BGS technic 6667 Manuel utilisateur

BGS technic KG

Bandwirkerstr. 3

D-42929 Wermelskirchen

Tel.: 02196 720480

Fax.: 02196 7204820

mail@bgs-technic.de

www.bgstechnic.com

BGS 6667

Clutch Aligning Tool Set for Trucks

TOOLS

1 Centering mandrel (clutch disc), 42 - 52 mm

2 Centering mandrel (clutch disc), 36 - 45 mm

3 Centering sleeve (pilot bearing), 30 mm

4 Centering sleeve (pilot bearing), 27 mm

5 Centering sleeve (pilot bearing), 25 mm

6 Centering sleeve (pilot bearing), 20 mm

7 Replacement O-rings

INTENDED USE

This tool set is required when replacing truck single and double clutch discs and allows a professional

centering of clutch discs.

SAFETY INFORMATIONS

•Read carefully the instructions before working with this tool set.

•Do not use this tool set for other purpose for which it is designed.

•Observe the general safety instructions for garages.

•Keep your work area tidy and clean. Areas or corridors which are untidy increase the risk of injury.

•Lifting of vehicles only allowed on the special lifting points.

•Before starting the work under a vehicle always ensure that it is adequately supported by axle

stands or ramps. Chock wheels and ensure that the hand brake is firmly applied.

•Always use approved eye protection, especially when working under vehicles.

•Ensure a secure and well-gripped stance during fitting.

•Check the condition of the tool regularly and do not use it if it is damaged.

•Make sure the tool is properly mounted.

•This manual serves as a brief guide and does not replace a workshop manual. Always refer to the

vehicle-specific service literature, particularly the technical data such as torque values and

instructions for disassembly/assembly, etc..

•Keep children and other unauthorized persons away from the work area.

•Do not let children play with the tool or its packaging and keep this tool out of the reach of

children.

BGS technic KG

Bandwirkerstr. 3

D-42929 Wermelskirchen

Tel.: 02196 720480

Fax.: 02196 7204820

mail@bgs-technic.de

www.bgstechnic.com

USE

Choose a suitable centring sleeve (3 - 6), it must fit in the

crankshaft bore / pilot bearing.

Choose a suitable centring mandrel (1 / 2) and install the

centring sleeve (3 - 6) onto the thread of the centring mandrel.

Insert the clutch centring mandrel into the clutch hub and fix

the centring mandrel in the clutch hub by turning the knurled

screw clockwise.

Centre the clutch disc with centring sleeve in the crankshaft

bore (pilot bearing) and install the clutch pressure plate.

Attention: Make sure that the clutch disc is mounted in the

proper position.

Loosen the centring mandrel by turning the knurled screw anti-

clockwise and remove it from the clutch hub.

Table des matières

Autres manuels BGS technic Outils

BGS technic

BGS technic 6890 Manuel utilisateur

BGS technic

BGS technic 1778 Manuel utilisateur

BGS technic

BGS technic 9655 Manuel utilisateur

BGS technic

BGS technic BGS 8540 Manuel utilisateur

BGS technic

BGS technic 74428 Manuel utilisateur

BGS technic

BGS technic 62604 Manuel utilisateur

BGS technic

BGS technic 3325 Manuel utilisateur

BGS technic

BGS technic Drive Manuel utilisateur

BGS technic

BGS technic 8743 Manuel utilisateur

BGS technic

BGS technic 8849 Manuel utilisateur

BGS technic

BGS technic 8856 Manuel utilisateur

BGS technic

BGS technic 8651 Manuel utilisateur

BGS technic

BGS technic 1768 Manuel utilisateur

BGS technic

BGS technic 8231 Manuel utilisateur

BGS technic

BGS technic 8570 Manuel utilisateur

BGS technic

BGS technic BGS 2999 Manuel utilisateur

BGS technic

BGS technic 62637 Manuel utilisateur

BGS technic

BGS technic 70345 Manuel utilisateur

BGS technic

BGS technic 3361 Manuel utilisateur

BGS technic

BGS technic 9323 Manuel utilisateur

BGS technic

BGS technic 1721 Manuel utilisateur

BGS technic

BGS technic 9605 Manuel utilisateur

BGS technic

BGS technic 8527 Manuel utilisateur

BGS technic

BGS technic 149 Manuel utilisateur

Manuels Outils populaires d'autres marques

Martor

Martor SECUNORM 175 Manuel utilisateur

ERKCO

ERKCO 1000 Manuel utilisateur

jbc

jbc N4473 Manuel utilisateur

FEINMETALL

FEINMETALL FZWZ-SET-001 Manuel utilisateur

Worx Professional

Worx Professional Sonicrafter WU676 Manuel utilisateur

Gage Bilt

Gage Bilt GB713SH Manuel utilisateur

Hilti

Hilti DX 9-ENP Manuel utilisateur

norbar

norbar NORTRONIC 34399 Manuel utilisateur

Makita

Makita DHR241 Manuel utilisateur

Motor Guard

Motor Guard JMB-1250 Manuel utilisateur

Power Adhesives

Power Adhesives 805-12 Manuel utilisateur

Clemco

Clemco 24189 Manuel utilisateur

VVG

VVG VNG 903 Series Manuel utilisateur

Hilti

Hilti FX 3-A Manuel utilisateur

Grizzly

Grizzly H6472 Manuel utilisateur

axing

axing BWZ 5-02 Manuel utilisateur

Dh-Robotics

Dh-Robotics RGI-100 Comment utiliser

Goobay

Goobay 97790 Manuel utilisateur