Benning TA 6 Manuel utilisateur

BENNING TA 6

Operating manual

Translation of the German original version

5190 / 04/2021 en

Legal notice

5190 / 04/2021 enBENNING TA 62

Legal notice

Notes concerning the documentation

Ensure that the applicable documentation is used for this product. For safe handling, knowledge

that is provided in these instructions is required.

The product may only be handled while following this documentation, particularly the safety

instructions and warnings it contains. The personnel must be qualified for the respective task

and have the capability to recognise risks and prevent possible dangers.

Manufacturer and holder of rights

BENNING Elektrotechnik und Elektronik GmbH&Co.KG

Münsterstraße135–137

46397 Bocholt

Germany

Phone: +492871/93‑0

E-Mail: [email protected]

Internet: www.benning.de

Commercial register Coesfeld HRA No. 4661

This document – particularly all of the contents, texts, photographs and graphics that it contains

– are protected by copyright.

No part of this documentation or the associated contents may be reproduced or edited, copied

or distributed using electronic media in any form (printed, photocopied or using any other

method) without express written permission.

Disclaimer

The contents of the documentation has been checked to ensure that it corresponds to the

hardware and software described. Nevertheless, deviations cannot be ruled out, so Benning

cannot guarantee complete correspondence. The contents of this documentation are checked

at regular intervals, and any corrections that are needed are contained in the versions that

follow.

General non-discrimination

Benning is aware of the importance of language with regard to the equality of men and women,

and endeavours to take this into account at all times. To improve readability, we have refrained

from consistently using differentiating formulations.

Table of contents

1 Introduction................................................................................................................................................6

1.1 General notes........................................................................................................................6

1.2 History ...................................................................................................................................7

1.3 Service & support..................................................................................................................8

2 Safety..........................................................................................................................................................9

2.1 Warning system ....................................................................................................................9

2.2 Standards applied .................................................................................................................9

2.3 Symbols used......................................................................................................................10

2.4 Intended use .......................................................................................................................11

2.5 Special types of risks ..........................................................................................................12

3 Scope of delivery.....................................................................................................................................13

4 Device description...................................................................................................................................14

4.1 Device structure ..................................................................................................................14

4.2 Functions.............................................................................................................................15

5 Operation..................................................................................................................................................16

5.1 Testing with an installation tester ........................................................................................16

6 Maintenance.............................................................................................................................................17

6.1 Cleaning the device.............................................................................................................17

7 Technical data..........................................................................................................................................18

8 Disposal and environmental protection ................................................................................................19

Index .........................................................................................................................................................20

5190 / 04/2021 en BENNING TA 6 3

Table of figures

Figure 1 BENNINGTA6 device structure ...................................................................................................... 14

Figure 2 Switch positions of the BENNINGTA6 ............................................................................................ 15

Figure 3 Connecting the BENNINGTA6........................................................................................................ 16

5190 / 04/2021 enBENNING TA 64

List of tables

Table 1 History............................................................................................................................................... 7

Table 2 Symbols on the device...................................................................................................................... 10

Table 3 Symbols used in the operating manual............................................................................................. 10

Table 4 Technical data .................................................................................................................................. 18

5190 / 04/2021 en BENNING TA 6 5

1.1 General notes

Introduction

5190 / 04/2021 enBENNING TA 66

1 Introduction

The BENNINGTA6 measuring adapter described here (in the following only referred to as

“device”) is an optional accessory for the BENNINGIT115, IT130 and IT200 installation

testers. The BENNINGTA6 measuring adapter enables you to perform tests on electrical

installations in compliance with DINVDE0100‑600 (IEC60364‑6) and DINVDE0105‑100

(EN50110) using the corresponding installation tester.

The device ensures safe contact between the BENNING installation tester and the 5-pin 16A

CEEsocket (3P/ N/ PE, 400V, 50Hz) of the electrical installation.

The device supports the following measurements:

• Insulating resistance measurement RISO (L1‑PE, L2‑PE, L3‑PE, N‑PE, L1‑L2, L2‑L3, L3‑L1)

• Loop impedance measurement ZLOOP (L1‑PE, L2‑PE, L3‑PE)

• Line impedance measurement ZLINE (L1‑N, L2‑N, L3‑N, L1‑L2, L2‑L3, L3‑L1)

• RCDtesting

• Phase sequence test, voltage and frequency measurements

Further information

http://tms.benning.de/ta6

On the Internet, you will find the following additional information directly at the specified link or

at www.benning.de (product search):

• Operating manual of the device in several languages

• Further information depending on the device (e.g. brochures, technical reports, FAQs)

1.1 General notes

Target group

This operating manual is intended for the following groups of people:

• Qualified electricians and qualified technical personnel

Required basic knowledge

To understand these operating manual, you will need general knowledge of testing and

measuring equipment. Moreover, you will need basic knowledge of the following issues:

• General electrical engineering

Purpose of the operating manual

This operating manual describes the device and provide you information about how to handle it.

Keep this operating manual in a safe place for later use. Read this operating manual before

handling the device and follow the instructions.

Introduction

1.2 History

5190 / 04/2021 en BENNING TA 6 7

NOTE

Disclaimer of liability

Please make sure that any person using the device has read and understood the instructions of

this operating manual before handling the device and that the instructions are adhered to in all

points. Non-observance of this operating manual might result in product damage, property

damage and/or personal injury.

Benning assumes no liability for damage and malfunctions resulting from the failure to observe

the instructions in this operating manual.

The devices are subject to continuous further development. Benning reserves the right to make

changes to the device’s design, configuration and technology. The information in this operating

manual corresponds to the state of technical knowledge at the time of printing. For this reason,

no claims for certain device characteristics can be derived from the contents of this operating

manual.

Information in this operating manual can be changed at any time without prior notice. Benning is

not obligated to make amendments to this operating manual or to keep it up to date.

Direct any technical questions to Technical Support [}page8].

Trademarks

All trade marks that are used are the property of their respective owners, even if they are not

separately marked as such.

1.2 History

Release number Amendments

04/2021 • Initial release

Table1: History

1.3 Service & support

Introduction

5190 / 04/2021 enBENNING TA 68

1.3 Service & support

Please contact your specialty retailer or the BENNINGServiceCenter for any repair or service

work that might be required.

Technical support

Please contact our Technicalsupport for technical questions on handling the device.

Phone: +49287193-555

Fax: +49287193‑6555

E-Mail: [email protected]

Internet: www.benning.de

Returns management

Easily and conveniently use the BENNING returns portal for a quick and smooth returns

processing:

https://www.benning.de/service-de/retourenabwicklung.html

Phone: +49287193-554

E-Mail: [email protected]

Return address

BENNING Elektrotechnik und Elektronik GmbH & Co. KG

Retourenmanagement

Robert-Bosch-Str. 20

D - 46397 Bocholt

Safety

2.1 Warning system

5190 / 04/2021 en BENNING TA 6 9

2 Safety

2.1 Warning system

This operating manual contains notes that must be taken into consideration for your personal

safety and in order to avoid injuries and damage to property. Warnings about your personal

safety and to prevent personal injuries are marked with a warning triangle. Warnings on sole

prevention of material damage are shown without a warning triangle. The warnings are shown

in descending order depending on the hazard level as follows.

DANGER

Extremely dangerous situation for humans

If you do not pay attention to this warning, irreversible or deadly injuries will occur.

WARNING

Hazard to humans

If you do not pay attention to this warning, irreversible or deadly injuries could occur.

CAUTION

Minor hazard to humans

If you do not pay attention to this warning, minor or moderate injuries could occur.

NOTICE

Danger to property, not to persons

If you do not pay attention to this warning, material damage could occur.

If multiple hazard levels occur, the warning for the highest respective hazard level will be used.

In addition, a warning about personal injuries can also include a warning about material

damage.

2.2 Standards applied

The device has been built and tested in compliance with the following standards and has left the

factory in perfectly safe condition.

• IEC/ DINEN 61010-031 (VDE0411‑031)

2.3 Symbols used

Safety

5190 / 04/2021 enBENNING TA 610

2.3 Symbols used

Symbols on the device

Symbol Meaning

Please observe the information provided in this operating manual in

order to avoid dangers.

CATII Measuring categoryII is applicable to testing and measuring circuits

which are directly connected to user connections (e.g. sockets) of the

low-voltage mains installation.

The device complies with EUdirectives.

At the end of product life, dispose of the unserviceable device via

appropriate collecting facilities provided in your community.

The device is provided with protective insulation (protection classII).

Please observe the operating manual.

Table2: Symbols on the device

Symbols used in the operating manual

Symbol Meaning

General warning

Warning of electric voltage!

(AC) alternating voltage or alternating current

Earth (voltage to earth)

Table3: Symbols used in the operating manual

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Benning Instrument de mesure

Benning

Benning CM 4 Manuel utilisateur

Benning

Benning CM 2-1 Manuel utilisateur

Benning

Benning ST 710 Manuel utilisateur

Benning

Benning Luxmeter B Manuel utilisateur

Benning

Benning PV 1-1 Manuel

Benning

Benning TRITEST Pro Manuel utilisateur

Benning

Benning Sun 2 Manuel utilisateur

Benning

Benning MM 7-2 Manuel utilisateur

Benning

Benning VT 2 Manuel utilisateur

Benning

Benning DB 1 Manuel utilisateur

Benning

Benning CM 8 Manuel utilisateur

Benning

Benning PV 2 Manuel

Benning

Benning CC 4-1 Manuel utilisateur

Benning

Benning CC 2 Manuel utilisateur

Benning

Benning IT 101 Manuel utilisateur

Benning

Benning CM 2 Manuel utilisateur

Benning

Benning IT 100 Manuel utilisateur

Benning

Benning MA 3 Manuel utilisateur

Benning

Benning CM 9-1 Manuel utilisateur

Benning

Benning CM E1 Manuel utilisateur

Benning

Benning CFlex 2 Manuel utilisateur

Benning

Benning CM 1 Manuel utilisateur

Benning

Benning Sun 2 Manuel utilisateur

Benning

Benning CM P1 Manuel utilisateur

Manuels Instrument de mesure populaires d'autres marques

Suaoki

Suaoki D40 Manuel utilisateur

Elster

Elster BK-G1.6 Manuel utilisateur

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manuel

Duratool

Duratool D03128 Manuel utilisateur

Vega

Vega VEGAPULS 65 Manuel utilisateur

Tonghui

Tonghui TH2618B Manuel utilisateur

Tenmars

Tenmars TM-801 Manuel utilisateur

MSR

MSR 145 Manuel utilisateur

TPS

TPS WP-82 Manuel utilisateur

ELMETRON

ELMETRON CP-511 Manuel utilisateur

PCB Piezotronics

PCB Piezotronics 003C30 Manuel utilisateur

Tenma

Tenma 72-10465 Manuel utilisateur

Endress+Hauser

Endress+Hauser Proline Promag 50 Caractéristiques techniques

Siemens

Siemens SITRANS F Coriolis FCT030 Manuel de la liste des pièces

KLINGER

KLINGER CMF V Series Manuel utilisateur

EXFO

EXFO FTB-2 Manuel d'exploitation et d'entretien

Keysight

Keysight M8290A Manuel utilisateur

ADTEK

ADTEK MW-5 Manuel utilisateur