Belkin TSG-UK-1-008 Guide de référence
®Self Help Guide
TSG-UK-1-001 | www.belkin.com | Page 1 of 1
®Self Help Guide
IMPORTANT!
This Guide refers to the
following Products:
Configuring Your Router With Your Modem
Synopsis:
Please read the following carefully;
Requirements:
A standard (Wireless) Router does not come
equipped with the means to connect to the Internet
of it’s own accord but rather is designed to
connect to your existing Modem. Your Modem may
be an ADSL Modem (connected to your phone
line) or a Cable Modem (connected to a co-axial
aerial, often shared with television). Either way the
Modem must have an RJ45 connection to your PC
not a USB connection.
If you have no Modem, or a USB based Modem
then you should ensure you buy a Modem Router
not just a Router.
In order to complete this guide and in so doing
connect to the Internet successfully you will need
the following equipment;
•A working ADSL or Cable Modem (non-Belkin)
•Your Belkin Router or Wireless Router
•2 x RJ45 Ethernet Cables*
•A Computer with an Ethernet (LAN) Port
•Power Supplies for the above Hardware.
•Your Internet Service Provider (ISP) Settings
*A cable should have been provided with your Modem to
connect it to your PC, and another one was provided with
your Belkin Router.
TSG-UK-1-008 | www.belkin.com | Page 1 of 8
All Belkin Routers
®Self Help Guide
TSG-UK-1-001 | www.belkin.com | Page 1 of 1
®
To begin with it is best to start from a known working set-up so this guide assumes
that you currently have Internet working via your Modem directly connected to your
Computer – essentially with the Belkin Router not yet in place.
The Hardware set-up is now complete and all devices can be powered on if they are not
already. The Router’s LEDs should indicate the Modem and PC connections.
Self Help Guide
Configuring Your Router With Your ADSL Or Cable Modem
TSG-UK-1-008 | www.belkin.com | Page 2 of 8
Step 1 – Setting Up The Hardware
Locate the RJ45 Cable between your
Modem and the Networking (LAN) Port of
your Computer. Take note as to the
location of this Port on your Computer as
you will need it again.
Unplug the ‘Modem’ Cable from your
Computer and plug it into the separate
Port on the Rear of the Belkin Router
labelled as ‘Internet/WAN’ or ‘Connection
To Modem’.
Next, locate the RJ45 Cable that was
supplied with your Belkin Router. This is
usually a blue cable.
Plug one end of this Cable into ANY one
of the LAN Ports of your Belkin Router.
These Ports are labelled 1-4.
Connect the other end of the same (blue)
Cable to the Networking Port of your
Computer – the same Port that the
Modem used to be connected to.
®Self Help Guide
TSG-UK-1-001 | www.belkin.com | Page 1 of 1
®Self Help Guide
TSG-UK-1-008 | www.belkin.com | Page 3 of 8
Step 2 - Configuring Your Belkin Router
In most cases there will be no problems connecting between your PC and your Router
now that they are physically connected to one another.
To access the Web User Interface of any Belkin Router simply open your Internet
Browser (i.e. Internet Explorer) and type the default IP Address of the Router into the
Address Bar. This is usually 192.168.2.1. There is no need to add ‘www’ or ‘http://’
All being well the Web User Interface will be displayed and you can login to the Router
by leaving the Password field blank when prompted. As most UK ISPs require Routers
to be configured to use the ‘Dynamic’ Connection Type and this is the Default
Connection Type of all Belkin Routers the Interface may already show that you have an
Internet connection. If the Status Bar of the Router Interface does show ‘Connected’
then the Internet Connection should now be working.
If however the status is displayed in red as ‘No Connection’ even after the Page is
refreshed then further action is required.
With some UK connections simply powering off your Modem for 10 minutes and then
starting it again will allow the Router to be ‘Connected’.
Failing this the Router can always be manually configured by using the Menu option
‘Connection Type’. Under the option for ‘Dynamic’ there is the option to ‘Clone The Mac
Address’. This is required if your ISP has registered the unique MAC Address of your
Computers Network Card as a basis for the connection. ‘Cloning’ the MAC Address
ensures that the Routers unique MAC Address is replaced with that of your Computer
so that connectivity can be resumed.
We would always advise that you check with your ISP as to which settings they
recommend.
®Self Help Guide
TSG-UK-1-001 | www.belkin.com | Page 1 of 1
®
If you are unable to open the Router’s User Interface (192.168.2.1) then the actual
connectivity between PC and Router should be tested. To do this click on the ‘Start’
button, locate the ‘Run’ option and once the ‘Run’ command Window opens type ‘cmd’
into the entry field (as shown below) and then press ‘OK’ or hit ‘ENTER’.
NOTE: ‘cmd’ is simply an abbreviation of ‘command’ which older operating systems
will use instead of the abbreviated form.
A Black DOS-Window should appear with a flashing cursor. Simply type in ‘ipconfig’
and press ‘ENTER’*.
*’ipconfig’ is an abbreviation of Internet Protocol Configuration – For older Operating
Systems use ‘winipcfg’
Self Help Guide
TSG-UK-1-008 | www.belkin.com | Page 4 of 8
Troubleshooting – Unable To Connect To The Belkin Router
®Self Help Guide
TSG-UK-1-001 | www.belkin.com | Page 1 of 1
®
Providing you have a working connection to your Router information similar to that
shown below will be displayed;
By default all Computer Network Interface Cards (NICs) are set to ‘Obtain an IP Address
Automatically’ if the Network Card has done this then it will obtain one from the Router
which is acting as a DHCP Server. The Information shown in the Screenshot above
shows that this is happening correctly;
1. The DNS Suffix shows ‘Belkin’ – This is the ‘Hostname’ of the Belkin Router
2. The Default Gateway shows the Router’s IP Address (192.168.2.1) as used above.
3. The PC has successfully obtained a 192.168.2.x IP-Address from the Router
If you receive that same type of information as shown above then please try connecting
to the User Interface of the Router via your Internet Browser again, as a Network
Connection does seem to be present.
If you receive Information that is missing a ‘DNS Suffix’ and/or ‘Default Gateway’ or
shows any other message including ‘Media Disconnected’ then please double check
the Physical connections and if required continue with the troubleshooting as follows.
Self Help Guide
TSG-UK-1-008 | www.belkin.com | Page 5 of 8
B e l k I n
1 9 2 . 1 6 8 . 2 . 2
2 5 5 . 2 5 5 . 2 5 5 . 0
1 9 2 . 1 6 8 . 2 . 1
®Self Help Guide
TSG-UK-1-001 | www.belkin.com | Page 1 of 1
®
To troubleshoot further click on the ‘Start’ menu and select ‘Control Panel’. In the
‘Control Panel’ double click the icon for ‘Network Connections’ (which in older
Operating Systems may show as ‘Internet Connections’ after which ‘Network’ should
be selected).
Once the Network Connections are open you will see an Icon for your Local Area (LAN)
Connection which is essentially the Network Card of your Computer. This will look
similar to that shown below;
If for any reason there is a red cross shown on the Icon then the physical connection
should be checked.
Self Help Guide
TSG-UK-1-008 | www.belkin.com | Page 6 of 8
®Self Help Guide
TSG-UK-1-001 | www.belkin.com | Page 1 of 1
®
Next, right-click the Icon for your Local Area Connection so that the sub-menu appears
and select ‘Properties’. This will bring up the ‘Properties’ Window for your Computer’s
Network Card.
From the large white window select the option
For ‘Internet Protocol (TCP/IP)’ Providing you
Have administrative rights over the Computer
the ‘Properties’ button should be highlighted.
Self Help Guide
TSG-UK-1-008 | www.belkin.com | Page 7 of 8
Click on the ‘Properties’ button to continue. A
screen similar to that shown left should
appear.
Connectivity problems are often because the
Card has been set to ‘Use The Following IP
Address’ i.e. a Static IP Address.
Set the Card to ‘Obtain An IP Address
Automatically’ and ‘Obtain DNS Server
Address Automatically’ as shown here and
then click the ‘OK’ button to save the
changes.
Once the changes are affected you should
test the connectivity again using ‘ipconfig’ in
the black DOS Window as described before.
®Self Help Guide
TSG-UK-1-001 | www.belkin.com | Page 1 of 1
®
If your attempts to access the Web User Interface of the Belkin Router using the
Router’s Default IP Address (192.168.2.1) result in your Computer attempting to start a
‘Dial-Up Connection’ then please do the following;
•Open the Internet Explorer Browser
•Close any Pop-Up Windows or Error Messages that appear
•Select ‘Tools’ from the Upper Menu Bar of Internet Explorer
•From the ‘Tools’ Menu select the sub-menu item ‘Internet Options’.
A New Window will open displaying the Internet Options organised under different Tab
Headings.
•Select the ‘Connections’ Tab
Here you may see your ISP listed in the large white box. In the centre of this tabbed
page there are also three radio buttons.
•Select the Radio Button ‘Never Dial A Connection’ then click on ‘Apply’ then ‘OK’
You should now re-attempt the connection to the Router’s Web User Interface as
described above.
Self Help Guide
TSG-UK-1-008 | www.belkin.com | Page 8 of 8
Troubleshooting – Internet Browser And Dial-Up Pop-Ups
Table des matières
Autres manuels Belkin Routeur réseau
Belkin
Belkin Wireless G Router Manuel utilisateur
Belkin
Belkin F9K1102V2 Manuel utilisateur
Belkin
Belkin F5D5230-4 Instructions d'installation et d'entretien
Belkin
Belkin N Wireless Manuel utilisateur
Belkin
Belkin F5D9230-4 Manuel utilisateur
Belkin
Belkin F9K1002V4 Manuel utilisateur
Belkin
Belkin F1P1210ENAU Guide de référence
Belkin
Belkin FILTRAGE DE MAC ADRESSE Instructions de montage
Belkin
Belkin High Speed ADSL2+ Manuel utilisateur
Belkin
Belkin RT3200 Manuel utilisateur
Belkin
Belkin N Wireless Manuel utilisateur
Belkin
Belkin F9K1104 Manuel utilisateur
Belkin
Belkin F5D7230au4 Instructions d'utilisation et d'installation
Belkin
Belkin F5D9230-4V4 Manuel utilisateur
Belkin
Belkin F5D8233-4v3 Manuel utilisateur
Belkin
Belkin F5D92304 - Wireless G Plus MIMO Router Manuel utilisateur
Belkin
Belkin F5D7631-4-ETEL Manuel utilisateur
Belkin
Belkin F9K1001V3 Manuel utilisateur
Belkin
Belkin F9K1124 Manuel utilisateur
Belkin
Belkin F5D7233 - Wireless G Travel Router Manuel utilisateur
Manuels Routeur réseau populaires d'autres marques
NETGEAR
NETGEAR FS526T - Switch Manuel utilisateur
Korenix
Korenix JetNet 5710G Series Manuel utilisateur
Automated Logic
Automated Logic ZN551 Manuel du propriétaire
Cisco
Cisco ASR 1000 Series Manuel de l'opérateur
EnGenius
EnGenius ESR-9710 Manuel utilisateur
Cisco
Cisco 805 Series Instructions d'utilisation et de sécurité