Bosch VG5 600 Series Manuel utilisateur

AutoDome 600 Series Analog PTZ Cam-

era

VG5 600 Series

en User Manual

AutoDome 600 Series Analog PTZ Camera Table of Contents | en 3

Bosch Security Systems, Inc. User Manual F.01U.270.005 | 2.0 | 2012.06

Table of Contents

1 Getting Started 5

1.1 Powering On 5

1.2 Establishing AutoDome Control 5

1.2.1 Basic Keyboard Operation 6

1.2.2 Keyboard Commands 6

1.3 Setting the Camera Address 7

1.3.1 FastAddress 7

1.4 Setting Passwords 8

1.4.1 Special Passwords 8

2 On-Screen Display Menu Navigation 9

2.1 Setup Menu 9

2.2 Camera Setup Menu 10

2.3 Lens Setup 12

2.4 PTZ Setup Menu 13

2.5 Display Setup Menu 15

2.6 Communication Setup Menu 17

2.7 Alarm I/O Setup 18

2.8 Rule Setup Menu 20

2.9 Language Menu 22

2.10 Advanced Feature Setup Menu 22

2.11 Diagnostics Menu 23

2.11.1 Alarm Status Submenu 25

3 Common AutoDome User Commands (unlocked) 26

3.1 Setting AutoPan Mode 26

3.2 Setting Preset Shots 26

3.3 Specifying a Shot or a Sector Title 27

3.4 Configuring Preposition Tours 27

3.5 Programming the Inactivity Operation 28

3.6 Recording Tours 28

4 Alternative Control Protocols 29

4.1 Setting FastAddress with Alternative Protocols 29

4.1.1 Using an American Dynamics Controller 29

4.1.2 Using a Pelco Controller 32

4.2 Pelco Protocol Mode 33

4.2.1 Hardware Configuration 33

4.2.2 Pelco Keyboard Commands 34

4.2.3 Pelco Keyboard Commands 34

4.2.4 Special Preset Commands 35

5 Pelco On-Screen Menus 36

5.1 Setup Menu 36

5.1.1 Command Lock (locked) 37

4en | Table of Contents AutoDome 600 Series Analog PTZ Camera

F.01U.270.005 | 2.0 | 2012.06 User Manual Bosch Security Systems, Inc.

5.1.2 Bosch Menu (locked) 37

5.1.3 PTZ Setup (unlocked) 38

5.1.4 Other Menus 39

6 Keyboard Commands by Number 40

7 Advanced Features 44

7.1 Alarm Rules 44

7.1.1 Controlling Alarm Rules 44

7.1.2 Alarm Rule Examples 44

7.2 AutoTrack Operation 48

7.2.1 AutoTrack Settings and Recommendations 48

7.2.2 AutoTrack Optimization 49

7.3 Virtual Masking 50

7.4 Privacy Masking 50

7.5 Motion Detection with Region of Interest

(Preset positions 90 through 99)51

7.6 Image Stabilization 51

7.7 Pre-position Tour 51

7.8 Azimuth, Elevation, and Compass Directions 52

7.8.1 Setting the Azimuth Zero Point 52

7.8.2 Displaying Azimuth, Elevation, and Compass Headings 53

7.9 AutoHome Recalibration Commands and Settings 53

7.9.1 AutoHome Recalibration Operation 54

7.9.2 Using the AutoHome Recalibration 54

8 Troubleshooting Guide 55

8.1 VG5 AutoDome Operation and Control 55

8.2 VG5 Series AutoDome Audio 59

9 User Command Table 62

A Appendix: FastAddress Conversions 64

Index 65

AutoDome 600 Series Analog PTZ Camera Ge t t i n g S t a r t e d | e n 5

Bosch Security Systems, Inc. User Manual F.01U.270.005 | 2.0 | 2012.06

1 Getting Started

Install and wire the AutoDome according to the VG5 AutoDome Installation Manual. A typical

system includes a keyboard, matrix switcher, monitor, and appropriate wiring connections.

Please refer to the individual product manuals for complete installation and setup instructions

for each of the system components.

1.1 Powering On

When you turn the AutoDome power on there is a ten (10) second pause before the dome

starts its homing phase. During the homing phase the camera pans left and right and tilts up

and down. It also adjusts the lens focus. The entire homing phase lasts approximately 40

seconds and ends with a firmware version screen.

Figure 1.1 Sample VG5 Startup Firmware Version Screen

The splash screen displays the type of AutoDome, the camera installed, the firmware levels for

various files, and the current IP address (for VG5 AutoDome 700 Series models).

1.2 Establishing AutoDome Control

The most common ways to interface with the AutoDome are:

– Using a keyboard and on-screen display (OSD) menus. This method is the most common

and is covered in this manual.

– Using the AutoDome Configuration Tool software running on a PC with Bilinx or the RS-

232/485 communication protocol. Refer to the CTFID User Manual for instructions.

– Using a PC-based graphical user interface (GUI) such as the Bosch DiBos 8 software.

Refer to the DiBos 8 User Guide for instructions.

Bosch Security Sys. AutoDome(r)

600 Series

Day/Night 36X

SC Boot

FPGA

VCA_boot

STD Comm

No Heater

FastAddress: Not Set

5.00.00.03/1.05.00.02

1.00.00.00

5.00.00.03

1.13.01.05

1.02.00.01

6en | Getting Started AutoDome 600 Series Analog PTZ Camera

F.01U.270.005 | 2.0 | 2012.06 User Manual Bosch Security Systems, Inc.

1.2.1 Basic Keyboard Operation

The following tables summarize the basic operations for a standard keyboard and the

functions available to control an AutoDome camera.

Table 1.1 Typical Keyboard Functions

Table 1.2 Typical Keyboard Controls for an AutoDome Camera

1.2.2 Keyboard Commands

Keyboard control commands are composed of a sequence of three (3) inputs with the

following convention: 1) a Function key + 2) a Command number key(s) + 3) the Enter key.

– Depending on the type of keyboard, the control function keys are labeled:

ON or AUX ON

OFF or AUX OFF

SET or SET SHOT

SHOT or SHOW SHOT

– Command numbers range from 1 to 999. See Section 6 Keyboard Commands by Number,

page 40 for a complete list of keyboard commands.

–TheEnter key can also be labeled with the ∞? symbol.

For example, the keyboard command to make the AutoDome pan 360º continuously is:

ON-1-ENTER (press the ON key, then press the number 1key, and then press ENTER.)

Typical Keyboard

Features

Usage

Function Keys Selects a specific control setting.

Number Keys Inputs a number from 0 to 9.

Camera Key Selects a camera number.

Enter Key Inputs a selection.

Focus Key Sets the lens focus or makes a menu selection in OSD mode.

Iris Key Sets the lens iris setting or makes a menu selection in OSD mode.

Key LEDs Indicates an active key.

LCD Displays the current status.

Joystick Controls a pan/tilt/zoom (PTZ) AutoDome camera.

Dome Operation How to control

To Pan Side to Side Move the joystick left or right.

To Tilt Up and Down Move the joystick forward and back.

To Zoom In Twist the joystick clockwise.

To Zoom Out Twist the joystick counterclockwise.

NOTICE!

The convention used for control key commands in this manual is ON, OFF, SET, and SHOT.

Refer to your keyboard manual for the key naming conventions.

AutoDome 600 Series Analog PTZ Camera Ge t t i n g S t a r t e d | e n 7

Bosch Security Systems, Inc. User Manual F.01U.270.005 | 2.0 | 2012.06

1.3 Setting the Camera Address

Once the AutoDome power is turned on and homing is complete, you must set the camera

address. You may also want to assign a password and customize some of the AutoDome

default settings.

1.3.1 FastAddress

FastAddress is an AutoDome feature that allows you to set or change a camera address using

the keyboard and on-screen menus.

There are three (3) FastAddress commands:

–ON-999-ENTER: Displays and programs all cameras without an address in the system.

–ON-998-ENTER: Displays and programs all cameras with or without an address in the

system.

–ON-997-ENTER: Displays the current address status of all cameras in the system

simultaneously.

To set an address for a camera without an address:

1. Select the camera number you want to FastAddress. The system displays the camera

number on the keyboard and the image on the corresponding monitor.

2. Press #-ENTER (where #is the camera number without an address).

3. Press ON-999-ENTER to invoke an on-screen display of cameras on the system without

an address.

4. Follow the on-screen instructions. You receive an on-screen confirmation when the

FastAddress is complete.

To change or clear an address for a camera with an address:

1. Select the camera number you want to FastAddress. The system displays the camera

number on the keyboard and the image on the corresponding monitor.

2. Press #-ENTER (where #is the camera number with an address).

3. Press ON-998-ENTER to invoke an on-screen display of all cameras on the system, with or

without an address.

4. Follow the on screen instructions. You receive an on-screen confirmation when the

FastAddress is complete.

NOTICE! You do not need to set a camera address if using Bilinx or Ethernet communication.

See the VG5 AutoDome Installation Manual to configure an AutoDome for Bilinx or Ethernet

operation.

NOTICE! If a keyboard is set to a camera number that already has an address, that camera

also responds to this command.

NOTICE!

FastAddress is stored in nonvolatile memory and does not change if the power is turned off or

if the default settings are restored.

8en | Getting Started AutoDome 600 Series Analog PTZ Camera

F.01U.270.005 | 2.0 | 2012.06 User Manual Bosch Security Systems, Inc.

1.4 Setting Passwords

Passwords are used to control access to locked command menus. Unlocked commands are

available to all users. Passwords are four (4) digits in length.

1.4.1 Special Passwords

To set or change a password (locked command):

1. Press OFF-90-ENTER to turn off the command lock.

2. Press SET-802-ENTER to access the password menu.

3. Tilt the joystick up or down to choose a number. Tilt the joystick right to move to the next

number position.

4. Follow the on-screen instructions and save the password. You receive an on-screen

confirmation.

Password Security Level

0000 (default) Enables security and requires a user to enter the unlock command

OFF-90-ENTER before invoking a locked command.

9999 Disables all security and allows all users to access locked commands.

AutoDome 600 Series Analog PTZ Camera On-Screen Display Menu Navigation | en 9

Bosch Security Systems, Inc. User Manual F.01U.270.005 | 2.0 | 2012.06

2 On-Screen Display Menu Navigation

The AutoDome is programmed through the on-screen display (OSD) menus. To access the

OSD menus, you must open the main Setup Menu.

Menu items marked with an asterisk (*) are default settings, unless otherwise noted.

2.1 Setup Menu

The main Setup Menu provides access to all programmable AutoDome settings. It is a locked

menu that requires the user to turn off the command lock.

To open the main Setup Menu (locked command):

1. Press OFF-90-ENTER to turn off the command lock.

2. Press ON-46-ENTER to access the Main Menu.

3. Use the joystick to highlight a menu item.

4. Press Focus/Iris to open a menu.

5. Follow the on-screen instructions.

NOTICE!

After a period of 4.5 minutes of inactivity, a menu times-out and exits without warning. Some

unsaved settings in the current menu can be lost.

NOTICE!

The AutoDome displays only those menus applicable to the particular AutoDome Series

configuration. Use the joystick to navigate through the menu and the Focus/Iris keys to make

a selection.

Setup Menu

Exit...

Camera Setup

Lens Setup

PTZ Setup

Display Setup

Communication Setup

Alarm Setup

Language

Advanced

Diagnostics

Focus / Iris: Select

10 en | On-Screen Display Menu Navigation AutoDome 600 Series Analog PTZ Camera

F.01U.270.005 | 2.0 | 2012.06 User Manual Bosch Security Systems, Inc.

Setup Menu Choices:

2.2 Camera Setup Menu

The Camera Setup Menu provides access to camera settings that can be changed or

customized. Menu items marked with an asterisk (*) are the default settings.

Menu Description

Exit Exits the menu.

Camera Setup Accesses adjustable camera settings such as: white balance, gain,

sharpness, sync, line lock, backlight, shutter, and night mode.

Lens Setup Accesses adjustable lens settings such as: focus, iris, zoom speed, and

digital zoom.

PTZ Setup Accesses adjustable pan/tilt/zoom (PTZ) settings such as: Autopan, tours,

PTZ speed, inactivity period, AutoPivot, and tilt limits.

Display Setup Accesses adjustable display settings such as: OSD, sector blanking, and

privacy masking.

Communication

Setup

Accesses communication settings such as: AutoBaud and Bilinx.

Alarm Setup Accesses the alarm settings such as: inputs, outputs, and rules.

Language Displays the language.

Advanced Accesses the advanced features menu including Stabilization, AutoTrack

Sensitivity, Camera Height, and Virtual Masking.

Diagnostics Displays the status of diagnostic events.

NOTICE!

To select the Exit Menu item from anywhere in the current menu, use the Zoom command.

Camera Setup

Exit...

* White Bal: EXT ATW

* Gain Control: AUTO

* Max. Gain Level: 6 (4**)

* Sharpness 12

* Synch Mode: Internal

* Line Lock Delay: 0

* Backlight Comp: OFF

*WDR OFF

* Shutter Mode: Auto SensUP

* Shutter: 1/60

* Auto SensUP Max: 15x

*NightMode: AUTO

* Night Mode Color: OFF

* Night Mode Threshold: 55

*Pre-Comp 1

Restore Defaults...

* = Factory Setting

** = WDR camera only

Focus / Iris: Select

Autres manuels pour VG5 600 Series

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Bosch Caméra de sécurité

Bosch

Bosch VDC?480 Series Manuel utilisateur

Bosch

Bosch VJR-821-ICCV Manuel utilisateur

Bosch

Bosch WZ45 Manuel utilisateur

Bosch

Bosch LTC-0498-21 Mode d’emploi

Bosch

Bosch MegaPixel NWC-0700 Manuel utilisateur

Bosch

Bosch VEZ Series Manuel

Bosch

Bosch FLEXIDOME HD 1080p VR Manuel utilisateur

Bosch

Bosch Dinion2X NBN-498 Manuel utilisateur

Bosch

Bosch MIC IP fusion 9000i Manuel utilisateur

Bosch

Bosch VG4 Series Manuel utilisateur

Bosch

Bosch VEI-Series Manuel utilisateur

Bosch

Bosch 200 Series Manuel utilisateur

Bosch

Bosch Diniop IP - NWC-0455 Manuel utilisateur

Bosch

Bosch VDC-445V03-20S Manuel utilisateur

Bosch

Bosch LTC 0610/11 Manuel utilisateur

Bosch

Bosch NDN-932 Manuel utilisateur

Bosch

Bosch VC86775T Manuel utilisateur

Bosch

Bosch NBN-63023-B Manuel utilisateur

Bosch

Bosch Divar DVR16E2302 Manuel utilisateur

Bosch

Bosch NBN-733 Manuel utilisateur

Bosch

Bosch DINION IP 8000 MP Manuel utilisateur

Bosch

Bosch VDI 230 Manuel utilisateur

Bosch

Bosch FLEXIDOME IP 3000i IR Manuel utilisateur

Bosch

Bosch WZ20NXV550‑0 Manuel utilisateur

Manuels Caméra de sécurité populaires d'autres marques

Okina USA

Okina USA SIR36-870VF650LP Manuel utilisateur

Divio

Divio NDR155PA Manuel utilisateur

Canon

Canon VB-C500D Manuel utilisateur

Easy Access

Easy Access EasyGuard Manuel utilisateur

Vivotek

Vivotek FD9389-EHV-v2 Manuel utilisateur

TUYA

TUYA COSMO W2 Manuel utilisateur

Eusso

Eusso UNC7500-IR Guide de configuration

urmet domus

urmet domus 1096/204 Manuel utilisateur

VC VC20 series Manuel utilisateur

Axis

Axis Q1614 Manuel utilisateur

ieGeek

ieGeek DD201 Manuel utilisateur

VADDIO

VADDIO ClearVIEW HD-USB PTZ 999-6990-000 Manuel utilisateur

Vicon

Vicon V662-D-1 Mode d'emploi

Grundig

Grundig GCH-K0274P Manuel utilisateur

Lorex

Lorex VANTAGE LBC7032 Manuel utilisateur

4xem

4xem WPT Manuel utilisateur

Samsung

Samsung SCV-3082 Manuel utilisateur

Vitek

Vitek VTC-C544 Manuel utilisateur