Biamp TesiraFORTE Manuel utilisateur

TesiraFORTÉ Fan Replacement

This article will walk you through the process to replace the fan inside of a TesiraFORTÉ unit. Please read this

document carefully in its entirety before beginning as there are delicate components inside the TesiraFORTÉ.

Locate the fan

The fan is located at the front of the Chassis for the TesiraFORTÉ, on the left side of the unit if you are looking straight

on at the device. Make sure that all cables are disconnected from the unit before you remove the Chassis from the rack,

and verify that the device has been powered down.

Open the chassis

Using a Phillips-head screwdriver, remove the three screws shown below from the back of the TesiraFORTÉ chassis.

Lift off the top plate to remove it and set aside.

Remove the front panel

Before you remove the front panel, make note of the 2 ribbon cables on the TesiraFORTÉ. Take extra care to avoid

damaging these two cables. If they are damaged, the front panel LED screen may no longer function.

Unplug the white ribbing cable, grip gently and pull straight out of the connector.

Unclasp the front panel brackets and gently slide the front panel forward. Exercise caution to avoid damaging either

ribbon cable. Once the front panel is removed, rest it face side down to reduce the change of damaging the cables.

Remove the fan

Now that the fan is exposed, remove the screws holding the fan housing in place. Note that the fan is attached to the

main board on the TesiraFORTÉ as well. Disconnect this carefully to avoid damaging the connector on the board.

Remove the screws from the front panel that hold the fan housing in place.

Push firmly at the bottom of the fan and will slide out under the metal lip of the chassis. Ensure that you press on the

bottom of the fan housing and not the fan itself.

Remove the fan from its housing by removing the two retainer screws.

Install the new fan

Attach the new fan to the housing using the same screws removed in the previous step.

Insert the fan assembly back into the TesiraFORTÉ by hooking the fan underneath the lip of the TesiraFORTÉ frame

and push inward on the bottom of the assembly to move it into place. This will require firm pressure but not enough to

damage any components.

Replace the front panel

Take note of the two holes in the front plate. These line up with the two ribbon cables attached to the front

panel assembly.

Line up the front panel with the plate and press it back into place until the front panel latches are engaged. Use caution

to avoid damage to the ribbon cables. If they are bent excessively or pinched, the front panel will likely no longer

function.

Reconnect the white ribbon cable to its receiving connector located on the main circuit board. Press straight down and

take care to not bend the cable to the point of damage. The amount of pressure needed should be firm and steady, but

not excessive to where it will damage the cable.

Close the chassis

Slide the top panel back into place. All metal tabs should be on the inside of the chassis leaving the outside smooth.

Replace the three screws to secure the top panel and the process is complete.

Autres manuels pour TesiraFORTE

Table des matières

Autres manuels Biamp Matériel informatique

Biamp

Biamp Devio SCX Manuel utilisateur

Biamp

Biamp MSP11 Manuel utilisateur

Biamp

Biamp ADVANTAGE NMP200 Manuel d'utilisation et d'entretien

Biamp

Biamp VOCIA VI-6 Manuel utilisateur

Biamp

Biamp QtPro Series Manuel utilisateur

Biamp

Biamp Nexia Series Manuel utilisateur

Biamp

Biamp Tesira SERVER Manuel utilisateur

Biamp

Biamp ADVANTAGE NMP200 Manuel utilisateur

Manuels Matériel informatique populaires d'autres marques

EMC2

EMC2 VNX Series Manuel du propriétaire

Panasonic

Panasonic DV0PM20105 Manuel utilisateur

Mitsubishi Electric

Mitsubishi Electric Q81BD-J61BT11 Manuel utilisateur

Gigabyte

Gigabyte B660M DS3H AX DDR4 Manuel utilisateur

Raidon

Raidon iT2300 Manuel utilisateur

National Instruments

National Instruments PXI-8186 Manuel utilisateur

Hauppauge

Hauppauge WinTV-HVR-2250 Manuel utilisateur

Kontron

Kontron CP6002 Manuel utilisateur

Manhattan

Manhattan 702843 Manuel utilisateur

Aphex

Aphex 230 Manuel utilisateur

AMD

AMD Phenom II Manuel d'exploitation

Intel

Intel NUC 12 Pro Manuel utilisateur

dbx

dbx Zone Pro 1260 Manuel utilisateur

Galaxy

Galaxy GHDX2-2430S-24F4D Manuel utilisateur

Intel

Intel AXXRMFBU4 Manuel utilisateur

Kontron

Kontron DIMM-PC/MD Manuel utilisateur

ST X-NUCLEO-SAFEA1B Mode d'emploi

STEINWAY LYNGDORF

STEINWAY LYNGDORF SP-1 Manuel utilisateur