BGS technic 3213 Manuel utilisateur
Art. 3213
8-piece Air Hammer Kit
Technical Data
Chisel shank: Ø 10 mm
Chisel shank length: 133 mm
Blow per minute: 4500
Working pressure: 90PSI
Air consumption: 4CFM (90PSI)
Air Inlet: 1/4“ PT
Stroke: 41 mm
Noise: LpA: 84 dB (A)
LwA: 95 dB (A)
Vibration: ahd = 9,4 m/s²
K = 1,5 m/s²
Weight: 1,1 kg
Please read these instructions carefully before use or maintain the air tool described. Keep
instructions for future reference.
Description
This air hammer is designed for cutting through rusted metal or bolts and removing mortar from
cement blocks or bricks.
General Safety
1. This air hammer is a part of a high pressure system. Do not exceed maximum operating pressure
of the air tool (90 PSI – 6,2 BAR). The hammer could explore and result in death or serious injury.
2. Disconnect the air drill from air compressor before changing tools or accessories, servicing and
during non operation.
3. Always ear safety glasses and using hearing protection during operation.
4. Do not wear loose fitting clothing and jewelry which may become caught in moving parts and
result in serious injury.
5. Do not depress trigger when connecting the air hose.
6. Never trigger the tool when not applied to a work object. Accessories must be securely attached.
7. Make sure spring retainer, all connections are secure and check air hoses for weak or worn
condition before each use.
8. WARNING !!! Disconnect air supply before installing or any maintenance notes.
Maintenance Tips
This air hammer requires lubrication BEFORE initial use and BEFORE and AFTER each additional
use throughout its life.
1. WARNING !!! Disconnect the air hammer from the air supply and hold the tool upside down.
2. Pull the trigger, put a half teaspoon of air tool oil into the air inlet.
3. Reconnect the air hammer to the air supply and run the hammer for 20 seconds.
Cover the exhaust port with a towel and run for 20 seconds. Oil will discharge from the rear exhaust
port when air pressure is applied. Any excess oil in the motor is immediately expelled from the
exhaust port.
WARNING !!! Always direct exhaust port away from people or objects.
Operations
Before use, drain water out of air compressor tank and condensation from air lines. After clearing air
compressor moisture and lubricating the air
hammer, connect it to an air hose of a recommended compressor.
1. Remove the spring retainer to load a chisel. Always tighten the spring retainer well before use.
WARNING !!! Use attachments designed for use with air tools. Do not use damaged attachments.
2. Depress the trigger to operate. Always hold the hammer well during operation to avoid injury.
Air Supply
Air supply MUST be greater than air requirement of the tool, Recommended air compressor is 3/4HP.
Air Hose: Using 3 m or 7,5 m long with 5 mm inside diameter and 1/4PT threads is recommended.
However, hoses longer than 7,5 m should use 10 mm even 12 mm inside diameter. For proper
performance and more convenience. Using fittings or air hoses which are too small can create a
pressure drop and reduce the power of the air hammer.
WARNING !!! Keep hoses away from heat, oil and sharp edges. Replace any hose that is damaged,
weak or worn. Never carry a tool by the hose or pull the hose to move the tool or a compressor.
The use of air filters and air line lubricators is recommended.
Storage
The air hammer must be lubricated before storage. Follow the lubrication instructions. Only run for 3
seconds instead of 20 seconds because more oil needs to remain in the tool when storing.
SW-Stahl und Werkzeugvertriebs GmbH Tel. +49 (0) 2191 / 46438-0
F56essartSresukreveL ax +49 (0) 2191 / 46438-40
ed.lhatsws@ofni:liaM-EdiehcsmeR79824-D
CE-Erklärung
BGS technic KG
Bandwirkerstr. 3
D-42929 Wermelskirchen
Tel.: 02196 720480
Fax.: 02196 7204820
www.bgstechnic.com
Wir erklären in alleiniger Verantwortung, dass die Bauart des Produktes:
We declare that the following designated product:
Nous déclarons sous propre responsabilité que ce produit:
Declaramos bajo nuestra sola responsabilidad que este producto:
folgenden einschlägigen Bestimmungen entspricht:
complies with the requirements of the:
est en conformité avec les réglementations ci-dessous:
esta conforme a las normas:
Angewandte Normen:
Norme appliquée:
Normas aplicadas:
ppa.
Frank Schottke, Prokurist
BGS technic KG, Bandwirkerstrasse 3, D-42929 Wermelskirchen
Wermelskirchen, den
EU-KONFORMITÄTSERKLÄRUNG
EC DECLARATION OF CONFORMITY
DÉCLARATION„CE“ DECONFORMITE
DECLARATION DE CONFORMIDAD UE
Druckluft-Meisselhammer-Satz (Art. 3213)
Air Hammer
Marteau à piquer pneumatique
Neumática martillo cincelador
Machinery Directive 2006/42/EC
EN ISO 11148-4:2012
Verification No.: 16081635C-S / WFH-1040
Test Report No.: 2011-16-70-16-PB001
16.06.2017
Autres manuels pour 3213
1
Table des matières
Autres manuels BGS technic Outils électriques
BGS technic
BGS technic 8301 Manuel utilisateur
BGS technic
BGS technic 74267 Manuel utilisateur
BGS technic
BGS technic 8928 Manuel utilisateur
BGS technic
BGS technic 9948 Manuel utilisateur
BGS technic
BGS technic 3650 Manuel utilisateur
BGS technic
BGS technic 8653 Manuel utilisateur
BGS technic
BGS technic 8495 Manuel utilisateur
BGS technic
BGS technic 62674 Manuel utilisateur
BGS technic
BGS technic 1708 Manuel utilisateur
BGS technic
BGS technic BGS 6705 Manuel utilisateur
BGS technic
BGS technic 9942 Manuel utilisateur
BGS technic
BGS technic 9572 Manuel utilisateur
BGS technic
BGS technic 3201 Manuel utilisateur
BGS technic
BGS technic 7177 Manuel utilisateur
BGS technic
BGS technic BGS 9319 Manuel utilisateur
BGS technic
BGS technic 69505 Manuel utilisateur
BGS technic
BGS technic 3234 Manuel utilisateur
BGS technic
BGS technic 8704 Manuel utilisateur
BGS technic
BGS technic 3243 Manuel utilisateur
BGS technic
BGS technic 8717 Manuel utilisateur
