Page 5
BN Products-USA, LLC.
3450 Sabin Brown Road • Wickenburg, AZ 85390
(800) 992-3833 • (928) 684-2813 • mail@bnproducts.com
CAUTION- Hydraulic oil is highly ammable. Keep
away from sparks and naked ame. DO NOT SMOKE
WHEN NEAR OIL/BENDER.
CAUTION- Hydraulic oil may cause inammation of
the eyes and skin. If ingested, it will cause diarrhea and
vomiting.
In case of eye contact, rinse in clean water for at least 15
minutes and consult a physician immediately, as blind-
ness can occur.
In case of skin contact, wash thoroughly with soap and
water.
In case of ingestion, consult a physician immediately.
DO NOT DELIBERATELY INDUCE VOMITING.
OIL MAINTENANCE CON’T.
1. Oil should be warm, but not hot. Warm up the unit
if cold.
2. Unplug unit from the power source.
3. Remove oil plug and the seal washer (packing)
4. CAUTION- Never remove oil plug when unit is hot,
as the oil may spurt over.
5. Check that oil is level with the bottom of the plug
hole (i.e. the pump case is full to the brim) If oil level
is too low, top up with 20- weight hydraulic oil with
anti-foam and anti- abrasion properties (ISO viscos-
ity grade VG46, e.g., Shell Tellus 46, Mobil Oil DTE-
25, or Esso Uni Power SQ46)
6. After topping up, extract air from the system. Gently
tilt the unit and return it to the level position. Top
up again and tilt in the opposite direction. Repeat
this action until all air has been removed.
7. CARE- Rebar straightener cannot function properly
if oil contains air bubbles.
8. Replace seal washer and plug. Extend to its full
stroke, and remove oil plug and seal washer. Then
repeat the procedure of above
9. Replace the oil plug and seal washer.
OIL CHANGE
The hydraulic oil should be changed at least once a year,
sooner if it appears to be dirty.
1. Unplug the unit from the power source. Remove the
oil plug and packing. Turn the unit over and drain
oil into an appropriate receptacle.
2. With drain hole uppermost, slowly ll the unit with
fresh oil. Replace plug and lightly tighten. Connect
the unit to power source and advance piston two
or three times. Unplug the unit and remove the oil
plug. Top up the oil level and replace plug.
3. Finally, follow procedure for oil level check.
Please dispose of any hydraulic oil in accordance with
local regulations. Do not pour into sea, a river, lake or
drains.
BOLT TIGHTNESS
Once a week, or after every 30 times use, check the tight-
ness of all bolts, especially those securing the housing to
the cylinder.
CARBON BRUSHES
Inspect the two carbon brushes at least every two
months. (Normal brush life is around 200 hours.
CARE- Warn carbon brushes will result in power loss,
cause the motor to run hot and irreparably damaging
the armature’s commutator.
1. Disconnect unit.
2. Unscrew both brush caps and pull out the carbon
brushes.
3. Replace the brushes if less than 6MM in length.
OVERHAUL
Return the unit to an authorized agent for overhaul at
least once every two years, sooner if subject to heavy us-
age.
BN Products-USA, LLC.
3450 Sabin Brown Road • Wickenburg, AZ 85390
(800) 992-3833 • (928) 684-2813
Fax: (928) 684-7041• mail@bnproducts.com
WWW.bnrebartools.com
Maximum Bending Diameter 1” #8 Rebar (25mm) Grade 60
Bending Angle Up to 94 degrees (1/2”) - up to
90 degrees ( 1”)
Voltage/ Amperage 115V 50/60Hz / 12 amps
Tool Weight 57.3 lbs (26 kg)
Dimensions L x W x H 25.75” (660mm) x 10.5”
(270mm) x 7.8” (200mm)
