Bosch MegaPixel NWC-0700 Manuel utilisateur
1en | Bosch Security Systems Megapixel IP Cameras
F.01U.032.595 | V 1.0 | 2007.03 Quick Install Guide Bosch Security Systems
Important Safety Instructions
Type numbers: NWC-0700, NWC-0800, NWC-0900
Read, follow, and retain all of the following safety instructions. Heed all
warnings on the unit and in the operating instructions.
1. Clean only with a dry cloth. Do not use liquid cleaners or aerosol clean-
ers.
2. Do not install unit near any heat sources such as radiators, heaters,
stoves, or other equipment (including amplifiers) that produce heat.
3. Do not block any ventilation openings.
4. Do not use the unit near water or expose to rain or moisture. Never
spill liquid of any kind on the unit.
5. Unplug the unit during lightning storms or when unused for long peri-
ods.
6. Adust only those controls specified in the operating instructions.
7. Do not overload outlets and extension cords, as this can cause fire or
electrical shock.
8. Protect the plug and power cord from foot traffic or pinching, at elec-
trical outlets, and at its exit from the unit.
9. Operate the unit only from the type of power source indicated on the
label.
10. Unless qualified, do not attempt to service a damaged unit yourself.
Refer all servicing to qualified service personnel.
11. Use only replacement parts specified by the manufacturer.
12. Install in accordance with the manufacturer's instructions in accor-
dance with applicable local codes.
13. Use only attachments/accessories specified by the manufacturer.
Equipment change or modification could void the user's guarantee or
authorization agreement.
DANGER! High risk:
This symbol indicates an imminently hazardous situation such
as "Dangerous Voltage" inside the product.
If not avoided, this will result in an electrical shock, serious
bodily injury, or death.
!
WARNING! Medium risk:
Indicates a potentially hazardous situation.
If not avoided, this could result in serious bodily injury or death
!
CAUTION!
Indicates a potentially hazardous situation. If not avoided, this
may result in minor or moderate injury. Alerts the user to
important instructions accompanying the unit.
Megapixel IP Cameras Quick Install Guide | en 2
Bosch Security Systems Quick Install Guide F.01U.032.595 | V 1.0 | 2007.03
CAUTION!
Indicates a potentially hazardous situation.
If not avoided, this may result in property damage or risk of
damage to the unit.
i
NOTICE!
This symbol indicates information or a company policy that
relates directly or indirectly to the safety of personnel or
protection of property.
!
CAUTION!
– U.S.A. models only - Section 810 of the National Electrical
Code, ANSI/NFPA No. 70, provides information regarding
proper grounding of the mount and supporting structure,
location of discharge unit, connection to ground elec-
trodes, and requirements for the grounding electrode.
– Power lines: do not locate the camera near overhead
power lines, power circuits, electrical lights, or where it
may contact such power lines, circuits, or lights.
– Operate the unit only from the type of power source indi-
cated on the label. Before proceeding, be sure to discon-
nect the power from the cable to be installed into the unit.
– For external power supplied units, use only the rec-
ommended or approved power supplies.
–Forlimitedpowersourceunits, this power source
must comply with EN60950. Substitutions may dam-
age the unit or cause fire or shock.
– For 9-12 VDC units, voltage applied to the unit's
power input should not exceed 12.3 VDC. User-sup-
plied wiring must comply with local electrical codes
(Class 2 power levels). Do not ground the supply at
the terminals or at the unit's power supply terminals.
If unsure of the type of power supply to use, contact your
dealer or local power company.
i
NOTICE! You can view and print the full version of this
Installation Manual with Adobe Acrobat Reader, both provided
on the enclosed CD-ROM. This user guide is the intellectual
property of Bosch Security Systems; protected by copyright.
3en | Bosch Security Systems Megapixel IP Cameras
F.01U.032.595 | V 1.0 | 2007.03 Quick Install Guide Bosch Security Systems
FCC & ICES INFORMATION
(U.S.A. and Canadian Models Only)
This device complies with part 15 of the FCC Rules. Operation is subject to
the following conditions:
– this device may not cause harmful interference, and
– this device must accept any interference received, includ-
ing interference that may cause undesired operation.
The user may find the following booklet, prepared by the Federal Communi-
cations Commission, helpful: How to Identify and Resolve Radio-TV Interfer-
ence Problems. This booklet is available from the U.S. Government Printing
Office, Washington, DC 20402, Stock No. 004-000-00345-4.
i
NOTICE!
This equipment has been tested and found to comply with the
limits for a Class A digital device, pursuant to Part 15 of the
FCC Rules and ICES-003 of Industry Canada. These limits are
designed to provide reasonable protection against harmful
interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and radiates
radio frequency energy and, if not installed and used in accor-
dance with the instruction manual, may cause harmful interfer-
ence to radio communications. Operation of this equipment in a
residential area is likely to cause harmful interference, in which
case the user will be required to correct the interference at his
expense.
Intentional or unintentional modifications, not expressly
approved by the party responsible for compliance, shall not be
made. Any such modifications could void the user's authority to
operate the equipment. If necessary, the user should consult
the dealer or an experienced radio/television technician for cor-
rective action.
WARNING!
This is a class A product. In a domestic environment this
product may cause radio interference, in which case the user
may be required to take adequate measures.
Megapixel IP Cameras Quick Install Guide | en 4
Bosch Security Systems Quick Install Guide F.01U.032.595 | V 1.0 | 2007.03
1 Quick Install Guide
1.1 Camera installation using PoE switch
Equipment needed:
– PC with 100baseT or better network port
– 100 baseT or better network switch with PoE capability
–2CAT5Networkcables
1. Attach camera to a PoE port of the network switch with
CAT5 cable.
2. Attach (non-PoE) switch port to the PC LAN port with
CAT5 cable.
3. Manual iris lens: Check the lens to make sure the F-Stop is
between F2.8 and F4.0.
4. DC-iris lens: Ensure that the DC-iris cable is plugged into
the iris connector on the rear of the camera.
5. Plug in the switch's power cord.
6. A yellow LED on the back of the camera should light up
after a few seconds.
– This LED indicates that a link to the computer has
been established.
– A green LED will blink when the camera is accessed.
1.2 Camera installation with direct connection
to PC
Equipment needed:
– PC with 100baseT or better network port
– 1 CAT5 cross-linked network cable
– Power supply unit: 9-12 VDC, 500 mA.
!
CAUTION!
Never supply power via the Ethernet connection (PoE) when
power is already supplied via the power connector.
!
CAUTION!
For 9-12 VDC units, voltage applied to the unit's power input
should not exceed 12.3 VDC.
5en | Bosch Security Systems Megapixel IP Cameras
F.01U.032.595 | V 1.0 | 2007.03 Quick Install Guide Bosch Security Systems
1. Attach camera to the 100 Mbps network input of the PC
with the cross-link CAT 5 cable.
2. Manual iris lens: check the lens to make sure the F-Stop is
between F2.8 and F4.0.
3. DC-iris lens: plug in the DC-iris cable into the iris connec-
tor on the rear of the camera.
4. Plug in the camera power cord.
5. A yellow LED on the back of the camera should light up
after a few seconds.
– This LED indicates that a link to the computer has
been established.
– A green LED will blink when the camera is accessed.
1.3 Setting camera IP address
The camera is supplied with installation software on CD. The
installation software assists setting up the camera's IP address.
To run the installation software:
1. Make sure your Windows XP/2K account has administrative
privileges.
2. Using Windows Explorer, navigate to the CD and double
click the installer.exe file. The camera installer program
opens.
1.3.1 Configure firewall
As you start the application, your PC may prompt you to permit
its access to the network.
Allow the Camera Installer program to access the network.
1.3.2 Assigning IP addresses
Choosing between Basic or Advanced modes:
– Only use Basic mode (default) if the network does not
have other devices connected.
– Use Advanced mode if the network has other devices con-
nected (this is because using Automatic mode risks dupli-
cating existing IP addresses).
Megapixel IP Cameras Quick Install Guide | en 6
Bosch Security Systems Quick Install Guide F.01U.032.595 | V 1.0 | 2007.03
Basic mode
1. Click Automatic. The install program will scan the network
for all connected MegaPixel cameras and assign an IP
address automatically within the network segment of the
host PC.
When all the connected cameras show 'Success' in the
Results column, the installation process is complete.
2. Write down the (MAC) Ethernet address, corresponding IP
address, and installed location.
3. Click Save / Exit when done.
Fig. 1.1 Camera installation in basic mode showing results
7en | Bosch Security Systems Megapixel IP Cameras
F.01U.032.595 | V 1.0 | 2007.03 Quick Install Guide Bosch Security Systems
Fig. 1.2 Camera installation in advanced mode showing results
Advanced mode
1. Start making a list of Ethernet (MAC) addresses and IP
addresses assigned to them. The Ethernet address is on
the camera label.
2. Click Find Cameras.
3. Select a camera by clicking its Ethernet address.
4. Enter the IP address assigned to that camera in the New
Camera IP box.
5. Click Set IP.
6. Click Automatic.
7. Wait for result to change from unchecked to success.
8. Click Save / Exit when done.
Viewing the image
1. Open Internet Explorer.
2. In the address line, enter http://IPADDRESS/index.html.
3. Click Video to display the image.
4. Adjust the lens for optimal focus.
NOTICE! Adjust back focus if necessary.
a. Loosen the set screws in the top and bottom of the
front panel (use 1/16 inch hex key).
Megapixel IP Cameras Quick Install Guide | en 8
Bosch Security Systems Quick Install Guide F.01U.032.595 | V 1.0 | 2007.03
b. Rotate lens in or out with back focus ring until focus is
obtained.
c. Fasten the two set screws.
Ce manuel convient aux modèles suivants
2
Table des matières
Autres manuels Bosch Caméra de sécurité
Bosch
Bosch AutoDome VG5-825-ECEV Manuel utilisateur
Bosch
Bosch VEZ-400 Series Manuel utilisateur
Bosch
Bosch DINION IP starlight 7000 HD Manuel utilisateur
Bosch
Bosch VG4 Series Manuel utilisateur
Bosch
Bosch FlexiDome NDC-455V03-21PS Manuel utilisateur
Bosch
Bosch VBC?265 Series Manuel utilisateur
Bosch
Bosch Dinion2X NBN-498 Manuel utilisateur
Bosch
Bosch AUTODOME IP starlight 5000i Manuel utilisateur
Bosch
Bosch FlexiDomeXF VDC-485V03-20 Manuel utilisateur
Bosch
Bosch FLEXIDOME HD Instructions d'utilisation
Bosch
Bosch 200 Series Manuel utilisateur
Bosch
Bosch VDN-498V03-21S Manuel utilisateur
Bosch
Bosch FLEXIDOME IP micro 2000 Manuel utilisateur
Bosch
Bosch DINION IP 7000 HD NBN-71022 Manuel utilisateur
Bosch
Bosch VG5-7230-CPT5 Manuel utilisateur
Bosch
Bosch WZ14 Manuel utilisateur
Bosch
Bosch FlexiDomeXT+ VDC-455V03-20 Manuel utilisateur
Bosch
Bosch DINION XF LTC 0495 Manuel utilisateur
Bosch
Bosch NEI-Series Manuel utilisateur
Bosch
Bosch DINION IP starlight 7000 HD Manuel utilisateur
