Black Box LB9020A Manuel utilisateur

Installation

This installation guide gives step-by-step instructions about how to install the Express Plus Ethernet Switches:

LB9020A

Selecting a Site for the Express Plus Ethernet Switch: LB9020A

As with any electric device, you should place the switch where it will not be subjected to extreme temperatures, humidity,

or electromagnetic interference. Specifically, the site you select should meet the following requirements:

-The ambient temperature should be between 32 and 104 degrees Fahrenheit (0 to 40 degrees Celsius).

-The relative humidity should be less than 90 percent, non-condensing.

-Surrounding electrical devices should not exceed the electromagnetic field (RFC) standards for IEC

801-3, Level 2 (3V/M) field strength.

-Make sure that the switch receives adequate ventilation. Do not block the ventilation holes on each side of

the switch or the fan exhaust port on the rear of the switch.

-The power outlet should be within 1.8 meters of the switch.

Connecting to Power

Internal power:

Step 1:Connect the supplied AC power cord to the receptacle on the back of the switch, and then plug it into a standard AC outlet with a

voltage range from 100 to 260 Vac.

Step 2:Turn on the switch by flipping the ON/OFF switch on the rear of the unit to I (ON) position.

Step 3:The Oposition is OFF.

Figure 1: Rear view

CUSTOMER

SUPPORT

INFORMATION

Order toll

free in the U.S. 24 hours, 7 A.M. Monday to midnight Friday

: 877

877

BBOX

FREE technical support, 24 hours a day, 7 days a week: Call 724-746-5500 or fax 724-

746-0746

Mail order: Black Box Corporation, 1000 Park Drive, Lawrence, PA 15055-1018

Web site:

www.blackbox.com • E-mail: [email protected]

Connecting to Your Network

Cable Type & Length

It is necessary to follow the cable specifications below when connecting the switch to your network. Use

appropriate cables that meet your speed and cabling requirements.

Table 3: Cable Specifications

Speed Connector Port

Speed

Half/Full

Duplex

Cable Max.

Distance

10BASE-TRJ-45 10/20

Mbps 2-pair UTP/STP

Cat. 3, 4, 5 100 m

100BASE-TX RJ-45 100/200

Mbps 2-pair UTP/STP

Cat. 5 100 m

100BASE-FX ST, SC, MT-RJ,

VF-45 100/200

Mbps MMF (50 or

62.5µm) 2 km

100BASE-FX SC 100/200

Mbps SMF (9 or

10µm) 15, 40, or

75 km

Cabling

Step 1: First, ensure the power of the switch and end devices is turned off.

<Note> Always ensure that the power is off before any installation.

Step 2: Prepare cable with corresponding connectors for each type of port in use.

<Note> To connect two regular RJ-45 ports between switches or hubs, you need a cross-over cable.

Step 3:Consult Cable Specifications Table on previous page for cabling requirements based on connectors and speed.

Step 4:Connect one end of the cable to the switch and the other end to a desired device.

Step 5:Once the connections between two end devices are made successfully, turn on the power and the switch is operational.

CUSTOMER

SUPPORT

INFORMATION

Order toll

free in the U.S. 24 hours, 7 A.M. Monday to midnight Friday

: 877

877

BBOX

FREE technical support, 24 hours a day, 7 days a week: Call 724-746-5500 or fax 724-

746-0746

Mail order: Black Box Corporation, 1000 Park Drive, Lawrence, PA 15055-1018

Web site:

www.blackbox.com • E-mail: [email protected]

Table des matières

Autres manuels Black Box Changer

Black Box

Black Box ServSwitch Secure Plus (with USB) Manuel utilisateur

Black Box

Black Box SW1033A Manuel utilisateur

Black Box

Black Box LGT616A-JP Manuel utilisateur

Black Box

Black Box LH8050A Manuel utilisateur

Black Box

Black Box 26592 Manuel utilisateur

Black Box

Black Box LBH100A-PD-ST-24 Manuel utilisateur

Black Box

Black Box Hub Manuel utilisateur

Black Box

Black Box PI750A Manuel utilisateur

Black Box

Black Box LB8405A-R2 Manuel utilisateur

Black Box

Black Box SW459A-ST Manuel utilisateur

Black Box

Black Box EMS1G-48 Manuel utilisateur

Black Box

Black Box KV5016FA-R2 Manuel utilisateur

Black Box

Black Box ServSwitch KV0004A Manuel utilisateur

Black Box

Black Box USB Single-Port Hub IC266A Manuel utilisateur

Black Box

Black Box SWI080A-R3 Manuel utilisateur

Black Box

Black Box LPH008A-R2 Manuel utilisateur

Black Box

Black Box ServSwitch DTX5000 Manuel utilisateur

Black Box

Black Box Express Entry LB9005A-FO-R2 Manuel utilisateur

Black Box

Black Box AVSW-VGA8X8-B Manuel utilisateur

Black Box

Black Box SS2P-SH-HDMI-U Manuel utilisateur

Black Box

Black Box LB9032A Manuel utilisateur

Black Box

Black Box ServSwitch CX Quad IP KV4161A Manuel utilisateur

Black Box

Black Box LE2700A Manuel utilisateur

Black Box

Black Box ACU7017A Manuel utilisateur

Manuels Changer populaires d'autres marques

URC

URC Total Control MFS-8 Manuel utilisateur

Azbil

Azbil HPQ-D11 Manuel utilisateur

Sony

Sony DFS-900M Manuel utilisateur

SICK

SICK i17S Manuel utilisateur

F&F

F&F SZR-277 Manuel utilisateur

Shure

Shure UAMS/BK Manuel utilisateur

Dräger

Dräger X-zone Switch Off Manuel utilisateur

Asco

Asco Joucomatic 349 Series Manuel utilisateur

BT Mini Hub Manuel utilisateur

D-Link

D-Link DES-1226G Manuel utilisateur

Johnson Controls

Johnson Controls FS80-C Manuel utilisateur

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Manuel utilisateur

MicroNet

MicroNet SP1200A Manuel utilisateur

Ruijie

Ruijie RG-PF2920 Series Manuel d'installation et d'exploitation

Altinex

Altinex DA1914SX Manuel utilisateur

MiLAN

MiLAN MIL-SM2401M Manuel utilisateur

RJM

RJM MASTERMIND PBC/6X Manuel utilisateur

Atlas

Atlas MMK-KVM8 Manuel utilisateur