Bartec Tech500 Manuel utilisateur

Tech 500 User Guide rev1.0 JUNE 2013

TABLE OF CONTENTS

IMPORTANT NOTICES 2

BEFORE YOU GET STARTED 3

TOOL LAYOUT 4

TOOL CONNECTIONS 5

POWER ON/OFF 6

CHARGING TOOL 7

TOOL DISPLAY AND ICONS 8

MENU SYSTEM

TEST BEFORE YOU TOUCH

RELEARN

REVIEW DATA

TOOLKIT

MY TOOL 11

TOOL POSITIONING/READING A SENSOR 20

UPDATING YOUR TOOL (PC) 29

UPDATING YOUR TOOL (SD Card) 32

UPDATING YOUR TOOL (Wireless)

APPENDIX A: INDUCTIVE CHARGING

APPENDIX B: VIN 37

APPENDIX C: FAQ’S & TROUBLESHOOTING GUIDE 38

APPENDIX D: DEFINITIONS 39

APPENDIX E: TPMS SYSTEM REVIEW 40

APPENDIX F: COMS ERROR TROUBLESHOOTING 42

APPENDIX G: Technical Support 43

LIMITED WARRANTY 44

TOOL REGISTRATION 47

Tech 500 User Guide rev1.0 JUNE 2013

INCLUDED IN Tech500 KIT:

Tech500 TPMS Tool [with protective Boot]

SD Card [in the tool]

Power Supply

Re-Learn Magnet

USB Cable

DB15 to OBDII Cable

Tech500 Quick Start Guide

Tech500 User Guide

Kit CD

IMPORTANT NOTICES

All specifications, illustrations and information contained within this manual are based on the

most current information available at the time of publication. BartecUSA reserves the right to

make changes at any time without obligation to notify any person or organization. BartecUSA

will do its best to keep you the customer informed of any changes that might affect the tools

performance.

FCC Compliance Model: DSW

FCC ID: SX8T500 IC: 5736A-T500

Contains FCC ID: QOQWT12 IC: 5123A-BGTWT12A

Contains FCCID: YOPGS1011MIP IC: 9154A-GS1011MIP

This device complies with Part 15 of the FCC Rules and with Industry Canada

license-exempt RSS standard(s). Operation is subject to the following two

conditions: (1) This device may not cause harmful interference, and (2)

This device must accept any interference received, including

interference that may cause undesired operation.

Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux

appareils radio exempts de licence. L'exploitation est autorisée aux deux

conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2)

Tech 500 User Guide rev1.0 JUNE 2013

l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi,

même si le brouillage est susceptible d'en compromettre le fonctionnement.

Note: Changes or modifications not expressively approved by the party

responsible for compliance could void the user's authority to operate the

equipment.

Note: This equipment has been tested and found to comply with the limits for

a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are

designed to provide reasonable protection against harmful interference when

the equipment is operated in a commercial environment. This equipment

generates, uses, and can radiate radio frequency energy and, if not installed

and used in accordance with the instruction manual, may cause harmful

interference to radio communications. Operation of this equipment in a

residential area is likely to cause harmful interference in which case the user

will be required to correct the interference at their expense.

BEFORE YOU GET STARTED

Before you get started using your Tech500 TPMS tool, there are a few items to review.

Charge your tool

The Tech500 is shipped with a fully charged battery, but due to shelf drain it may require

charging. It is recommended to charge your tool 2+ hours before use. (See page 6 for charging

instructions)

You can register your Bartec

Tech500 @ www.bartecusa.com.

Follow the on-screen prompts filling

in your information and tool serial

Tech 500 User Guide rev1.0 JUNE 2013

number. A valid serial number and supplier is required to process your registration, which can

take up to 24hrs once submitted.

Update your Tool

Once your tool is registered, verify the software level loaded to the level available online and

update your tool if necessary. Refer to section on tool updating for further instruction.

TOOL LAYOUT

TOOL CONNECTIONS

Tech 500 User Guide rev1.0 JUNE 2013

POWER ON/OFF SEQUENCE

The Tech500 is powered up using the ON/OFF key.

On/Off Key

To power the unit on press the On/Off Key for approx 2 seconds –the display will light showing

a logo and software version.

The unit will then display the Main Menu. All data (results and settings) from previous tests is

reloaded.

Tech 500 User Guide rev1.0 JUNE 2013

Power down the Tech500 by using the same ON/ OFF key.

On/Off Key

(Hold, then release when ‘Goodbye’ is displayed.) Auto power off is after 5 minutes of

inactivity.

The unit automatically powers up when the charger or USB port is in use- auto power off is not

operational.

CHARGING TOOL

NOTICE: Only use the power supply or USB cable that is included in the Tech500 tool kit to

charge this tool. The use of un-approved power supplies may damage your tool and will void

the tool warranty.

Tech 500 User Guide rev1.0 JUNE 2013

The Tech500 comes with the rechargeable battery already installed. Battery replacement must

be done at the factory.

For optimum performance, always keep your Tech500 sufficiently charged. It is recommended

that you charge the tool 2 + hours before first use.

The charge port is located on the right side of the tool and is the USB port opening.

TOOL DISPLAY AND ICONS

# of selections

USB indicator

Data stored on tool

Battery indicator

Tech 500 User Guide rev1.0 JUNE 2013

The menu page number (e.g. x/y) on the status line indicates the menu page or item currently

displayed. The first number- x- indicates the item number selected. The second- y- indicates the

total number of items available.

USB Indicator

This status line indicator confirms the Tech500 is connected to the USB port of a computer.

Once communication has been established, results data can be viewed on the pc via the Mass

Storage Device feature. (Use the PC explorer program) “HTM File”

When the USB lead is removed the USB icon will disappear.

Battery Indicator/ Charging

This status line Indicator will illustrate the remaining charge status of the battery.

As different TPM types will ‘use up’ differing amounts of energy, the indicator can only provide

estimates of remaining life left before a recharge is required.

FULL Charge

Partial Charge - charging shortly is

suggested.

Tech 500 User Guide rev1.0 JUNE 2013

Little power in the battery- charging

required.

The battery is FLAT, requires

charging

When the battery is being charged the indicator segments ‘walk;’ from left to right.

When there is an insufficient amount of power remaining in the battery, the Tech500 will flash

its battery icon for two seconds, save all of the TPM Data and then power itself off.

Results Data Available Indicator

Indicates TPM data is available for viewing on the screen (using the View TPM Data command

from the main menu) or via a PC when the Tech500 is in its Mass Storage Device mode. (See

Section on Audit Mode)

Tech 500 User Guide rev1.0 JUNE 2013

When there is no data present, the TPM Data Indicator will not be visible.

To Access the Audit Data, connect your tool to the PC using the supplied USB Cable.

MENU SYSTEM

The Tech500’s menu system provides a hierarchy of instructions and commands. The top line of

the display will always indicate the current menu selected. The home key will always return to

the Main Menu screen- with ‘Select by Vehicle’ highlighted.

Current report

Archived reports

Autres manuels pour Tech500

Table des matières

Autres manuels Bartec Instrument de mesure

Bartec

Bartec MR3000DMS Manuel utilisateur

Bartec

Bartec TECH450PRO Manuel utilisateur

Bartec

Bartec MAK 3003 Manuel utilisateur

Bartec

Bartec RLAnet 17-85G5-2123 Series Fiche technique

Bartec

Bartec Tech1000 Manuel utilisateur

Bartec

Bartec TECH550PRO Manuel utilisateur

Bartec

Bartec ALCAR TECH600 Manuel utilisateur

Bartec

Bartec MAK TIGER 3003 Manuel utilisateur

Bartec

Bartec VOLUTANK Petro 3003 Manuel utilisateur

Bartec

Bartec MAK TIGER 3003 Manuel utilisateur

Bartec

Bartec ComEx Flex Guide de démarrage rapide

Bartec

Bartec TECH600PRO Manuel utilisateur

Bartec

Bartec 07-662 Series Guide de démarrage rapide

Bartec

Bartec TECH400 Manuel utilisateur

Bartec

Bartec RDA01 Manuel utilisateur

Bartec

Bartec TECH 1000 Manuel utilisateur

Bartec

Bartec RDW 03 Manuel utilisateur

Bartec

Bartec HYGROPHIL H 4230-10 A Series Manuel utilisateur

Bartec

Bartec QST 250 Manuel utilisateur

Bartec

Bartec Tech200BT Manuel utilisateur

Bartec

Bartec Syscom MR3000 Series Manuel utilisateur

Bartec

Bartec SYSCOM ROCK Manuel utilisateur

Bartec

Bartec P-600 Manuel utilisateur

Bartec

Bartec ORB P-800LT Manuel utilisateur

Manuels Instrument de mesure populaires d'autres marques

Suaoki

Suaoki D40 Manuel utilisateur

Elster

Elster BK-G1.6 Manuel utilisateur

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manuel

Duratool

Duratool D03128 Manuel utilisateur

Vega

Vega VEGAPULS 65 Manuel utilisateur

Tonghui

Tonghui TH2618B Manuel utilisateur

Tenmars

Tenmars TM-801 Manuel utilisateur

MSR

MSR 145 Manuel utilisateur

TPS

TPS WP-82 Manuel utilisateur

ELMETRON

ELMETRON CP-511 Manuel utilisateur

PCB Piezotronics

PCB Piezotronics 003C30 Manuel utilisateur

Tenma

Tenma 72-10465 Manuel utilisateur

Endress+Hauser

Endress+Hauser Proline Promag 50 Caractéristiques techniques

Siemens

Siemens SITRANS F Coriolis FCT030 Manuel de la liste des pièces

KLINGER

KLINGER CMF V Series Manuel utilisateur

EXFO

EXFO FTB-2 Manuel d'exploitation et d'entretien

Keysight

Keysight M8290A Manuel utilisateur

ADTEK

ADTEK MW-5 Manuel utilisateur