Black Box IC610A Manuel utilisateur
SEPTEMBER 1999
IC610A
IC612A
V.35 Rate Adapter/64
X.21 Rate Adapter/64
CUSTOMER SUPPORT INFORMATION
Order toll-free in the U.S.: Call 877-877-BBOX (outside U.S. call 724-746-5500)
FREE technical support 24 hours a day, 7 days a week: Call 724-746-5500 or fax 724-746-0746
Mailing address: Black Box Corporation, 1000 Park Drive, Lawrence, PA 15055-1018
RATE
ADAPTER/64
1
FCC AND IC STATEMENTS
FEDERAL COMMUNICATIONS COMMISSION
AND
INDUSTRY CANADA
RADIO FREQUENCY INTERFERENCE STATEMENTS
This equipment generates, uses, and can radiate radio frequency energy
and if not installed and used properly, that is, in strict accordance with the
manufacturer’s instructions, may cause interference to radio communication.
It has been tested and found to comply with the limits for a Class A computing
device in accordance with the specifications in Subpart B of Part 15 of FCC rules,
which are designed to provide reasonable protection against such interference
when the equipment is operated in a commercial environment. Operation of
this equipment in a residential area is likely to cause interference, in which case
the user at his own expense will be required to take whatever measures may be
necessary to correct the interference.
Changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
This digital apparatus does not exceed the Class A limits for radio noise emission from
digital apparatus set out in the Radio Interference Regulation of Industry Canada.
Le présent appareil numérique n’émet pas de bruits radioélectriques dépassant les limites
applicables aux appareils numériques de classe A prescrites dans le Règlement sur le
brouillage radioélectrique publié par Industrie Canada.
TRADEMARKS USED IN THIS MANUAL
Any trademarks mentioned in this manual are acknowledged
to be the property of the trademark owners.
2
RATE ADAPTER/64
NORMAS OFICIALES MEXICANAS (NOM)
ELECTRICAL SAFETY STATEMENT
INSTRUCCIONES DE SEGURIDAD
1. Todas las instrucciones de seguridad y operación deberán ser leídas antes
de que el aparato eléctrico sea operado.
2. Las instrucciones de seguridad y operación deberán ser guardadas para
referencia futura.
3. Todas las advertencias en el aparato eléctrico y en sus instrucciones de
operación deben ser respetadas.
4. Todas las instrucciones de operación y uso deben ser seguidas.
5. El aparato eléctrico no deberá ser usado cerca del agua—por ejemplo,
cerca de la tina de baño, lavabo, sótano mojado o cerca de una alberca,
etc..
6. El aparato eléctrico debe ser usado únicamente con carritos o pedestales
que sean recomendados por el fabricante.
7. El aparato eléctrico debe ser montado a la pared o al techo sólo como sea
recomendado por el fabricante.
8. Servicio—El usuario no debe intentar dar servicio al equipo eléctrico más
allá a lo descrito en las instrucciones de operación. Todo otro servicio
deberá ser referido a personal de servicio calificado.
9. El aparato eléctrico debe ser situado de tal manera que su posición no
interfiera su uso. La colocación del aparato eléctrico sobre una cama,
sofá, alfombra o superficie similar puede bloquea la ventilación, no se
debe colocar en libreros o gabinetes que impidan el flujo de aire por los
orificios de ventilación.
3
NOM STATEMENTS
10. El equipo eléctrico deber ser situado fuera del alcance de fuentes de calor
como radiadores, registros de calor, estufas u otros aparatos (incluyendo
amplificadores) que producen calor.
11. El aparato eléctrico deberá ser connectado a una fuente de poder sólo del
tipo descrito en el instructivo de operación, o como se indique en el
aparato.
12. Precaución debe ser tomada de tal manera que la tierra fisica y la
polarización del equipo no sea eliminada.
13. Los cables de la fuente de poder deben ser guiados de tal manera que no
sean pisados ni pellizcados por objetos colocados sobre o contra ellos,
poniendo particular atención a los contactos y receptáculos donde salen
del aparato.
14. El equipo eléctrico debe ser limpiado únicamente de acuerdo a las
recomendaciones del fabricante.
15. En caso de existir, una antena externa deberá ser localizada lejos de las
lineas de energia.
16. El cable de corriente deberá ser desconectado del cuando el equipo no
sea usado por un largo periodo de tiempo.
17. Cuidado debe ser tomado de tal manera que objectos liquidos no sean
derramados sobre la cubierta u orificios de ventilación.
18. Servicio por personal calificado deberá ser provisto cuando:
A: El cable de poder o el contacto ha sido dañado; u
B: Objectos han caído o líquido ha sido derramado dentro del
aparato; o
C: El aparato ha sido expuesto a la lluvia; o
D: El aparato parece no operar normalmente o muestra un cambio en
su desempeño; o
E: El aparato ha sido tirado o su cubierta ha sido dañada.
1. Specifications
Speed – DTE side: 1200, 2400, 4800, 7200, 9600,
14,400, 19,200 bps; DCE (ISDN) side: 64 kbps
(in compliance with Bearer [B] Channel
specifications of ISDN)
Operation – Asynchronous or synchronous;
full duplex
Character length – Selectable: 8, 9, 10, 11 bits
in asynchronous mode
Control signals – RTS, DTR, CD, DSR, CTS passed
through according to CCITT I.463 (V.110)
Interface – Terminal side: EIA 232-C/CCITT
V.24; DCE side: CCITT V.35 (IC610A model)
or X.21 (IC612A model)
Connectors – Terminal side: DB25 female;
DCE side: DB15 female (IC612A) or
34-pin M block female (IC610A)
Indicators – Power: green LED; Sync loss: red LED
(lights up at loss of synchronization)
Temperature – 32 to 122°F (0 to 50°C);
Humidity – Up to 95% noncondensing
Power – 115 VAC, 7.5 V at 300 mA, supplied by
120 V wallmount adapter; PS321E: 230 VAC,
50 Hz
Size – 1.2"H x 2"W x 5.3"D (3 x 5.1 x 13.5 cm)
Weight – 0.2 lb. (0.1 kg)
4
RATE ADAPTER/64
5
CHAPTER 2: Introduction
2. Introduction
2.1 Features of the Rate Adapter/64
• Connects EIA 232/V.24 DTEs to the
B-channel (64 kbps) of an ISDN connection
• Can be used as a rate adapter in non-ISDN
applications
• Converts EIA-232 data rates of 1200–19,200 bps
• Handles asynchronous or synchronous data
• Compatible with CCITT I.463 or I.460 (V.110)
recommendations
• Compatible with CCITT V.35 or X.21
2.2 Description
The Rate Adapter/64 lets your EIA 232-compliant
DTEs running at up to 19.2 kbps exchange data
over 64-kbps channels on an ISDN circuit.
The Rate Adapter/64 converts the DTE speed (up to
19.2 kbps) of your PCs, terminals, etc., to the Bearer
(B) channel 64-kbps rate associated with high-speed
digital transmission service (ISDN, unformatted
DDS). Thus you can use the same data equipment
you were using with analog data service when you tap
into a high-speed digital line.
With the Rate Adapter/64, you can exchange
asynchronous or synchronous data in full-duplex
operation. The control signals RTS, DTR, CD, DSR,
and CTS are passed through end-to-end, in
compliance with CCITT I.463 (V.110) and I.460
recommendations. Two LEDs indicate when the unit
is powered on and when there is a loss of signal
synchronization.
The Rate Adapter/64 is not limited to the ISDN
environment. It can be used in any application that
requires conversion from EIA 232/V.24 low-speed
data rates (up to 19.2 kbps) to a V.35 or X.21
high-speed (64-kbps) channel.
The lightweight and compact Rate Adapter/64
is easy to install; average installation time is about
10 minutes. Power is supplied by an external
wall-mount power supply for 120 VAC. A 230-VAC,
50-Hz power supply is also available (our part
number PS321E).
6
RATE ADAPTER/64
7
CHAPTER 3: Installation
3. Installation
1. Open the unit. With your thumbs, press the
marked areas on the sides of the unit. The top and
bottom covers should separate. You can use a small
screwdriver to pry open the box; Insert the screw-
driver into the slot at an angle. Gently lift the handle
so that the tip of the tool levers downward. Repeat
this procedure for all the marked areas.
Warning
Do not insert the screwdriver straight into the middle of
the slot; this may break off the prongs that secure the
covers.
2. Set Switch 1 (SW1) to the proper EIA-232 data
rate for your DTE, according to the table below.
SW1 SWITCH POSITIONS RATE
12 3
OFF OFF OFF 600
ON OFF OFF 1200
OFF ON OFF 2400
ON ON OFF 4800
OFF OFF ON 7200
ON OFF ON 9600
OFF ON ON 14,400
ON ON ON 19,200
NOTE: SW1 Switch Position 4 is not connected.
3. Set Switch 2 (SW2) to establish synchronous
or asynchronous operation. Use Switch Position 1
of SW2 to choose either sync or async operation:
• Switch Position 1 OFF = SYNC
• Switch Position 1 ON = ASYNC
4. If you select the asynchronous mode, you will need
to set the Rate Adapter/64 to accommodate the
proper character length (including start and stop
bits). Use Switch Positions 2 and 3 of SW2 to set
async data character length.
SW2 SWITCH POSITIONS TOTAL BITS
23
OFF ON 8 bits
ON ON 9 bits
OFF OFF 10 bits
ON OFF 11 bits
NOTE: SW2 switch position 4 is not connected.
5. Close the unit by pressing both halves together.
6. Plug the connector into the AC power supply.
7. Plug the AC power supply into a power outlet.
8
RATE ADAPTER/64
9
CHAPTER 3: Installation
Figure 1. Rate Adapter/64 connected to an ISDN terminal
Figure 2. Rate Adapter/64 connected to an
ISDN U interface multiplexor
Figure 3. Rate Adapter/64 strapping diagram.
SW1
ON
OFF
BAUD RATE N.C.
SW2
OFF ON
ASYNC/SYNC
NO. OF BITS
N.C.
DATA
TERMINAL
RATE ADAPTER/64
(IC610A , IC612A)
ISD/U TERMINAL
ADAPTER
PSTN
PSTN
ISD/U BRI
LINE
Data
Terminal
Rate
Adapter/64 Rate
Adapter/64 Data
Terminal
Multiplexors
Ce manuel convient aux modèles suivants
1
Table des matières
Autres manuels Black Box Adaptateur
Black Box
Black Box Multi-Function Line Driver Manuel utilisateur
Black Box
Black Box LE073A-R2 Manuel utilisateur
Black Box
Black Box Twinax Baluns Manuel utilisateur
Black Box
Black Box AC1055A Manuel utilisateur
Black Box
Black Box VGA-USB Adapter Manuel utilisateur
Black Box
Black Box ME890AE-R2 Manuel utilisateur
Black Box
Black Box EVNHDMI-VGA-MF Manuel utilisateur
Black Box
Black Box TCA-232 Manuel utilisateur
Black Box
Black Box MicroConverter G.703 Manuel utilisateur
Black Box
Black Box CL512A-F Manuel utilisateur
Black Box
Black Box LG9230CtX-32 Manuel utilisateur
Black Box
Black Box USB–DVI/VGA Adapter Manuel utilisateur
Black Box
Black Box AC346A USB to HD Pro Manuel utilisateur
Black Box
Black Box IC138A-R2 Manuel utilisateur
Black Box
Black Box 2-Port RS-232/422/485 Manuel utilisateur
Black Box
Black Box IC461A Manuel utilisateur
Black Box
Black Box IC1101A Manuel utilisateur
Black Box
Black Box USB Solo-E Manuel utilisateur
Black Box
Black Box IC441A Manuel utilisateur
Black Box
Black Box LT098A Manuel utilisateur
