Bosch Evolution 500 Series Manuel de référence

Models: 715ES, C800ES, 2400ES, 2700ES, Evolution 500, Integra 500

Replacing the control unit

Service Bulletin G3-24

Introduction

Tools needed:

Phillips head screw driver

Small flat head screw driver

Needle-nosed pliers

Note: Avoid touching printed circuit board (PCB) as static discharge

may damage circuitry.

Preparation

Push power button to “OFF” and unplug power cord.

Loosen two Phillips head screws on bottom rear of front cover.

Pull cover bottom outwards then lift cover upwards to remove.

Removing control unit

Remove three Phillips screws on front of control unit. (Fig. 2,

pos. 1)

Turn control unit to expose the rear. (Fig. 2, pos. 2).

Locate and remove 6 Phillips head screws on back of control

unit (Fig. 2, pos. 3).

control unit front

Figure 2

Remove rear cover from control unit to expose circuit board

electrical connections. Slide wire restraints out of control unit.

(Fig. 3, pos. 1).

Remove two large electrical strip connectors by pulling them

away from board. (Fig. 3, pos. 2).

Remove medium sized electrical strip connector by pulling it

outwards. (Fig. 3, pos. 3).

Remove small electrical strip connector by pulling it outwards.

(Fig. 3, pos. 4).

Remove two large ignition wires by pulling them outwards.

(Fig. 3, pos. 5).

Remove yellow/green striped ground wire spade connection by

depressing tab on connector and pulling it gently off the board.

(Fig. 3, pos. 6).

Loosen two small flat head screws on terminal block for power

cord. Pull black and white wires free from terminal block and

control unit. (Fig. 3, pos. 7).

Loosen Phillips head screw and remove green ground wire con-

nection for power cord. (Fig. 3, pos. 8).

Figure 3

1 1

Remove control unit from the water heater.

Appliance evaluation for PCB jumper location

Please evaluate the following prior to installation of the replacement

PCB:

|G3-24 | 715ES, C800ES, 2400ES, 2700ES, Evolution 500, Integra 500 Service bulletin

Data subject to change without notice | Printed in the USA | BTC 710002318 D | 06.2012 Bosch Thermotechnology Corp.

Bosch Thermotechnology Corp.

50 Wentworth Avenue

Londonderry, NH 03053

Tel: 1-800-642-3111

Fax: 1-603-965-7581

www.bosch-climate.us

Locate rating plate sticker on right side of heater cover.

Determine model number (Fig.1, pos.A) and gas type (Fig.1,

pos.B).

Figure 1

PCB jumper installation

In order for the appliance to work correctly, the proper jumpers

must be installed on the PCB board. (Fig.4)

Backside of control unit

ackside o

control uni

Figure 4

Based on your model and gas type, jumpers should be installed

on the PCB in the following arrangement:

Model 2400 ES:

Natural

Gas

atura

Gas

Figure 5

Liquid

Propane

Models: C 1050 ES, 940 ES/ESO, 2700 ES, C 800 ES, 715 ES,

Evolution 500 (WTD 27), or Integra 500 (WTD 30)

Figure 7

Natural

Gas

Liquid

Propane

Replacing control unit

Once the appropriate jumpers have been determined, remove

rear cover of replacement control unit.

Install jumpers in the proper location on PCB.

Connect green ground wire from power cord to replacement

control board with Phillips head screw. (Fig. 3, pos. 8).

Reconnect black and white power cord wires to terminal

block on replacement control unit; Black -L (Load), White - N

(Neutral). Secure to terminal block by tightening flat head

screws. (Fig. 3, pos. 7).5. Reconnect yellow/green striped

ground wire to spade connection on replacement control

board. (Fig. 3, pos. 6).

Reattach large ignition wires to replacement control board (no

polarity). (Fig. 3, pos. 5).

Reconnect small electrical strip connector to replacement con-

trol board. (Fig. 3, pos. 4).

Reconnect medium sized electrical strip connector to replace-

ment control board. (Fig. 3, pos. 3).

Reconnect two large electrical strip connectors to replacement

control board. (Fig. 3, pos. 2).

Reseat rubber wire restraints in control unit. (Fig. 3, pos. 1).

Replace rear cover on unit using 6 Phillips screw (Fig. 2, pos.3).

Place control unit back into water heater and secure with 3

Phillips head screws. (Fig. 2, pos. 1).

Plug water heater power cord back into electrical outlet and

push On/Off button on water heater to “ON”.

Ce manuel convient aux modèles suivants

Autres manuels Bosch Chauffe-eau

Bosch

Bosch GWH 450 ESR-L Manuel utilisateur

Bosch

Bosch TRONIC 5000C Pro Document technique

Bosch

Bosch Therm 6000 S Manuel utilisateur

Bosch

Bosch Pro Tankless GWH-425-HNO-N Manuel utilisateur

Bosch

Bosch TRONIC 6000C WH17 Document technique

Bosch

Bosch US3 Document technique

Bosch

Bosch Stora SWDP 200-2 Guide rapide

Bosch

Bosch 330-PN-N Manuel utilisateur

Bosch

Bosch GWH 715 ES Manuel utilisateur

Bosch

Bosch Comfort Plus TR 4000 Manuel utilisateur

Bosch

Bosch Tronic 5000C Manuel de référence

Bosch

Bosch TR5000R 18/21 EB Manuel utilisateur

Bosch

Bosch WR430-3K Manuel du propriétaire

Bosch

Bosch TR4000 Manuel utilisateur

Bosch

Bosch GWH C 920 ES Manuel de référence

Bosch

Bosch 830ES Manuel de référence

Bosch

Bosch TR5500T Series Manuel utilisateur

Bosch

Bosch WR8 series Document technique

Bosch

Bosch T2400S 8 ND 23 Instructions d'utilisation et d'installation

Bosch

Bosch Therm 6000 S Manuel utilisateur

Bosch

Bosch BC3200RABC3200RA5 Manuel utilisateur

Bosch

Bosch TF250 Document technique

Bosch

Bosch BC2600RA Manuel utilisateur

Bosch

Bosch Pro Tankless GWH-450-ES Series Manuel utilisateur

Manuels Chauffe-eau populaires d'autres marques

Kenmore

Kenmore 153.582400 Manuel utilisateur

Applimo

Applimo Edel AIR Manuel utilisateur

STIEBEL ELTRON

STIEBEL ELTRON Eltronom SHU 5 S Manuel utilisateur

clage

clage E-Mini Series Manuel utilisateur

Toyotomi

Toyotomi Oil Miser OM-180 Manuel utilisateur

Bradford White

Bradford White EF Series Manuel utilisateur

Eccotemp

Eccotemp 40-H Manuel utilisateur

Dimplex

Dimplex ECSd125-580 Mode d’emploi

Dux

Dux 32FCR6N Manuel utilisateur

Toyotomi

Toyotomi Oil Miser OM-148 (Type D) Guide de dépannage

Noritz

Noritz N-132M Manuel d'instructions

TESY

TESY GCV7/4S 10047 Fiche technique

A.O. Smith

A.O. Smith Gphe 50 Manuel utilisateur

Koryo

Koryo KWHZF15Y Manuel utilisateur

Pentair

Pentair PSC-14-4-02 Manuel utilisateur

GE 40M06AAG Instructions de montage

Thermor

Thermor AEROMAX SPLIT 2 Manuel utilisateur

American Hometec

American Hometec AHQ-B03X Manuel utilisateur