BinTec TBC1-1VDSL2-1 Manuel utilisateur

TBC1-1VDSL2-1 card

Installation Manual

bintec elmeg Manual

TBC1-1VDSL2-1 card 1

Legal Notice

Warranty

This publication is subject to change.

bintec elmeg offers no warranty whatsoever for information contained in this manual.

bintec elmeg is not liable for any direct, indirect, collateral, consequential or any other damage connected to the de-

livery, supply or use of this manual.

Manual bintec elmeg

2TBC1-1VDSL2-1 card

Table of Contents

Chapter1 AboutThisManual................................. 1

1.1 SupportedDevices................................... 1

1.2 Warningandnotes................................... 1

1.3 Who should read this manual? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

1.4 Whatisinthismanual?................................. 1

1.5 How is the information organized? . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

1.6 TechnicalSupport ................................... 1

1.7 RelatedDocumentation................................. 2

Chapter 2 TBC1-1VDSL2-1 expansion card . . . . . . . . . . . . . . . . . . . . . . . . . 3

2.1 TBC1-1VDSL2-1 expansion card: Characteristics . . . . . . . . . . . . . . . . . . . . . . 3

2.2 TBC1-1VDSL2-1 expansion card: Connectors . . . . . . . . . . . . . . . . . . . . . . . 4

Chapter 3 Installing the TBC1-1VDSL2-1 expansion card . . . . . . . . . . . . . . . . . . 5

3.1 Requirements prior to installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

3.1.1 Determining the firmware file . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

3.2 Installing or replacing the TBC1-1VDSL2-1 expansion card. . . . . . . . . . . . . . . . . . 5

Chapter 4 LEDs and connector pinouts: Description . . . . . . . . . . . . . . . . . . . . . 6

4.1 TBC1-1VDSL2-1 expansion card: LEDs . . . . . . . . . . . . . . . . . . . . . . . . . . 6

4.2 Connectorpinouts ................................... 6

4.2.1 RJ-45Connector.................................... 6

Chapter5 Compliance..................................... 8

5.1 ManufacturerInformation................................ 8

5.2 SafetyWarnings.................................... 8

5.3 WEEEInformation................................... 8

5.4 REACH........................................ 9

5.5 EC Declaration of Conformity. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

5.6 CEmarking...................................... 9

bintec elmeg Table of Contents

TBC1-1VDSL2-1 card i

Table of Contents bintec elmeg

ii TBC1-1VDSL2-1 card

Chapter 1 About This Manual

This installation guide contains step by step instructions on how to correctly install, uninstall and replace the

TBC1-1VDSL2-1 expansion card in bintec RM3000 / RM5000 / RM7000 routers.

1.1 Supported Devices

The information provided in this installation manual only applies to the TBC1-1VDSL2-1 card.

1.2 Warning and notes

Observe the warnings and instructions set forth in this manual to avoid any injuries or damage during installation and

maintenance. Please follow the security procedures and guidelines when working near electrical equipment. The

warnings and notes are provided in each chapter as appropriate.

1.3 Who should read this manual?

This manual should be read by installers and network administrators who need to install, configure or maintain net-

works. This guide assumes that the installer is familiar with network electronics and technologies.

1.4 What is in this manual?

This installation guide contains the following information:

• A description of the general characteristics of the TBC1-1VDSL2-1 expansion

card.

• A description of the steps to carry out in order to install the TBC1-1VDSL2-1

card in bintec RM3000 / RM5000 / RM7000 routers.

• A description of the TBC1-1VDSL2-1 expansion card LEDs and connector pin-

outs.

1.5 How is the information organized?

This document aims to provide all the information necessary to install the TBC1-1VDSL2-1 expansion card in the

bintec RM3000 / RM5000 / RM7000 router family.

•TBC1-1VDSL2-1 expansion card characteristics.

•TBC1-1VDSL2-1 expansion card connectors.

• Requirements prior to installation.

• Installing the TBC1-1VDSL2-1 expansion card.

1.6 Technical Support

bintec elmeg offers a technical support service. Device software can be upgraded on a regular basis for maintenance

purposes and for new features.

Contact information:

Web: http://www.bintec-elmeg.com

Tel. No.: +49 - 911 - 9673 0

Fax: +49 - 911 - 688 0725

bintec elmeg 1 About This Manual

TBC1-1VDSL2-1 card 1

Email: support@bintec-elmeg.com

1.7 Related Documentation

bintec Dm569-I bintec RM3000 Installation.

bintec Dm741-I ADSL-VDSL

Note

The manufacturer reserves the right to make changes and improvements to the appropriate features in

both the software and hardware of this product, modifying the specifications of this manual without prior

notice.

The images that show the front and back panels of the device are for information purposes only. Some

small modifications may exist in the actual device.

1 About This Manual bintec elmeg

2TBC1-1VDSL2-1 card

Chapter 2 TBC1-1VDSL2-1 expansion card

This manual focuses on the TBC1-1VDSL2-1 expansion card.

VDSL2 stands for Very high bit rate Digital Subscriber Line version 2, which is defined in the ITU G.993.2 and

G.993.5 standards.

VDSL2 has been developed using the ADSL/ADSL2/ADSL2+ technologies as basis, and the main differences areas

follows:

• Upstream and downstream channel multiplicity.

• Supports up to 200 Mbps, symmetric (profile 30a).

• It only uses FDM mode, EC mode is not defined (echo cancellation or carrier

overlapping).

• Allows for a new encapsulation to be used: PTM.

• Multiple link diagnostics.

For further information on ADSL and VDSL technologies, please see the bintec Dm741-I ADSL-VDSL manual.

Fig. 1: TBC1-1VDSL2-1 card

2.1 TBC1-1VDSL2-1 expansion card: Characteristics

The main characteristics of the TBC1-1VDSL2-1 expansion card are as follows

TBC1-1VDSL2-1 card: xDSL characteristics

Ports One RJ-45 VDSL/ADSL port.

ADSL

Standards ANSI:

• T1.413 Issue 2.

ITU-T G.991.1 (G.DMT):

• Annex A: Full Rate ADSL over POTS.

ITU-T G.991.2 (G. Lite) Lite ADSL over POTS.

G.992.3 (ADSL2):

• Annex A: ADSL2 over POTS.

• Annex L: RE-ADSL2 over POTS,

• Annex M: ADSL2 with extended upstream over POTS.

G.992.5 (ADSL2+):

• Annex A: ADSL2+ over POTS.

• Annex M: ADSL2+ with extended upstream over POTS.

bintec elmeg 2 TBC1-1VDSL2-1 expansion card

TBC1-1VDSL2-1 card 3

Downstream Speed 27 Mbps.

Upstream Speed 3 Mbps.

Transfer Mode ATM (Asynchronous Transfer Mode).

Other characteristics Dying Gasp:

• ITU G.991.2 standard recommendation.

VDSL

Standards ITU-T G.993.2 (Annex A and B):

• Profiles: 8a, 8b, 8c, 8d, 12a, 12b, 17a

ITU-T G.993.5 (vectoring).

Downstream Speed Up to 100 Mbps.

Upstream Speed Up to 50 Mbps.

Transfer Mode PTM (Packet Transfer Mode ).

Other characteristics PTM Transmission Convergence (PTM-TC):

• G.993.2 Annex K.

Dual-Latency supported.

Dying Gasp:

• ITU G.991.2 standard recommendation.

2.2 TBC1-1VDSL2-1 expansion card: Connectors

Figure 2 shows the front board of the TBC1-1VDSL2-1 card:

Fig. 2: Front of the TBC1-1VDSL2-1 card

The front board elements are as follows:

Elements table for the front of the TBC1-1VDSL2-1 card

Item Description

AStatus LED

B Link LED

C xDSL port

2 TBC1-1VDSL2-1 expansion card bintec elmeg

4TBC1-1VDSL2-1 card

Chapter 3 Installing the TBC1-1VDSL2-1 expansion card

This chapter provides information on how to install and uninstall the TBC1-1VDSL2-1 expansion card in bintec

RM3000 / RM5000 / RM7000 routers.

This information includes:

• Requirements prior to installation.

• Installing or replacing a TBC1-1VDSL2-1 expansion card.

3.1 Requirements prior to installation

To configure the card, you must be able to access the bintec RM3000 / RM5000 / RM7000 router through a console

or a Telnet connection. For further information, please see the Connecting for configuration section under the bintec

Dm569-I bintec RM3000 Installation manual.

For the TBC1-1VDSL2-1 expansion cards to operate properly, you must load the appropriate firmware file for each

card in the router.

If the firmware has not been loaded in the device prior to installing the card, you can still find out what firmware file

you need.

3.1.1 Determining the firmware file

There are two options to determine the firmware file needed for the installed xDSL card:

3.1.1.1 FTP " quote site listfirmwares" command

The FTP command quote site listfirmwares returns a list containing the names of the firmware files needed for the

device to operate properly:

ftp> quote site listfirmwares

211 fw000016.bfw

ftp>

3.1.1.2 FTP "system firmwares-required" Monitoring command

The system firmwares-required monitoring command displays the same information as the previous command, but

in the local console:

+system firmwares-required

List of required firmwares for detected hardware

------------------------------------------------

Filename Description Version/Subv

------------- ---------------------------- ---------------

fw000016.bfw Lantiq VRX288 TSS-mode v1.0

Once the necessary firmware file has been detected, load it onto the device through an FTP connection.

For further information on how to load firmware files in the router, please see the bintec Dm 748-I Software Updating

manual.

3.2 Installing or replacing the TBC1-1VDSL2-1 expansion card.

To install or replace a TBC1-1VDSL2-1 card, please see the Expansion Slot section under the bintec Dm569-I

bintec RM3000 Installation manual.

bintec elmeg 3 Installing the TBC1-1VDSL2-1 expansion card

TBC1-1VDSL2-1 card 5

Chapter 4 LEDs and connector pinouts: Description

This chapter provides information on the TBC1-1VDSL2-1 expansion card LEDs and connector pinouts.

4.1 TBC1-1VDSL2-1 expansion card: LEDs

The TBC1-1VDSL2-1 expansion card for bintec RM3000 / RM5000 / RM7000 routers has three LEDs: STATUS and

LINK.

Fig. 3: TBC1-1VDSL2-1 card

LEDs table of the TBC1-1VDSL2-1 card

Item State

A (Status) OFF: card not detected.

ON: card detected (firmware loaded).

B (Link) OFF: disabled.

Slow blinking: active.

Fast blinking: negotiating.

Steady: synchronized.

4.2 Connector pinouts

The TBC1-1VDSL2-1 expansion card has one RJ-45 connector.

4.2.1 RJ-45 Connector

The following figure shows the RJ-45 connector pinouts.

Fig. 4: xDSL connector

Fig. 5: RJ-45 Connector Pinouts

The following table display the information associated to each connector pinout:

4 LEDs and connector pinouts: Description bintec elmeg

6TBC1-1VDSL2-1 card

Table des matières

Autres manuels BinTec Matériel informatique

BinTec

BinTec X5800 Manuel utilisateur

BinTec

BinTec X4100 Manuel utilisateur

Manuels Matériel informatique populaires d'autres marques

EMC2

EMC2 VNX Series Manuel du propriétaire

Panasonic

Panasonic DV0PM20105 Manuel utilisateur

Mitsubishi Electric

Mitsubishi Electric Q81BD-J61BT11 Manuel utilisateur

Gigabyte

Gigabyte B660M DS3H AX DDR4 Manuel utilisateur

Raidon

Raidon iT2300 Manuel utilisateur

National Instruments

National Instruments PXI-8186 Manuel utilisateur

Hauppauge

Hauppauge WinTV-HVR-2250 Manuel utilisateur

Kontron

Kontron CP6002 Manuel utilisateur

Manhattan

Manhattan 702843 Manuel utilisateur

Aphex

Aphex 230 Manuel utilisateur

AMD

AMD Phenom II Manuel d'exploitation

Intel

Intel NUC 12 Pro Manuel utilisateur

dbx

dbx Zone Pro 1260 Manuel utilisateur

Galaxy

Galaxy GHDX2-2430S-24F4D Manuel utilisateur

Intel

Intel AXXRMFBU4 Manuel utilisateur

Kontron

Kontron DIMM-PC/MD Manuel utilisateur

ST X-NUCLEO-SAFEA1B Mode d'emploi

STEINWAY LYNGDORF

STEINWAY LYNGDORF SP-1 Manuel utilisateur