Bartec MAK 3003 Manuel utilisateur

BARTEC BENKE GmbH ● Schulstraße 30 ● D-94239 Gotteszell ● Phone +49 (0) 9929 301-0 ● Fax 301-112

E-Mail: [email protected] ● Internet: www.bartec.de

MAK 3003

Measuring System LYNX

Quick Guide

Software version MAK 3003 2.35

KBA 151021

MAK 3003_LYNX_V.2.35_KBA 151021

Page 2 of 21

Description of the operating unit

Operating keys

The operating keys have a fixed meaning, e.g. scroll up and down, start and

stop pumping, number keys to enter numeric data etc.

Soft keys

Software controlled keys - depending ontherespective operating state, these

keys are activated by the software and will have different functions assigned

to them - this function is shown beside the soft key on the display, e.g. MENU,

SHUT DOWN etc.

Attention

Some soft keys are “hidden” so that they don’t clog up the screen. To activate

a hidden soft key function, press any soft key on the corresponding side of

the screen and the function will be displayed for 3 seconds - e.g. to activate

the EVENTS screen, press any soft key on the left side of the display the

EVENTS function becomes visible and should be pressed within 3 seconds

or else it will vanish again.

Soft keys

Display

Numerical keys

Operating keys

Selection keys

MAK 3003_LYNX_V.2.35_KBA 151021

Page 3 of 21

Home screen

Start-up screen: you will see this screen when the system starts up or after you have

ended a tour.

The system offers so called hidden functions. To display the hidden panel press any of

the four left soft keys. The EVENTS and LAST TOUR functions become visible. Press the

soft key labeled with the desired function within three seconds to enter it. If you do not

press any soft key the hidden panel will disappear automatically.

Hidden soft keys

Visible soft keys

MAK 3003_LYNX_V.2.35_KBA 151021

Page 4 of 21

Events screen

Here you can see the EVENTS screen with two active alarms. Active alarms are indicated

by an exclamation mark under the “A” column.

The “BC-Reader no connection” alarm is still active, but has been marked as

acknowledged by the user. Please observe that the CONFIRM soft key has vanished once

the alarm has been confirmed. If the problem that caused the alarm is fixed, the

acknowledged alarm will be automatically removed from the EVENTS list.

Confirmed alarms are

indicated by a “Y” (for

Yes) under the “Ac”

column (for

Acknowledged).

MAK 3003_LYNX_V.2.35_KBA 151021

Page 5 of 21

Here you can see that the alarms are not active anymore because the problems causing

them have been fixed. They will be displayed in the EVENTS list until they are confirmed

or the system is restarted.

To leave the EVENTS screen you have to activate the hidden panel by pressing any of the

left soft key first. Press EXIT within 3 seconds to return to the home screen.

Alarms have not

been confirmed yet.

Alarms are not active anymore.

MAK 3003_LYNX_V.2.35_KBA 151021

Page 6 of 21

Start a tour

1. Press the soft key labeled with START TOUR on the home screen

2. The Start Tour screen will appear. Before you can start a tour it is necessary to set

the entries displayed on the screen. You can navigate through the entries with the

selection keys at the bottom left of the operating unit. To set an entry press CHANGE

(or any numeric key). Press CONFIRM to start the tour.

MAK 3003_LYNX_V.2.35_KBA 151021

Page 7 of 21

3. You will also need to enter the expected intake volume of this tour. This is important

for sampling calculations.

You can skip this screen (if you do not want tour sampling) by pressing ABORT.

MAK 3003_LYNX_V.2.35_KBA 151021

Page 8 of 21

Start an intake

1. After starting the tour, the Tour Details screen will appear. This screen has hidden

functions on both sides. It may also show already known intakes at the current

location (GPS). If you have already picked up milk at this location, the system will

remember the supplier id and volume and display it for faster operation.

In the picture above you can also see the Tour Details screen with all hidden functions

displayed (left and right).

2. To start an intake at a new location or if no GPS data is available, you have to

activate the hidden panel by pressing any soft key at the right side. Press INTAKE

within three seconds to initialize a new intake.

MAK 3003_LYNX_V.2.35_KBA 151021

Page 9 of 21

You are presented with the Prepare intake screen. Before you can start the intake you

have to enter the Supplier ID and the Expected Volume.

To set an entry, press CHANGE and type in the value with the numeric keys.

Press ENTER and CONFIRM to start the intake.

MAK 3003_LYNX_V.2.35_KBA 151021

Page 10 of 21

3. To start the intake at an already known (GPS) location, just select the desired entry (if

multiple entries are displayed) and press the green START button the system will

start to suck in the milk.

4. The system waits for milk to be sucked in. You can abort the intake by pressing

ABORT as long as no milk has been detected - once milk has been detected, the

ABORT soft key will disappear.

If you press ABORT, you will return to the Tour Details screen. You can restart the intake

again if needed.

Data from a previous

intake at this (GPS)

location.

Autres manuels pour MAK 3003

Table des matières

Autres manuels Bartec Instrument de mesure

Bartec

Bartec MR3000DMS Manuel utilisateur

Bartec

Bartec TECH600PRO Manuel utilisateur

Bartec

Bartec TECH450PRO Manuel utilisateur

Bartec

Bartec Tech200 Manuel utilisateur

Bartec

Bartec ORB P-800LT Manuel utilisateur

Bartec

Bartec HYGROPHIL H 4230-10 A Series Manuel utilisateur

Bartec

Bartec TECH550PRO Manuel utilisateur

Bartec

Bartec MAK TIGER 3003 Manuel utilisateur

Bartec

Bartec Syscom MR3000 Series Manuel utilisateur

Bartec

Bartec Tech1000 Manuel utilisateur

Bartec

Bartec ComEx Flex Guide de démarrage rapide

Bartec

Bartec RDA01 Manuel utilisateur

Bartec

Bartec SYSCOM ROCK Manuel utilisateur

Bartec

Bartec 07-662 Series Guide de démarrage rapide

Bartec

Bartec Tech200BT Manuel utilisateur

Bartec

Bartec TECH400 Manuel utilisateur

Bartec

Bartec MAK TIGER 3003 Manuel utilisateur

Bartec

Bartec Tech500 Manuel utilisateur

Bartec

Bartec RDW 03 Manuel utilisateur

Bartec

Bartec P-600 Manuel utilisateur

Bartec

Bartec TECH 1000 Manuel utilisateur

Bartec

Bartec ALCAR TECH600 Manuel utilisateur

Bartec

Bartec QST 250 Manuel utilisateur

Bartec

Bartec RLAnet 17-85G5-2123 Series Fiche technique

Manuels Instrument de mesure populaires d'autres marques

Suaoki

Suaoki D40 Manuel utilisateur

Elster

Elster BK-G1.6 Manuel utilisateur

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manuel

Duratool

Duratool D03128 Manuel utilisateur

Vega

Vega VEGAPULS 65 Manuel utilisateur

Tonghui

Tonghui TH2618B Manuel utilisateur

Tenmars

Tenmars TM-801 Manuel utilisateur

MSR

MSR 145 Manuel utilisateur

TPS

TPS WP-82 Manuel utilisateur

ELMETRON

ELMETRON CP-511 Manuel utilisateur

PCB Piezotronics

PCB Piezotronics 003C30 Manuel utilisateur

Tenma

Tenma 72-10465 Manuel utilisateur

Endress+Hauser

Endress+Hauser Proline Promag 50 Caractéristiques techniques

Siemens

Siemens SITRANS F Coriolis FCT030 Manuel de la liste des pièces

KLINGER

KLINGER CMF V Series Manuel utilisateur

EXFO

EXFO FTB-2 Manuel d'exploitation et d'entretien

Keysight

Keysight M8290A Manuel utilisateur

ADTEK

ADTEK MW-5 Manuel utilisateur