenmore 153.582400 Manuel utilisateur

Applimo

Applimo Edel AIR Manuel utilisateur

STIEBEL ELTRON

STIEBEL ELTRON Eltronom SHU 5 S Manuel utilisateur

clage

clage E-Mini Series Manuel utilisateur

Toyotomi

Toyotomi Oil Miser OM-180 Manuel utilisateur

Bradford White

Bradford White EF Series Manuel utilisateur

Eccotemp

Eccotemp 40-H Manuel utilisateur

Dimplex

Dimplex ECSd125-580 Mode d’emploi

Dux

Dux 32FCR6N Manuel utilisateur

Toyotomi

Toyotomi Oil Miser OM-148 (Type D) Guide de dépannage

Noritz

Noritz N-132M Manuel d'instructions

TESY

TESY GCV7/4S 10047 Fiche technique

A.O. Smith

A.O. Smith Gphe 50 Manuel utilisateur

Koryo

Koryo KWHZF15Y Manuel utilisateur

Pentair

Pentair PSC-14-4-02 Manuel utilisateur

GE 40M06AAG Instructions de montage

Thermor

Thermor AEROMAX SPLIT 2 Manuel utilisateur

American Hometec

American Hometec AHQ-B03X Manuel utilisateur