Billy Goat KV600SP Manuel utilisateur

Part No 891061 - 1 - Form No F052209A

KV HOSE KIT P/N 891125

BILLY GOAT KV HOSE KIT

(P/N 891125)

PURPOSE: To allow for vacuuming in hard to reach places.

Part No 891061 - 2 - Form No F052209A

KV HOSE KIT P/N 891125

INSTALLATION:

Step 1. Attach nozzle wear guards.

1. Disconnect spark plug wire.

2. Raise the nozzle height to its highest position and

secure the unit from moving.

3. Remove the two bolts, nuts and washers on the

sides of the nozzle that hold the reinforcement

bracket on the interior of the nozzle. Do not discard

the old hardware.

4. Slide the guards into place then secure the guards

with the hardware previously removed.

5. Tighten the hardware using two 7/16” wrenches.

6. Repeat steps 2 through 5 on the left hand side.

WARNING!Improper attachment of

nozzle holder can cause damage to the

hose from hot exhaust exiting the engine.

Step 2. Attach the hose nozzle bracket (item

10).

1. Remove the two screws on the muffler side of the

top plate. Left side for for Briggs and right side for

Honda (see figure at right). Attach the bracket with the

screws (item 12) provided. Do Not over tighten as this

may strip the screws.

Remove the screws from these two positions

Briggs

Honda

Remove the screws from these two positions

TKV

Remove the screws from these two positions

Part No 891061 - 3 - Form No F052209A

KV HOSE KIT P/N 891125

INSTALLATION: continued

Step 3. Attach coupler (item 8) and nozzle to

hose.

1. Slide the two hose clamps over both ends of the

hose and at one end attach the coupler to the hose

using a 5/16” nut driver. Note: the hose is attached to

the end of the coupler without the pin. Make sure the

hose is completely seated next to the plate and secure it

with one of the hose clamps. Next attach the nozzle with

the handle to the other end of the hose by sliding it into

the hose with enough distance to allow the clamp to hold

the hose to the nozzle securely then tighten the clamp.

Step 4. Attach the hose-holding bar (item 11).

1. Connect loop on right side of wire bracket hose

retainer to the upper handle of the machine, pull left side

of wire until the loop will go over the upper handle.

2. Attach the blocker plate to the wire bracket hose

retainer when not in use by sliding the wide slot over the

top of the wire bracket and then sliding it down to it’s

resting position.

Step 5. Attach hose coupler to nozzle housing.

1. Slide the hose coupler into the nozzle housing. Slide it

in at an angle and insert one of the pins into the slot,

then rotate and slide the other pin through, this will allow

the coupler to sit flush.

2. Reconnect spark plug.

Step 6. Hose placement when not in use.

1. With the hose off to the left side of the machine (on

the Honda model), drape the hose over the hose wire

bracket holder and rest the nozzle into the nozzle

bracket holder. Note: The hose should be wrapped

around the right side of the machine with Briggs models.

Use this method of transporting the hose when not in

use (See picture right). Warning: Do not let the hose

come into contact with hot parts of the engine, as this

will damage your hose and is not covered by the

warranty.

Part No 891061 - 4 - Form No F052209A

KV HOSE KIT P/N 891125

Operation

1. Simply slide the plate (item 10) onto the wear guards

till the front is flush with the front edge of the nozzle. To

remove simply apply pressure to the outside edges at

the wear brackets and slide forward. This will allow

suction through the hose when attached rather than the

nozzle. To remove the plate push outward on the tabs

and this will allow you to slide the plate off.

ITEM NO. PART

NUMBER DESCRIPTION QTY.

1 891029 NOZZLE GUARD RH 1

2 891031 NOZZLE GUARD LH 1

5 891044 HOSE 4" x 7' CLEAR PVC GREEN HELIX 1

6 800896 CLAMP HOSE 4" 2

7 800803 NOZZLE ASSY 4" 1

8 890040 HOSE COUPLER 1

9 891122 NOZZLE RETAINER BRACKET 1

10 891030 NOZZLE BLOCKING KV 1

11 890025 WIRE BRACKET HOSE RETAINER 1

12 891146 SCREWCAP 1/4-20 X 1" HWH TYPE F 2

Reference hardware

3 8041006 SCREWCAP 1/4-20 X 1" 4

4 8160001 NUT LOCK 1/4-20 4

Part No 891061 - 5 - Form No F052209A

KV HOSE KIT P/N 891125

HOSE CARE & SHIPPING INFORMATION

SHIPPING TAG

IMPORTANT NOTICE

This merchandise was in perfect condition when packed and shipped.

Unpack immediately and check for damage.

Place any damage claim with delivering carrier and have inspection made at once.

Our warranty covers manufacturing defects only.

DO NOT RETURN TO SHIPPER.

SHIPPER-WARNING

TOP LOAD ONLY TO PREVENT SHIPPING DAMAGE.

HOSE CARE

ATTENTION!

•Hoses are wear items and are only warranted against manufactures

defects. Hose must be inspected for shipping damage before using.

•Proper care is required to prevent damage. Operators should be cautious

and keep the hose as straight as possible when vacuuming to not only

help prevent clogging, but also to also help prevent abnormal wear to the

sides of the hose. Rotate hose periodically to extend life. (Suggest ¼ turn

every 20 hours.)

•Hose that has been exposed to extreme temperatures, chemicals,

abrasive material or that have been run over will not be warranted.

•The 8” (810523), 10” (810705), and the 12” (790148) hoses have internal

wrapping must be installed so the overlapping edges face in the direction

of airflow. These hoses are marked by the manufacturer with an airflow

direction arrow. Installing the hose with the airflow direction arrow

reversed will cause premature failure and VOIDS the warranty.

Autres manuels pour KV600SP

Table des matières

Autres manuels Billy Goat Ventilateur

Billy Goat

Billy Goat QUIET BLOW QB1601 Instructions d'installation

Billy Goat

Billy Goat QUIET BLOW QB1100HPN Manuel utilisateur

Billy Goat

Billy Goat F902S Manuel utilisateur

Billy Goat

Billy Goat QUIET BLOW QB551 Manuel utilisateur

Billy Goat

Billy Goat F800 Manuel utilisateur

Billy Goat

Billy Goat F902SPH Manuel utilisateur

Billy Goat

Billy Goat F601S Manuel utilisateur

Billy Goat

Billy Goat P / N 440120 Manuel utilisateur

Billy Goat

Billy Goat F1002SPV Manuel utilisateur

Billy Goat

Billy Goat F1301H Manuel utilisateur

Billy Goat

Billy Goat QUIET BLOW QB881 Manuel utilisateur

Billy Goat

Billy Goat MV VACUUM PUSH EU MV601EU Manuel utilisateur

Billy Goat

Billy Goat Z FORCE FZ1300H Manuel utilisateur

Billy Goat

Billy Goat F1002V Manuel utilisateur

Billy Goat

Billy Goat FORCE 601XEU Manuel utilisateur

Billy Goat

Billy Goat KV600SP Manuel utilisateur

Billy Goat

Billy Goat FORCE F601V Manuel utilisateur

Billy Goat

Billy Goat F601S Manuel utilisateur

Billy Goat

Billy Goat Force Blower Manuel utilisateur

Billy Goat

Billy Goat QUIET BLOW QB1004 Instructions d'installation

Billy Goat

Billy Goat FORCE F601V Manuel utilisateur

Billy Goat

Billy Goat QUIET BLOW QB1601 Instructions d'installation

Billy Goat

Billy Goat F902SPS Manuel utilisateur

Billy Goat

Billy Goat BLOWER QB882 Instructions d'installation

Manuels Ventilateur populaires d'autres marques

Weed Eater

Weed Eater VS2000BV Manuel utilisateur

KRAUSMANN

KRAUSMANN U37020-00 Manuel utilisateur

Bosch

Bosch ALB 36 LI Manuel utilisateur

Cub Cadet

Cub Cadet HB425 Manuel utilisateur

GreenWorks Pro

GreenWorks Pro BLB482 Manuel utilisateur

ARIETE

ARIETE 2768 Manuel utilisateur

NuTone

NuTone 331H Manuel utilisateur

GÜDE

GÜDE GLB 200 18 Li-Ion Manuel utilisateur

I.VA.CO.

I.VA.CO. SC Series Mode d'emploi

DeWalt

DeWalt DCE100 Manuel utilisateur

Becker

Becker SV 7.330 Manuel utilisateur

Metabo

Metabo AG 18 Pro Manuel utilisateur

Desa

Desa GA3650TB Manuel utilisateur

Echo

Echo Power Blower PB-230LN Manuel utilisateur

Echo

Echo PB-413H Manuel utilisateur

Black & Decker

Black & Decker BV3100 Manuel utilisateur

Ryobi

Ryobi RY08570 Manuel utilisateur

Haaga

Haaga 355 Manuel utilisateur