Bosch TouchOne Manuel utilisateur
TouchOne
Installaon Manual
2 3
Contents
“1. Overview” 4
“2. Wiring” 5
“3. Mounng” 6
“4. Addressing” 7
“5. Setup Wizard” 8
“6. Internet Connecvity” 7
“7. Troubleshoong” 10
“8. Specicaons” 11
4 5
1. Overview
The TouchOne is a High Denion, 7” Touchscreen Keypad for Bosch Soluon 2000 and
3000 control panels that provides a rich user interface and extended funconality to the
end user.
Generaon 2 builds on the powerful foundaon of the TouchOne with an all new Processor,
SmartColor display system, new touch panel and improved mounng design.
2. Wiring
Using the included Wire Harness, wire the TouchOne into the
control panel as per the wiring diagram. It is recommended to
solder the wires to the cable from the control panel.
Noce on Power Consumpon
The TouchOne consumes considerably more power than
a tradional codepad due to its HD screen and internet
connecvity. Only one TouchOne device can be powered
by the control panel to ensure reliable performance. Up to 4 TouchOne devices can
be connected to one system, however 3 of them must be powered by a seperate and
appropriately rated power supply.
Using a 0.5mm cable from the control panel with a run less than 15 meters is recommended
for best performance.
67
3. Mounng
The TouchOne can be mounted in two orientaons, either
portrait or landscape. The Wall Mount should be screwed onto
the wall rst using the included 6G x 20mm pan head screws in
the intended orientaon. In either orientaon, the circle screw
hole is always on the boom and the oval adjustment screw hole
should be on top. Plug the Wire Harness into the TouchOne.
Aligning the TouchOne to the Wall Mount’s hooks, it should
move closer to the wall when aligned correctly. Slide the TouchOne in the opposite
direcon of the camera unl you feel it clip. Ensure all wires are fed into the wall.
Removing
The TouchOne can be removed by pressing the clip
that is located on the back at the opposite side of the
camera. Using a nger or small screwdriver, push the clip
towards you and slide the TouchOne in the direcon of
the camera.
4. Addressing
The Bosch Soluon 2000 and 3000 control panel requires each codepad on the system to
have a unique address between 1 and 4. When the TouchOne is powered on for the rst
me, it defaults to address 1. This seng is changed in the TouchOne soware interface,
therefore, you must ensure that any other codepad on the system is either not addressed
to address 1 or disconnected unl you have completed the setup wizard and have changed
the TouchOne’s address.
Changing the address
You can change the TouchOne address on the soware interface aer the inital setup
wizard by touching the Sengs buon from the home screen and then the Change Address
buon.
Should the TouchOne detect there is another device on the bus that shares its address
or there are communicaon problems, a screen will automacally appear allowing you to
select another address.
8 9
5. Setup Wizard
When the TouchOne is powered on for the rst me, it will display a setup wizard, allowing
you to congure the device.
You can restore the TouchOne to factory defaults and complete the setup wizard again
by touching the Sengs buon from the home screen, then Installer Opons and then the
Restore to factory defaults buon. You will require the control panels installer PIN to access
the Installer Opons menu.
6. Internet Connecvity
During the setup wizard, you will be requested to connect the TouchOne to a local WiFi
network. As the TouchOne is a security device, ensure you only connect it to a WiFi network
that uses at least WPA security. WEP security is not a suitable encrypon method for this
device.
WiFi is required for the TouchOne to receive automac updates and to download and use
Apps like the Intercom App. The date and me must be correct before automac updates
and App funconality is enabled.
10 11
7. Troubleshoong
The TouchOne does not turn on. • Ensure the PWR LED on the back of the TouchOne is illuminated, indicang the
device is receiving power from the control panel.
• Ensure the TouchOne is wired correctly and there is a steady 11V to 13V on the
PWR and COM (Red and Black) wires (meter at the TouchOne side of the cable).
• Wire the TouchOne Wire Harness directly to the panel and test.
• Wire the TouchOne to another panel to test.
• Ensure there is not short between the PWR and COM wires.
The TouchOne does not start
completely / restarts oen.
• Remove power to the control panel, remove all other devices and just connect
the TouchOne. You may need to wait up to 5 minutes for the overload protecon
circuit to cool down. Apply power to the panel again.
• If the TouchOne does start correctly when performing this test, then the total
number of devices on the panel exceeds the maximum current draw and you may
need an external power supply.
• Reduce the screen brightness, disable WiFi and use the Sleep standby opon
instead of the photo slideshow.
The TouchOne shows a communicaon
failure message.
• Check the “ALIVE” LED on the back of the device to ensure communicaon is
stable (the LED should be ashing consistently).
• Ensure the wiring is correct.
• If the TouchOne is being powered by a separate power supply, the ground wire of
the power supply should also connect to the ground wire of the bus.
8. Specicaons
Dimensions 192.69 mm x 115.69 mm x 13.83 mm LCD 7” HD WXGA 1280 px x 800 px, IPS, 400
nits.
Maximum screw
size
6G pan head Touch Panel 5 point mul-touch, capacive, GF glass
touch sensor.
Voltage
(Operang)
12VDC SD Card MicroSD (SDHC) 2GB to 32GB
Current Normal: 400mA
Peak: 800mA
Compability ICP-SOL2 & ICP-SOL3
Firmware version 1.0.3+
8IM-TO2A-041601
Autres manuels pour TouchOne
1
Table des matières
Autres manuels Bosch Unité de contrôle
Bosch
Bosch MAP Control Center IUI-MAP0001-2 Manuel utilisateur
Bosch
Bosch B426 Manuel utilisateur
Bosch
Bosch 715ES Manuel de référence
Bosch
Bosch Control 8311 Manuel utilisateur
Bosch
Bosch D113 Manuel utilisateur
Bosch
Bosch Denoxtronic 2.1 Caractéristiques techniques
Bosch
Bosch FLM-420-RLV1-E Manuel utilisateur
Bosch
Bosch Rexroth DB 5X XC Series Manuel utilisateur
Bosch
Bosch FLM-420/4-CON-S Manuel utilisateur
Bosch
Bosch B901 Manuel utilisateur
Bosch
Bosch rexroth SB11 Manuel utilisateur
Bosch
Bosch SE352 Manuel utilisateur
Bosch
Bosch KTS 5a Series Manuel utilisateur
Bosch
Bosch Conettix C900V2 Manuel utilisateur
Bosch
Bosch CL400 Manuel utilisateur
Bosch
Bosch Rexroth SM 12 Mode d'emploi
Bosch
Bosch Rexroth ctrlX I/O XI322204 Manuel utilisateur
Bosch
Bosch B520 Instructions d'utilisation et d'entretien
Bosch
Bosch B426 Manuel utilisateur
Bosch
Bosch VCU MS 50.4P Manuel utilisateur
Manuels Unité de contrôle populaires d'autres marques
Festo
Festo Compact Performance CP-FB6-E Manuel de la liste des pièces
Elo TouchSystems
Elo TouchSystems DMS-SA19P-EXTME Manuel utilisateur
JS Automation
JS Automation MPC3034A Manuel utilisateur
JAUDT
JAUDT SW GII 6406 Series Guide rapide
Spektrum
Spektrum Air Module System Manuel utilisateur
BOC Edwards
BOC Edwards Q Series Manuel utilisateur
