BEGA 44 009 Manuel utilisateur

Manuels Éclairage extérieur populaires d'autres marques

Sealey

Sealey LED37 Manuel utilisateur

nordlux

nordlux VEJERS Guide de l'utilisateur

SImx

SImx ELITE LED LHTC637 Manuel utilisateur

GEV

GEV CAROLINE 10833 Manuel utilisateur

NEBO

NEBO NEB-LSP-0020 Manuel utilisateur

WE-EF

WE-EF PFL540 LED Manuel utilisateur

Lindby

Lindby 9949029 Manuel utilisateur

HEPER

HEPER DOGO Side LW6048.585-US Instructions d'installation et d'utilisation

HEPER

HEPER LW8034.003-US Instructions d'installation et d'utilisation

Maretti

Maretti VIBE S 14.6080.04.A Manuel utilisateur

HEPER

HEPER MINIMO Instructions d'installation et d'utilisation

LIGMAN

LIGMAN BAMBOO 3 Manuel utilisateur

Maretti

Maretti TUBE CUBE WALL 14.4998.04 Manuel utilisateur

Maxim Lighting

Maxim Lighting Carriage House VX 40428WGOB Manuel utilisateur

urban ambiance

urban ambiance UQL1273 Manuel utilisateur

TotalPond

TotalPond 52238 Manuel utilisateur

Donner & Blitzen

Donner & Blitzen 0-02661479-2 Manuel utilisateur

LIGMAN

LIGMAN DE-20023 Manuel utilisateur

Installation and Technical Information

BEGA

In the interest of product improvement, BEGA reserves the right to make technical changes without notice.

Replacement Parts

Accessories

Please refer to the appropriate

accessory installation sheet for

further instruction when applicable.

BEGA 1000 Bega Way, Carpinteria, CA 93013 (805)684-0533 Fax (805)566-9474 www.bega-us.com © Copyright BEGA-US 2018

Wall luminaires - stainless steel 44 009

Tools Required:

3mm hex key

Protection Class: IP65

Weight: 2.0 lbs.

Dimensions

A: 2-3/4 “

B: 14-7/8 “

C: 4 “

D: 3 “

Relamping/Maintenance

Carefully unscrew and remove lens with attached

gasket to relamp. Clean luminaire and lens using only

solvent-free cleansers. Replace lens.

Lamp: 1.9W LED

44 009

8/8/2018

Page 1 of 2

Description

Glass with gasket

Driver (120-277V)

LED Module (3000K)

LED Module (4000K)

Part No

11271541

76066

LED-0253/830

LED-0253/840

Notice to Installer for 44 009:

1. For wall applications only.

2. Mounts directly to recessed BEGA 19 538 wiring box (provided) using mounting

plate (provided).

3. In conformance with UL Standard 1598, a silicone based sealant MUST be

used between luminaire and supporting wall.

44 009 - installation:

1. Unscrew and remove glass lens.

2. Feed luminaire wiring through stainless steel mounting plate and into the wiring box.

3. Make supply wiring and luminaire wiring connections inside the wiring box:

MAIN VOLTAGE SUPPLY WIRE TO BLACK LUMINAIRE WIRE

NEUTRAL (COMMON) SUPPLY WIRE TO WHITE LUMINAIRE WIRE

GREEN GROUND WIRE TO GREEN LUMINAIRE WIRE

4. Attach stainless steel mounting plate to 19 538 wiring box. (Figure 1)

5. Attach mounting strap to mounting plate using (2) 8-32 screws (by others).

6. Mount luminaire over mounting strap and tighten set screw at bottom of luminaire.

7. Replace lens.



















Figure 1 (Generic Image)

Small Opening Wiring Box 19 538

Installation and Technical Information

BEGA

In the interest of product improvement, BEGA reserves the right to make technical changes without notice.

BEGA 1000 Bega Way, Carpinteria, CA 93013 (805)684-0533 Fax (805)566-9474 www.bega-us.com © Copyright BEGA-US 2018

Wall luminaires - stainless steel 44 009

44 009

8/8/2018

Page 2 of 2

Product Safety Warnings:

CAUTION - RISK OF FIRE. THIS PRODUCT MUST BE INSTALLED IN ACCORDANCE WITH THE APPLICABLE

INSTALLATION CODE BY A PERSON FAMILIAR WITH THE CONSTRUCTION AND OPERATION OF THE PRODUCT AND

THE HAZARDS INVOLVED. SUITABLE FOR WET LOCATIONS.

MIN 90°C SUPPLY CONDUCTORS.

ATTENTION - RISQUE D’INCENDIE. CE PRODUIT DOIT ÊTRE INSTALLÉ SELON LE CODE D’INSTALLATION PERTINENT,

PAR UNE PERSONNE QUI CONNAÎT BIEN LE PRODUIT ET SON FONCTIONNEMENT AINSI QUE LES RISQUES

INHÉRENTS. CONVIENT AUX EMPLACEMENTS MOUILLÉS.

LES FILS D’ALIMENTATION 90°C MIN.