Base Line Cloud Network BL-CLOUD-WFE Manuel de l'opérateur
1800 362 8774 | hydropoint.com | [email protected]
Cloud Network Module
Installation and Configuration Guide
The Cloud Network Module is available for use
on the BaseStation 1000, the BaseStation 3200,
the FlowStation and the SubStation. It mounts
internally to the top of X-cabinet enclosures and
to the back plate of pedestal enclosures. Power is
supplied by the 5-pin connector, along with any
communication lines that are being used.
The Cloud Network Module provides multiple
communication channels that can be used
by controllers or other devices. The following
channels are currently available for use:
• Cloud Network Ethernet
• Cloud Network Wi-Fi
• Cloud Network Cellular
Materials Provided
• Cloud Network Module
• Antenna with cable
• 5-pin serial cable
• Zip Ties
Tools Needed
• Phillips screwdriver
• Crescent wrench
• Needle nose pliers
We recommend that you back up your current configuration before starting this process in case you
need to restore your system.
• Refer to Backing Up the Controller Programming in the BaseStation 1000 User Manual.
• Refer to Backing Up Your System in the BaseStation 3200 User Manual.
You will also need to halt all watering while you install the Cloud Network Module.
• BaseStation 1000: Press the OFF button.
• BaseStation 3200: Turn the dial to the OFF position.
Please ensure the firmware version of your Baseline controller
meeets the minimum required firmware version to ensure device
compatibility. Minimum required versions are as follows:
• BaseStation 3200 V17.12
• BaseStation 1000 V1.25
• FlowStation V3.5
• SubStation V2.3
2866 294 5847 | baselinesystems.com | [email protected]
BASELINE CLOUD NETWORK MODULE
Cloud Network Module Diagrams 3
Installing the Cloud Network Module into an X/XS cabinet 4-7
Installing the Cloud Network Module into a pedestal cabinet 8-13
Configuration Guide for the BaseSation 3200 14-19
Configruation Guide for the BaseStation 1000, FlowStation & Substation 20-24
Table of Contents
3866 294 5847 | baselinesystems.com | [email protected]
BASELINE CLOUD NETWORK MODULE
Before beginning, familiarize yourself with the parts labeled in the illustrations below.
Two types of communication boards available. The Cloud Network Module wth 4G LTE configuration and the Cloud
Network Module with Wi-Fi configuration.
Cloud Network Module Diagram
A. 5-pin connector for cable to the controller board (Com labeled connector)
B. Connector for the Wi-Fi antenna (not used for cell configuration)
C. Ethernet connector
D. Reset switch and status LED
E. Cell module with antenna cable adaptor
When receiving the Cloud Network Module, inspect the antenna cable on the back of the Cloud Network Module to ensure
that it is securely connected.
Cloud Network Module with 4G Configuration
Cloud Network Module with Wi-Fi Configuration
A. 5-pin connector for cable to the controller board (Com labeled connector)
B. Connector for the WiFi antenna
C. Ethernet connector
D. Reset switch and status LED
E. Connector for the cell module (not used for Wi-Fi configurations)
BL-CLOUD-WFE
BL-CLOUD-LTE
4866 294 5847 | baselinesystems.com | [email protected]
BASELINE CLOUD NETWORK MODULE
Installing the Cloud Network Module into a X/XS Cabinet
For LTE Cloud Network Module installations,
make sure that the antenna is securely
connected before beginning. If the module
is powered up with a loose or disconnected
antenna, damage may occur to the circutry.
This damage is not covered by warranty.
1
Power down the controller.
1. Use needle-nose pliers to remove the
rubber plug from the antenna port on the
top of the cabinet.
2. Remove the nut and the lock washer from
the bottom of the antenna, and then
insert the stem of the antenna into the
port on the top of the cabinet.
2
3
5866 294 5847 | baselinesystems.com | [email protected]
BASELINE CLOUD NETWORK MODULE
From the inside of the cabinet, place the lock
washer on the stem of the antenna, and then
thread the nut onto the stem. Use a wrench
to tighten the nut sufficiently to ensure that
the antenna makes good contact with the
outside of the cabinet.
4
Thread the coax connector that is attached
to the antenna cable onto the stem of the
antenna and hand-tighten it.
5
Installing the Cloud Network Module into an X/XS Cabinet, Cont.
6866 294 5847 | baselinesystems.com | [email protected]
BASELINE CLOUD NETWORK MODULE
Installing the Cloud Network Module into an X/XS Cabinet, Cont.
6
Align the mounting holes on the Cloud
Network Module with the posts on the
cabinet. Use the screws provided to securely
attach the unit inside the cabinet.
7
Plug the 5-pin connector from the Cloud
Network Module into the Comm 2 connector
on the left side of the controller board as
shown.
8
For Wi-Fi installations, attach the cable from
the antenna to the antenna cable port on the
Cloud Network Module as shown.
7866 294 5847 | baselinesystems.com | [email protected]
BASELINE CLOUD NETWORK MODULE
12 Follow the instructions in the Cloud Network Configuration portion of the guide to
complete the setup.
Power-up the controller.
11
Installing the Cloud Network Module into an X/XS Cabinet, Cont.
1. For Cell Modem connections, attach the
cable from the antenna to the antenna
cable port on the Cloud Network Module
as shown.
2. Zip tie the antenna cable through the left
corner hole in the Cloud Network Module.
9
1. For Ethernet connections, attach the cable
to the port on the Cloud Network Module
as shown.
10
8866 294 5847 | baselinesystems.com | [email protected]
BASELINE CLOUD NETWORK MODULE
Installing the Cloud Network Module into a Pedestal Cabinet
1
1. Remove the antenna riser assembly
and the antenna from its packaging.
2. Remove the plastic cap, the nut, and
the lock washer from the stem of the
antenna.
1. Put the stem of the antenna through the
mounting hole on the top of the antenna
riser so the antenna is positioned on top
of the riser.
2. Put the lock washer onto the stem of the
antenna, and then thread the nut onto
the stem. Use a wrench to tighten the nut
sufficiently to ensure that the antenna
makes good contact with the antenna
riser.
2
9866 294 5847 | baselinesystems.com | [email protected]
BASELINE CLOUD NETWORK MODULE
1. Thread the coax connector on the antenna
cable onto the stem of the antenna and
hand-tighten it. Route the antenna cable
towards the bottom of the antenna riser.
2. Insert the tabs on the backing plate into
the holes at the top edge of the riser and
make sure the plate is snug along the back
of the riser
3
Installing the Cloud Network Module into a Pedestal Cabinet, Cont.
1. Open and remove the front door on the
lower part of the pedestal.
2. On the inside left wall of the pedestal,
remove the nuts from the bolts that
secure the cover to the outside wall. Set
the nuts aside to be replaced in a later
step.
3. Remove the bolts that are holding the
cover on the outside wall. Set the bolts
aside to be replaced in a later step.
4. Remove the cover from the outside wall,
making sure that the gasket stays in place.
4
5
1. On the inside left wall of the pedestal,
note the hole that is covered by the
gasket.
2. On the outside left wall of the
pedestal, find the location of the hole
and use a sharp hobby knife to remove
the gasket material that is covering the
hole.
Note: This opening is used to route the
antenna cable inside the pedestal in
order to connect it to the Cloud Network
Module. Make the hole large enough to
pass the cable through, but small enough
to maintain the seal.
10 866 294 5847 | baselinesystems.com | [email protected]
BASELINE CLOUD NETWORK MODULE
6
Align the holes at the bottom of the antenna
riser with the holes in the gasket at the
mounting location on the outside left wall of
the pedestal.
Feed the free end of the antenna cable
through the small hole that you made in the
gasket and into the inside of the pedestal.
2
Working from the outside of the pedestal,
insert the bolts that you removed earlier into
the four holes.
Working from the inside of the pedestal, thread
the nuts that you removed earlier onto the four
bolts. Tighten the nuts snugly.
7
Installing the Cloud Network Module into a Pedestal Cabinet, Cont.
8
Find the orange power connector on the wires
coming from the transformer. Gently pull the
connector away from the board to disconnect
the power.
Ce manuel convient aux modèles suivants
1
Table des matières
Autres manuels Base Line Unité de contrôle
Manuels Unité de contrôle populaires d'autres marques
Festo
Festo Compact Performance CP-FB6-E Manuel de la liste des pièces
Elo TouchSystems
Elo TouchSystems DMS-SA19P-EXTME Manuel utilisateur
JS Automation
JS Automation MPC3034A Manuel utilisateur
JAUDT
JAUDT SW GII 6406 Series Guide rapide
Spektrum
Spektrum Air Module System Manuel utilisateur
BOC Edwards
BOC Edwards Q Series Manuel utilisateur
