Black Box ACU8000A Manuel utilisateur

ACU8000A

UMA1178 Rev NC

ServSwitch Universal Extender

Extend dual-head VGA video, stereo audio, RS-232

and up to three independent USB ports up to 400

feet (125 m) away on CATx cable.

724-746-5500 | blackbox.com 1

ServSwitch Universal Extender

TRADEMARKS USED IN THIS MANUAL

BLACK BOX and its Double Diamond logo are registered trademarks, and ServSwitch is a

trademark of BB Technologies, Inc.

Any other trademarks mentioned in this manual are acknowledged to be the property of the

trademark owners.

We‘re here to help!

If you have any questions about your application or our

products, contact Black Box Tech Support at 724-746-5500

or go to blackbox.com and click on “Talk to Black Box.”

You’ll be live with one of our technical experts in less

than 20 seconds.

724-746-5500 | blackbox.com

ServSwitch Universal Extender

FEDERAL COMMUNICATIONS COMMISSION AND INDUSTRY CANADA

RADIO FREQUENCY INTERFERENCE STATEMENTS

This equipment generates, uses, and can radiate radio-frequency energy, and if not installed and used properly, that

is, in strict accordance with the manufacturer’s instructions, may cause interference to radio communication. It has

been tested and found to comply with the limits for a Class A computing device in accordance with the specifications

in Subpart J of Part 15 of FCC rules, which are designed to provide reasonable protection against such interference

when the equipment is operated in a commercial environment. Operation of this equipment in a residential area is

likely to cause interference, in which case the user; at own expense; will be required to take whatever measures may

be necessary to correct the interference.

Changes or modifications not expressly approved by the party responsible for compliance could void the user’s

authority to operate the equipment. This digital apparatus does not exceed the Class A limits for radio noise emission

from digital apparatus set out in the Radio Interference Regulation of Industry Canada

Le présent appareil numérique n’émet pas de bruits radioélectriques dépassant les limites applicables aux appareils

numériques de classe A prescrites dans le Règlement sur le brouillage radioélectrique publié par Industrie Canada.

724-746-5500 | blackbox.com 3

ServSwitch Universal Extender

INSTRUCCIONES DE SEGURIDAD

Normas Oficiales Mexicanas (NOM) Electrical Safety Statement

1. Todas las instrucciones de seguridad y operación deberán ser leídas antes de que el aparato eléctrico

sea operado.

2. Las instrucciones de seguridad y operación deberán ser guardadas para referencia futura.

3. Todas las advertencias en el aparato eléctrico y en sus instrucciones de operación deben ser

respetadas.

4. Todas las instrucciones de operación y uso deben ser seguidas.

5. El aparato eléctrico no deberá ser usado cerca del agua—por ejemplo, cerca de la tina de baño, lavabo,

sótano mojado o cerca de una alberca, etc.

6. El aparato eléctrico debe ser usado únicamente con carritos o pedestales que sean recomendados por

el fabricante.

7. El aparato eléctrico debe ser montado a la pared o al techo sólo como sea recomendado por el

fabricante.

8. Servicio—El usuario no debe intentar dar servicio al equipo eléctrico más allá a lo descrito en las

instrucciones de operación. Todo otro servicio deberá ser referido a personal de servicio calificado.

9. El aparato eléctrico debe ser situado de tal manera que su posición no interfiera su uso. La colocación

del aparato eléctrico sobre una cama, sofá, alfombra o superficie similar puede bloquea la ventilación, no

se debe colocar en libreros o gabinetes que impidan el flujo de aire por los orificios de ventilación.

10. El equipo eléctrico deber ser situado fuera del alcance de fuentes de calor como radiadores, registros de

calor, estufas u otros aparatos (incluyendo amplificadores) que producen calor.

11. El aparato eléctrico deberá ser connectado a una fuente de poder sólo del tipo descrito en el instructivo

de operación, o como se indique en el aparato.

12. Precaución debe ser tomada de tal manera que la tierra fisica y la polarización del equipo no sea

eliminada.

13. Los cables de la fuente de poder deben ser guiados de tal manera que no sean pisados ni pellizcados

por objetos colocados sobre o contra ellos, poniendo particular atención a los contactos y receptáculos

donde salen del aparato.

14. El equipo eléctrico debe ser limpiado únicamente de acuerdo a las recomendaciones del fabricante.

15. En caso de existir, una antena externa deberá ser localizada lejos de las lineas de energia.

16. El cable de corriente deberá ser desconectado del cuando el equipo no sea usado por un largo periodo

de tiempo.

17. Cuidado debe ser tomado de tal manera que objectos liquidos no sean derramados sobre la cubierta u

orificios de ventilación.

18. Servicio por personal calificado deberá ser provisto cuando:

a. El cable de poder o el contacto ha sido dañado; u

b. Objectos han caído o líquido ha sido derramado dentro del aparato; o

c. El aparato ha sido expuesto a la lluvia; o

d. El aparato parece no operar normalmente o muestra un cambio en su desempeño; o

e. El aparato ha sido tirado o su cubierta ha sido dañada.

724-746-5500 | blackbox.com

ServSwitch Universal Extender

Contents

1. SPECIFICATIONS ................................................................................................................5

2. OVERVIEW ...........................................................................................................................6

2.1 INTRODUCTION...........................................................................................................6

2.2 FEATURES .................................................................................................................6

2.3 WHAT’S INCLUDED...................................................................................................... 6

2.4 HARDWARE DESCRIPTION........................................................................................... 7

3. INSTALLATION ..................................................................................................................13

3.1 CONNECTING THE SENDER UNIT TO THE PC ..............................................................13

3.2 CONNECTING THE SENDER UNIT TO LOCAL OUTPUTS................................................. 14

3.3 CONNECTING THE SENDER UNIT TO THE RECEIVER UNIT............................................14

3.4 CONNECTING THE RECEIVER UNIT OUTPUTS .............................................................15

4. CONFIGURATION & OPERATION....................................................................................16

4.1 SENDER UNIT FRONT-PANEL CONTROLS AND INDICATORS .........................................16

4.2 RECEIVER UNIT FRONT-PANEL CONTROLS AND INDICATORS ......................................17

4.3 VIDEO CALIBRATION .................................................................................................18

4.4 AUDIO ADJUSTMENT.................................................................................................20

4.5 RECEIVER COVER ....................................................................................................20

6. TROUBLESHOOTING........................................................................................................21

6.1 CALLING BLACK BOX ................................................................................................22

6.3 SHIPPING AND PACKAGING........................................................................................22

APPENDIX .............................................................................................................................22

724-746-5500 | blackbox.com 5

ServSwitch Universal Extender

1. Specifications

Cable Required Up to 400 feet using CAT5e UTP cable;

Up to 450 feet using CAT6 UTP cable

Enclosure Steel

MTBF 90,000 hours (calculated estimate)

Resolutions PC resolutions up to 1920 x 1200 @ 60 Hz

USB Support High-Speed (12 Mbps) devices,

Low-Speed (1.5 Mbps) devices

Video Inputs PC outputs (VGA to UXGA)

Video Levels 0 to 0.7 v p-p

Temperature Tolerance Operating: +32 to +122 degF (0 to +50 degC);

Storage: -40 to +185 degF (-40 to + 85 degC)

Power 100-240 VAC, 50/60 Hz

Size

Sender: 1.5” H x 19” W x 5.1” D (3.8 x 48.2 x 12.9 cm);

Receiver 1.75” H x 14” W x 4.1” D (4.5 x 35.6 x 10.4 cm)

Weight

Sender 4 lb. (1.8 kg);

Receiver 4 lb. (1.8 kg)

724-746-5500 | blackbox.com

ServSwitch Universal Extender

2. Overview

2.1 Introduction

The ServSwitch Universal Extender (ACU8000A) extends dual-head PC video, stereo audio

(amplified or line level), RS-232, and up to three USB ports up to 400 feet away on CAT5e or

CAT6 cables. The ACU8000A includes a rack mountable sender unit plus a wall mountable

receiver (and I/O hood cover), packaged together. The Receiver (Remote) Unit is a peripheral

extender with two direct USB ports (DR1 and DR2). The Sender (Local) Unit is a peripheral

extender with two direct USB ports (DR1 and DR2).

A block diagram of the system is shown in Appendix A

2.2 Features

•Eliminates the need for a utility box (The receiver includes an I/O hood cover that goes over all the connectors

with tie-down provisions for a strain relief.)

•Does not require external power supply. It has a built-in supply with a standard 110~240 VAC IEC320 jack.

•2 “Direct” USB ports (DR1 and DR2)

•Has a DB15 connector for audio input and loop output at the sender as well as a DB15 output at the receiver.

The units are perfect for PCs that have amplified audio output on a DB15 male connector (no special cables

are needed other than the included DB15 M/F cable)

•Receiver features a DB15 male output with amplified output to drive passive speakers directly, as well as a

line-level 3.5-mm jack for powered speakers

•Provides built-in video skew correction on both video channels. This corrects the lack of RGB convergence

when long Cat6 cables are used. Eliminates the need to use special low-skew UTP cables for long runs.

•Built-in Test pattern generator for long cable compensation (High Frequency Gain) and Skew correction.

•Features a built-in extended display ID (EDID), which enables the PC to detect LCD’s even if none is

connected at the sender or the receiver.

•Supports Local USB outputs at the sender to connect the local keyboard and mouse.

•Offers 4 general-purpose USB ports at the remote unit plus two direct USB ports

•Supports hot-unplug and hot-plug of USB Peripherals (General Purpose USB ports, as well as DR1 and DR2)

2.3 What’s included

Your ACU8000A package should contain the following items. If anything is missing or

damaged, contact Black Box Technical Support at 724-746-5500 or [email protected].

•(1) Rack Mountable Sender Unit

•(1) Wall Mountable Receiver Unit

•(1) I/O hood cover with mounting hardware

•(3) 6-ft. (1.8m) USB Type A male to Type B male cables

•(2) 6-ft. (1.8m) VGA cables

•(2) 6-ft. (1.8 m) power cable

•(1) DB15 to 3.5-mm connector male/male cable

•This user’s manual

724-746-5500 | blackbox.com 7

ServSwitch Universal Extender

2.4 Hardware Description

2.4.1 Sender Unit

Figure 2.1 shows the sender unit’s front panel. Table 2-1 describes its components.

TABLE 2-1

Number Component Description

1 Host and Link LED’s

(STD, DR1, DR2)

Illuminated when communication is established

between sender and host or sender and receiver

2 Power LED Lights when sender is powered on

3 Video Adjust Switch Selects normal “RUN” mode or “CAL” mode for display

of the video test pattern

TABLE 2-2

Number Component Description

4 HD15 connector

VGA A IN: Along with VGA B IN, these are the PC’s

video input signals (VGA through UXGA) with local loop

outputs at the sender. They are extended to a remote

unit through RJ-45 Port A and Port B. High-frequency

compensation is incorporated at the receiver to provide

a brilliant image for these video signals.

5 HD15 connector

VGA B IN: Along with VGA A IN, these are the PC’s

video input signals (VGA through UXGA) with local loop

outputs at the sender. They are extended to a remote

unit through RJ-45 Port A and Port B. High-frequency

compensation is incorporated at the receiver to provide

a brilliant image for these video signals.

Figure 2.1 Sender unit’s front panel

Figure 2.2 Sender unit’s back panel

4 9

10 11

12 13 14 20

17 19

16 18

724-746-5500 | blackbox.com

ServSwitch Universal Extender

TABLE 2-2

Number Component Description

6 DB15 connector

Audio input: Audio: DB15 connector (with 2 rows of

pins) for audio input and a loop output at the sender.

The audio is extended to a remote receiver that has

both line as well as powered outputs (for driving

passive speakers). The DB15 audio I/O not only allows

Interface with line-level 3.5-mm mini stereo audio

sources (using adapter cable available from Black Box),

it also provides a more reliable and secure means for

the audio connection with its gold-plated D-Sub

connector with jack screws. The audio input level

supports a wide range of standards; it can be amplified

(for driving passive speakers), +4dBu (Pro-Audio), or -

10dBv (consumer line-level).

7 DB9 connector RS-232 input

8 USB Type B connector

DR 1 input: Along with DR2, these are two “Direct”

extension USB ports. The corresponding USB port on

the PC is directly extended to a remote receiver with no

hubs or other functions in the path. The PC’s USB port

that is extended via DR1 or DR2 behaves exactly as if it

were connected directly to the target device at the

remote. These “Direct” USB port extensions are perfect

for high-data-rate devices, such as video cameras,

storage media, printers, and chart recorders. They do

not support low-speed “human interface” devices, such

as keyboards or mice. Having a dedicated path from

the target device to the PC ensures full channel

bandwidth availability in the interface (as opposed to

several devices sharing one port on the PC via a hub).

9 USB Type B connector

USB STD input: This is a general-purpose USB port,

which goes through a hub in the sender and provides

two USB local output ports. It is also extended to the

remote receiver, where another hub provides the user

with four USB ports. These general-purpose USB ports

are labeled as KBRD 1, MOUSE 2, AUX 3, and AUX 4.

They support any type of low-speed or high-speed USB

devices. AUX 3 and AUX 4 are typically used for touch

screen displays, but support all other USB devices as

well.

10 USB Type A connector USB Local 1 output

11 USB Type A connector USB Local 2 output

12 HD15 connector Local VGA A output

13 HD15 connector Local VGA B output

724-746-5500 | blackbox.com 9

ServSwitch Universal Extender

TABLE 2-2

Number Component Description

14 DB15 connector Audio output

15 USB Type B

DR 2 input: This is a “Direct” extension USB port. The

corresponding USB port on the PC is directly extended

to a remote receiver with no hubs or other functions in

the path. The PC’s USB port that is extended via DR1

or DR2 behaves exactly as if it were connected directly

to the target device at the remote. These “Direct” USB

port extensions are perfect for high-data-rate devices,

such as video cameras, storage media, printers, and

chart recorders. They do not support low-speed “human

interface” devices, such as keyboards or mice. Having

a dedicated path from the target device to the PC

ensures full channel bandwidth availability in the

interface (as opposed to several devices sharing one

port on the PC via a hub).

16 RJ-45 connector Port D: DR2. Omit if DR2 not required

17 RJ-45 connector Port C: General purpose USB and DR1 USB. Required

in all applications

18 RJ-45 connector Port B: Video B, RS-232: May omit if Video B or RS-

232 extension is not needed.

19 RJ-45 connector Port A: Video A, Audio, Calibration Switch State:

Required in all applications

20 3-prong connector Power 100-240 VAC, 50/60 Hz

Table des matières

Autres manuels Black Box Extenseur

Black Box

Black Box IC540A Manuel utilisateur

Black Box

Black Box ServSwitch ACX310F Manuel utilisateur

Black Box

Black Box AC550A Manuel utilisateur

Black Box

Black Box AC163A Manuel utilisateur

Black Box

Black Box ACU5050A Manuel utilisateur

Black Box

Black Box LR0025A-KIT Manuel utilisateur

Black Box

Black Box ServSwitch ACU5200A Manuel utilisateur

Black Box

Black Box ServSwitch ACU2500A Manuel utilisateur

Black Box

Black Box IC247A Manuel utilisateur

Black Box

Black Box Wizard AVU5001A Manuel utilisateur

Black Box

Black Box LB200A Manuel utilisateur

Black Box

Black Box VX-HDB2-KIT Manuel utilisateur

Black Box

Black Box ServSwitch KV1400A Manuel utilisateur

Black Box

Black Box ServSwitch ACS235A Manuel utilisateur

Black Box

Black Box ServSwitch ACU5114A Manuel utilisateur

Black Box

Black Box AC555A Manuel utilisateur

Black Box

Black Box ServSwitch ACU5010A Manuel utilisateur

Black Box

Black Box IC406A Manuel utilisateur

Black Box

Black Box Wizard AVU5001A Manuel utilisateur

Black Box

Black Box LBPS310A-KIT Manuel utilisateur

Black Box

Black Box ACS1009A series Manuel utilisateur

Black Box

Black Box EHN250-0050 Manuel utilisateur

Black Box

Black Box LB532A-M Manuel utilisateur

Black Box

Black Box ACU1600A Manuel utilisateur

Manuels Extenseur populaires d'autres marques

SY HDBT-60T Manuel utilisateur

Appsys ProAudio

Appsys ProAudio ADX-16 Manuel utilisateur

Atlona

Atlona RS232 Manuel utilisateur

IDK

IDK OPF-TH1000-A Manuel utilisateur

Enable-IT

Enable-IT 824WP Manuel utilisateur

Worx

Worx Landroid RadioLink WA0864 Fiche technique

TP-Link

TP-Link TL-WA730RE Manuel utilisateur

Camplex

Camplex CMX-HDMI-SFPL Manuel utilisateur

SC&T

SC&T HE03-4K Manuel utilisateur

Marmitek

Marmitek MegaView70 Manuel utilisateur

Samsung

Samsung SCS-26UC4 Manuel utilisateur

Foxun

Foxun SX-GES24 Manuel utilisateur

MuxLab

MuxLab 500771 Manuel utilisateur

foxunhd

foxunhd SX-AEX01 Manuel utilisateur

TERK Technologies

TERK Technologies LFIRX2 Manuel utilisateur

Devolo

Devolo Audio Extender Manuel

Edimax

Edimax EW-7438RPn V2 Manuel utilisateur

Shinybow USA

Shinybow USA SB-6335T5 Manuel utilisateur