Behringer SRC Series Manuel utilisateur

BehringerMods.com

Instructions for modification of Behringer SRC analog inputs and

outputs

The following instructions will cover the details of fully modifying a unit with analog output and

analog input upgrades.

These modifications require a high level of assembly and skill. If you doubt your ability to

complete the mods correctly, please contact BehringerMods to arrange an installation service.

BehringerMods take no responsibility for damage caused to your equipment by modification.

Note: The input upgrade has a fixed gain level. The gain knob ill only adjust the LED meter after upgrade.

The modification package should come with the following parts:

Upgrade PCB for analog Inputs and Outputs

Ribbon cables x2

PCB Stands

peration verview

Remove the equipment cover and keep the screws in a dish.

Disconnect all cables and wires to the main PCB, including ground strap

Remove the main PCB.

Keep the screws in a dish.

Cut the back of pins 2 and 3 on each output XLR.

Use side-cutters. Leave a clear gap.

Solder IDC 2 wires as shown.

Yellow: Left ut XLR -

range: Left ut XLR +

Red: Right ut XLR -

Brown: Right ut XLR +

Solder IDC 2 wires as shown.

Grey: Positive pad of C5 (Right Input XLR +)

Violet: Positive pad of C6 (Right Input XLR -)

Blue: Positive pad of C21 (Left Input XLR +)

Green: Positive pad of C1 (Left Input XLR -)

Black: Top of C118 (Power V-)

White Top of C111 (Power V+)

Solder IDC 1 wires as shown.

Blue: Bottom of R144 (DAC R+)

Green: Bottom of R113 (DAC R-)

Yellow: Bottom of R112 (DAC L+)

range: Bottom of R47 (DAC L-)

Remove resistors R48, R49, R132, R133.

Remove capacitors C70, C71.

Solder IDC 1 wires as shown.

Black: Bottom of R122 (ADC Right -)

White: Top of R24 (ADC Left +)

Grey: Top of R123 (ADC Left-)

Violet: Bottom of R115 (ADC Right +)

Solder IDC 1 wires as shown.

Red: Left utput XLR Pin 1 GND

Brown: Left utput XLR Pin 1 GND

Re-connect all wires and cables.

The upgrades should now be complete.

Read the instructions again and check your work!

(Do not confuse IDC1 and IDC 2).

Ensure there are no wire cuttings or solder in the case, the soldered wires are not touching other parts and solder has

not splashed to the PCBs.

Congratulations and enjoy!

Table des matières

Autres manuels Behringer Équipement d'enregistrement

Behringer

Behringer MIDI FOOT CONTROLLER FCB1010 Mode d’emploi

Behringer

Behringer VIRTUALIZER DSP1000 Manuel utilisateur

Behringer

Behringer ULTRA-CURVE PRO DSP8024 Manuel utilisateur

Behringer

Behringer EX3200 Manuel utilisateur

Behringer

Behringer FEEDBACK DESTROYER PRO FBQ2496 Manuel utilisateur

Behringer

Behringer MiniFBQ FBQ800 Manuel utilisateur

Behringer

Behringer U-CONTROL UMA S UMA25S Manuel utilisateur

Behringer

Behringer DJ CONTROLLER CMD DC-1 Mode d’emploi

Behringer

Behringer V-TONE BASS BDI21 Manuel utilisateur

Behringer

Behringer Noise Reducer NR300 Manuel utilisateur

Behringer

Behringer DI800 Manuel utilisateur

Behringer

Behringer GRAPHIC EQUALIZER EQ700 Manuel utilisateur

Behringer

Behringer SHARK DSP110 Manuel utilisateur

Behringer

Behringer GUITAR LINK UCG102 Manuel utilisateur

Behringer

Behringer U-CONTROL UCA202 Manuel utilisateur

Behringer

Behringer U-PHORIA UMC1820 Manuel utilisateur

Behringer

Behringer ULTRAPATCH PX1000 Manuel utilisateur

Behringer

Behringer Virtual Amplification V-AMP 3 Manuel utilisateur

Behringer

Behringer X-TOUCH ONE Manuel utilisateur

Behringer

Behringer BASS OVERDRIVE BOD400 Manuel utilisateur

Behringer

Behringer POWERLIGHT PL2000 Manuel utilisateur

Behringer

Behringer V-Verb Pro REV2496 Manuel utilisateur

Behringer

Behringer Virtualizer Pro DSP2024P Manuel utilisateur

Behringer

Behringer PB1000 Manuel utilisateur

Manuels Équipement d'enregistrement populaires d'autres marques

KV2 Audio

KV2 Audio 500 Series Manuel utilisateur

Robotics Technologies

Robotics Technologies microBus-Cam II Manuel utilisateur

Seca

Seca 460 Manuel utilisateur

Cognex

Cognex MVS-8000 Series Manuel utilisateur

Mect

Mect MPNC006 Series Manuel utilisateur

Bad Caf

Bad Caf THE LEASH Manuel utilisateur

Strymon

Strymon NIGHTSKY Manuel utilisateur

Mitsubishi Electric

Mitsubishi Electric 16CH DIGITAL RECORDER DX-TL5000U Manuel utilisateur

Tews Technologies

Tews Technologies TPMC465 Manuel utilisateur

Honeywell

Honeywell Excel 50 Manuel utilisateur

SeaLevel

SeaLevel COMM+8.LPCI Manuel utilisateur

Arturia

Arturia AUDIOFUSE STUDIO Manuel utilisateur

Rukra

Rukra RK-1240 Manuel utilisateur

Samson

Samson SCOM Manuel utilisateur

Dynacord

Dynacord DPS260 Manuel utilisateur

Nice

Nice Core Manuel utilisateur

Pyle Pro

Pyle Pro PSS8 Manuel utilisateur

RF-System

RF-System TinyGate Manuel d'utilisation et d'entretien