BEGA 33 539 Manuel

Manuels Éclairage extérieur populaires d'autres marques

Sealey

Sealey LED37 Manuel utilisateur

nordlux

nordlux VEJERS Guide de l'utilisateur

SImx

SImx ELITE LED LHTC637 Manuel utilisateur

GEV

GEV CAROLINE 10833 Manuel utilisateur

NEBO

NEBO NEB-LSP-0020 Manuel utilisateur

WE-EF

WE-EF PFL540 LED Manuel utilisateur

Lindby

Lindby 9949029 Manuel utilisateur

HEPER

HEPER DOGO Side LW6048.585-US Instructions d'installation et d'utilisation

HEPER

HEPER LW8034.003-US Instructions d'installation et d'utilisation

Maretti

Maretti VIBE S 14.6080.04.A Manuel utilisateur

HEPER

HEPER MINIMO Instructions d'installation et d'utilisation

LIGMAN

LIGMAN BAMBOO 3 Manuel utilisateur

Maretti

Maretti TUBE CUBE WALL 14.4998.04 Manuel utilisateur

Maxim Lighting

Maxim Lighting Carriage House VX 40428WGOB Manuel utilisateur

urban ambiance

urban ambiance UQL1273 Manuel utilisateur

TotalPond

TotalPond 52238 Manuel utilisateur

Donner & Blitzen

Donner & Blitzen 0-02661479-2 Manuel utilisateur

LIGMAN

LIGMAN DE-20023 Manuel utilisateur

Installation and Technical Information

BEGA

Accessories

Please refer to the appropriate

accessory installation sheet for

further instruction when applicable.

Replacement Parts

Luminaire Base

Wiring Box

Adapter Plate

Figure 1:

Figure 2:

Set Screws

Surface wall with shielded light source 33 539

Tools Required:

2mm hex key

11/32” Nut driver

Phillips medium screwdriver

Small Flathead screwdriver

Protection Class: IP64

Weight: 1.0 lb.

Dimensions

A: 3 ”

B: 5-1/8 ”

C: 3 1/4 ”

Relamping/Maintenance

Loosen (2) 2mm set screws under luminaire and

remove outer casting with lens. Clean luminaire and

lens using only solvent-free cleansers. Replace lens

and outer casing, making sure that the gasket is

seated properly.

Lamp: 3.2W LED

Description

Lens

Lens gasket

Driver (120-277V) (X1)

LED module (3000K) (X1)

LED module (4000K) (X1)

Part No

140787

831223

75911

LED-0684/830

LED-0684/830

Notice to Installer for 33 539:

1. See page 2 for specic product safety warnings.

2. Mounts directly to a standard single-gang recessed wiring box (by others) using

adaptor plate (supplied).

3. In conformance with UL Standard 1598, a silicone based sealant must be used

between luminaire and supporting wall.

IMPORTANT:

SILICONE RTV MUST BE APPLIED ON BOTH SIDES OF THE ADAPTOR PLATE

TO ENSURE AGAINST WATER INTRUSION.

33 539 - Installation:

1. Using a small athead screwdriver, loosen (2) set screws under luminaire and

remove outer casting with lens. [Figure 1]

2. Feed luminaire wires through luminaire base and adaptor plate wireway hole.

3. Make supply wiring and luminaire wiring connections in the wiring box:

MAIN VOLTAGE SUPPLY WIRE TO BLACK LUMINAIRE WIRE

NEUTRAL (COMMON) SUPPLY WIRE TO WHITE LUMINAIRE WIRE

4. Place a bead of silicone RTV around the outer edge of the back side of the

adaptor plate that will come in contact with the nished wall

(exterior applications only).

5. Attach adaptor plate to single-gang wiring box using (2) wiring box screws.

6. Apply silicone RTV to outside edge of luminaire base and mount luminaire base

to adaptor plate using (2) screws (provided).

IMPORTANT: Note position of orientation arrow on luminaire base and install

accordingly.

7. Replace outer casting and tighten (2) set screws, making sure the gasket is

seated properly.

In the interest of product improvement, BEGA reserves the right to make technical changes without notice.

BEGA 1000 Bega Way, Carpinteria, CA 93013 (805)684-0533 Fax (805)566-9474 www.bega-us.com © Copyright BEGA-US 2019 33 539

07/15/2019

1 of 2

Installation and Technical Information

BEGA Surface wall with shielded light source 33 539

THIS PRODUCT MUST BE INSTALLED IN ACCORDANCE WITH THE APPLICABLE INSTALLATION CODE BY A PERSON

FAMILIAR WITH THE CONSTRUCTION AND OPERATION OF THE PRODUCT AND THE HAZARDS INVOLVED.

SUITABLE FOR WET LOCATIONS.

MIN 90°C SUPPLY CONDUCTORS.

CE PRODUIT DOIT ÊTRE INSTALLÉ SELON LE CODE D’INSTALLATION PERTINENT, PAR UNE PERSONNE QUI CONNAÎT

BIEN LE PRODUIT ET SON FONCTIONNEMENT AINSI QUE LES RISQUES INHÉRENTS.

CONVIENT AUX EMPLACEMENTS MOUILLÉS.

LES FILS D’ALIMENTATION 90°C MIN.

Product Safety Warnings:

In the interest of product improvement, BEGA reserves the right to make technical changes without notice.

BEGA 1000 Bega Way, Carpinteria, CA 93013 (805)684-0533 Fax (805)566-9474 www.bega-us.com © Copyright BEGA-US 2019 33 539

07/15/2019

2 of 2