Behringer CP35 Attenuators Manuel utilisateur

Quick Start Guide

CP35 ATTENUATORS

Legendary Analog Attenuator and

Multiples Module for Eurorack

Controls

(2)

(3)

(4)

(1)

(1) IN and OUT JACKS – A single input connected to the rst

attenuator will pass to all 4 outputs. Additional inputs

will break the chain from the previous input. For example,

input 1 will initially feed all 4 outputs. If you add a signal

to input 2, then input 1 will only feed output 1, and input 2

will feed outputs 2, 3, and 4.

(2) ATTENUATOR KNOBS – Adjust the level of the input

signal passively from -∞ to unity (0 dB).

(3) 6 VOLT OUTPUTS – These outputs give a reference

voltage of -6 Volts on one output pair, and +6 Volts on

the other pair.

(4) MULTIPLES – Connect an input signal to one of the 4-jack

sections, then send up to 3 copies of the same signal to

other devices.

Power Connection

The module comes with the required power cable for connecting

to a standard Eurorack power supply system. Follow these

steps to connect power to the module. It is easier to make these

connections before the module has been mounted into a rack

case.

1. Turn the power supply or rack case power o and

disconnect the power cable.

2. Insert the 16-pin connector on the power cable into the

socket on the power supply or rack case. The connector has

a tab that will align with the gap in the socket, so it cannot

be inserted incorrectly. If the power supply does not have

a keyed socket, be sure to orient pin 1 (-12 V) with the red

stripe on the cable.

3. Insert the 10-pin connector into the socket on the back of

the module. The connector has a tab that will align with the

socket for correct orientation.

4. After both ends of the power cable have been securely

attached, you may mount the module in a case and turn on

the power supply.

Installation

The necessary screws are included with the module for mounting

in a Eurorack case. Connect the power cable before mounting.

Depending on the rack case, there may be a series of xed holes

spaced 2 HP apart along the length of the case, or a track that

allows individual threaded plates to slide along the length of the

case. The free-moving threaded plates allow precise positioning

of the module, but each plate should be positioned in the

approximate relation to the mounting holes in your module

before attaching the screws.

Hold the module against the Eurorack rails so that each of the

mounting holes are aligned with a threaded rail or threaded

plate. Attach the screws part way to start, which will allow small

adjustments to the positioning while you get them all aligned.

After the nal position has been established, tighten the

screws down.

Specications LEGAL DISCLAIMER

Music Tribe accepts no liability for any loss which may be suered by any

person who relies either wholly or in part upon any description, photograph,

or statement contained herein. Technical specications, appearances and

other information are subject to change without notice. All trademarks are the

property of their respective owners. Midas, KlarkTeknik, Lab Gruppen, Lake,

Tannoy,Turbosound, TC Electronic,TC Helicon, Behringer, Bugera, Auratone

and Coolaudio are trademarks or registered trademarks of MusicTribe

LIMITED WARRANTY

For the applicable warranty terms and conditions and additional information

regarding MusicTribe’s Limited Warranty, please see complete details online

at musictribe.com/warranty.

Zhongshan Eurotec Electronics Limited

No. 10 Wanmei Road, South China Modern Chinese Medicine Park,

Nanlang Town, 528451, Zhongshan City, Guangdong Province, China

Controls

Attenuators 4 x passive

rotary attenuators

Signal Input

Type 4 x 3.5 mm jack,

half normalled, DC coupled

Impedance < 25 kΩ, unbalanced

Maximum input level +20 dBu

Signal Output

Type 4 x 3.5 mm jack, DC coupled

Impedance < 25 kΩ, unbalanced

Maximum output level +20 dBu

Multiples

Type 8 x 3.5 mm TS mono jacks,

unbalanced

Arrangement 2 sets of 4

parallel jacks, passive

Compatibility CV and audio signals

6 V Voltage References

Negative 6 V output 2 x 3.5 mm jack, linked

Positive 6 V output 2 x 3.5 mm jack, linked

Impedance 5 kΩ

Power

Power supply Eurorack

Current draw 1 mA (+12 V), 1 mA (-12 V)

Physical

Dimensions 106 x 129 x 35 mm

(4.2 x 5.1 x 1.4")

Rack units 21 HP

Weight 0.18 kg (0.40 lbs)

Autres manuels Behringer Unité de contrôle

Behringer

Behringer 994 MULTIPLES Manuel utilisateur

Behringer

Behringer MIX-SEQUENCER MODULE 1050 Manuel utilisateur

Behringer

Behringer 923 FILTERS Manuel utilisateur

Behringer

Behringer 130 DUAL VCA Manuel utilisateur

Behringer

Behringer 1027 Manuel utilisateur

Behringer

Behringer 992 CONTROL VOLTAGES Manuel utilisateur

Behringer

Behringer MODAMP 2500 Series Manuel utilisateur

Behringer

Behringer 121 DUAL VCF Manuel utilisateur

Behringer

Behringer 2500 Series Manuel utilisateur

Behringer

Behringer 140 DUAL ENVELOPE/ LFO Manuel utilisateur

Behringer

Behringer 2500 Series Manuel utilisateur

Behringer

Behringer 961 Interface Manuel utilisateur

Behringer

Behringer 150 RING MOD/NOISE/S&H/LFO Manuel utilisateur

Behringer

Behringer CP3A-O Manuel utilisateur

Behringer

Behringer 2500 Series Manuel utilisateur

Behringer

Behringer 173 QUAD GATE/MULTIPLES Manuel utilisateur

Behringer

Behringer 112 DUAL VCO Manuel utilisateur

Behringer

Behringer 921A Oscillator Driver Manuel utilisateur

Behringer

Behringer 992 CONTROL VOLTAGES Manuel utilisateur

Behringer

Behringer 902 Manuel utilisateur

Behringer

Behringer BRAINS Manuel utilisateur

Behringer

Behringer 960 SEQUENTIAL CONTROLLER Manuel utilisateur

Behringer

Behringer DUAL ENVELOPE GENERATOR MODULE 1003 Manuel utilisateur

Behringer

Behringer 921B OSCILLATOR Manuel utilisateur

Manuels Unité de contrôle populaires d'autres marques

Festo

Festo Compact Performance CP-FB6-E Manuel de la liste des pièces

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manuel utilisateur

JS Automation

JS Automation MPC3034A Manuel utilisateur

JAUDT

JAUDT SW GII 6406 Series Guide rapide

Spektrum

Spektrum Air Module System Manuel utilisateur

BOC Edwards

BOC Edwards Q Series Manuel utilisateur

KHADAS

KHADAS BT Magic Manuel utilisateur

Etherma

Etherma eNEXHO-IL Manuel utilisateur

PMFoundations

PMFoundations Attenuverter Manuel utilisateur

GEA

GEA VARIVENT Manuel utilisateur

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manuel utilisateur

Altronix

Altronix LINQ8PD Instructions de montage

Eaton

Eaton Powerware Series Manuel utilisateur

WAGO

WAGO 750-407/040-000 Manuel utilisateur

Sony

Sony CCU-590 Manuel utilisateur

Graco

Graco 25D614 Manuel utilisateur

Task Force Tips

Task Force Tips YE-RF-900 Manuel de programmation

Shini

Shini SPV-U Series Manuel utilisateur