BC Acoustique EX PHONO-3X Manuel utilisateur
The oponal EX PHONO-3X module is a dedicated
pre-amplifier that will allow you to connect your turntable
to your BC components. The EX PHONO is compable with
MM (Moving Magnet) and MC (Moving Coil) cartridges.
The EX PHONO-3X module is dedicated to be used with
BC Acousque EX products equipped with an « OPTIONAL
BOARD » slot. The board is compable with EX312 - EX322 -
EX332 - EX362 - EX888 - EX322.1 - EX888.1 products.
INSIDE THE PACKAGING
①1x EX PHONO-3X card with its 4 Phillips screws
②1x Large metal plate
-> Fit for amplifiers EX322, EX888 specs
③1x Small metal plate
-> Fit for amplifiers EX332D specs
④1x Stereo RCA cable
⑤1x 6 pin MOLEX cable - Short / POWER
-> For EX332D type amplifiers
⑥1x 6 pin MOLEX cable - Long / POWER
-> For EX322 type amplifiers
⑦1x 3 pin cable / LINE OUT
⑦1x This manual
Tools needed: Philips 2 screwdriver
Phono card MM & MC
WARNING !
Before starng the installaon of the EX PHONO-3X card,
make sure that your amplifier EX Series is powered off AND
disconnected from the wall power cord.
Warning, never operate inside the product if the power
cord is connected. When opened, some internal parts of
the product might cause sever injuries as they are working
at high voltage.
All other internal operaons apart the one described in this
manual about oponal module installaon, must be done
by a qualified technician.
We invite you to contact our accredited service staons if
your product has been chocked, exposed to moisture or
humidity or if any parts has been introduce inside the
product. Internal fuses replacement is also an operaon
which should be done by accredited technician.
IMPORTANT !
PLEASE FOLLOW THESE STEPS IN THE ORDER INDICATED
Important safety instrucons
Introducon
QUICK INSTALLATION GUIDE
2
QUICK INSTALLATION - 8 Steps:
1- Turn off the amplifier (POWER).
2- Remove the power cord from the amplifier.
3- To operate inside the amplifier, unscrew the cabinet or
the dedicated plate witch is
located on the boom of the
product (depending on the
model of your amplifier).
Also remove the metal plate
on the read side.
.
4- Set the source selector (located on the input board) to
acvate the EX PHONO-3X device instead of the
« OPTIONAL » RCA input.
5- Screw the EX PHONO-3X card to the amplifier.
Phono Card With large plate With small plate
((without front plate) for EX322/888 types for EX332D type
Use the "large" plate for EX322 & EX888 amplifiers family
and the "small" plate for EX332D amplifiers family.
6- Connect the power and the signal cords from EX PHONO-
3X card to the pre-amplifier board and the power module.
For EX322:
Make sure the 2
cables will not
be damaged or
crushed by the
cabinet.
For EX332D:
By the trap door
located below the
amplifier, connect
the two cables on
the card dedicated
for this purpose.
For EX888:
Connect the two
cables from your
EX PHONO-3X card:
« LINE OUT » &
« POWER ».
For EX888.1:
Connect the two
cables from your EX
PHONO-3X card:
« LINE OUT » &
« POWER ».
7- Close the amplifier.
8- Connect external cables: HP sources (including your
turntable) and at the end, connect the power cord cable.
For repair, during or aer the warranty, please contact your
dealer.
To obtain warranty service and technical support, thank you
kindly to register your product online on the website
www.bc-acousque.com at the product registraon
secon.
BC ACOUSTIQUE
BP 306
94709 Maisons-Alfort Cedex France
www.bc-acousque.com
Quick installaon guide Installaon
Troubleshoong
EX322D EX322
EX888
EX332D
EX888.1
Autres manuels BC Acoustique Unité de contrôle
Manuels Unité de contrôle populaires d'autres marques
Festo
Festo Compact Performance CP-FB6-E Manuel de la liste des pièces
Elo TouchSystems
Elo TouchSystems DMS-SA19P-EXTME Manuel utilisateur
JS Automation
JS Automation MPC3034A Manuel utilisateur
JAUDT
JAUDT SW GII 6406 Series Guide rapide
Spektrum
Spektrum Air Module System Manuel utilisateur
BOC Edwards
BOC Edwards Q Series Manuel utilisateur
