Bosch AEC-AMC2-UL01 Manuel utilisateur
AMC2 enclosure with 1 DIN rail
AEC‑AMC2‑UL01
en Installation manual
AMC2 enclosure with 1
DIN rail Table of contents | en 3
Bosch Security Systems B.V. 2020-07 | V04 | F.01U.330.018
Table of contents
1System overview 4
1.1 Components of the enclosure 4
1.2 Parts included 6
1.3 Cables to be assembled 8
2Mounting the enclosure 10
3Connections 11
3.1 Connecting the devices 11
3.2 Connecting the cables 13
3.3 Connections for supporting Universal Power Supply 15
3.3.1 12 V mode operation 16
3.3.2 24 V mode operation 18
4Appendices 20
4.1 UL requirements 20
4.2 Cable assembly 21
4en | System overview AMC2 enclosure with 1
DIN rail
2020-07 | V04 | F.01U.330.018 Bosch Security Systems B.V.
1 System overview
1.1 Components of the enclosure
1 2 3 4
6
78
11
12
13
9
5
10
Figure1.1: Components of the enclosure
Position Description
1 Cover grounding point
2 Mounting rail for power supply unit (PSU) and
Access Modular Controller (AMC2)
3 AMC2 grounding point
4 Cable knock-outs for reader and signal cables
5 Temperature sensor bracket
6 Tamper contact
7 Fixing bracket for rechargeable batteries
8 Main grounding point
AMC2 enclosure with 1
DIN rail System overview | en 5
Bosch Security Systems B.V. 2020-07 | V04 | F.01U.330.018
Position Description
9 Label
10 Knock-out for the power cable connection
11 Three pin connector
12 Bracket for LED
13 Name plate
6en | System overview AMC2 enclosure with 1
DIN rail
2020-07 | V04 | F.01U.330.018 Bosch Security Systems B.V.
1.2 Parts included
x3 x1
x1
x1
x2A
B
E
C
D
x1
F
AMC2 enclosure with 1
DIN rail System overview | en 7
Bosch Security Systems B.V. 2020-07 | V04 | F.01U.330.018
Position Description
A Cable ties to secure cables
B Three screw anchors S8 and M6 × 50 screws
C Bracket for cable fixing
D Fuse and fuse holder
E LED
F Cover grounding cable
8en | System overview AMC2 enclosure with 1
DIN rail
2020-07 | V04 | F.01U.330.018 Bosch Security Systems B.V.
1.3 Cables to be assembled
D
A
C
B
E
F
Position Description
A Power supply cable (AMC2)
B Power supply cable (battery)
C Battery cable
D Cover contact wired
E Power cable
10 en | Mounting the enclosure AMC2 enclosure with 1
DIN rail
2020-07 | V04 | F.01U.330.018 Bosch Security Systems B.V.
2 Mounting the enclosure
The enclosure is designed to be mounted on a wall.
1. Open the door lock of the enclosure with the provided key.
2. Hold the enclosure at the desired position against the wall.
3. Mark the mounting holes on the wall with a pencil.
4. Put the enclosure aside.
5. Drill the holes at the points that you previously marked on
the wall.
6. Insert the screw anchors in the drilled holes.
7. Drive the screws halfway into the top and bottom left screw
anchors.
8. Hang the enclosure on the wall, according to the position of
the screw anchors.
9. Drive the third screw into the anchor on the bottom right.
10. Tighten all screws.
– The enclosure is installed.
86,5 mm
3,406 in
401 mm
15,787 in
352,5 mm
13,878 in
5 mm
0,197 in
318 mm
12,52 in
10 mm
0,394 in
5 mm
0,197 in
10 mm
0,394 in
200,5 mm
7,894 in
Figure2.1: Dimensions of the enclosure
Table des matières
Autres manuels Bosch Enceinte
Bosch
Bosch AMC2 VdS Manuel utilisateur
Bosch
Bosch CPH 0006 A Manuel utilisateur
Bosch
Bosch D8108A Manuel utilisateur
Bosch
Bosch AE20 Manuel utilisateur
Bosch
Bosch DSA E-Series (E2700) Manuel utilisateur
Bosch
Bosch FPA-5000 Manuel utilisateur
Bosch
Bosch AMC2 Series Manuel utilisateur
Bosch
Bosch HCP 0006 A Manuel utilisateur
Bosch
Bosch B8103 Manuel utilisateur
Bosch
Bosch D203 Instructions d'utilisation et d'entretien
