Baikal Miner Giant Manuel utilisateur
GIANT
Baikal miner
USER
’
S GUIDE
http://www.baikalminer.com
Start Giant
Installation guide
Giant Specifications
Algorithm Hash Rate
Power
(at the wall, with 25℃ambient temp) Power Efficiency
X11
900MH/s±10%
217W±5%
0.25J/MH
X13
900MH/s±10%
255W±5%
0.29J/MH
X14
840MH/s±10%
246W±5%
0.29J/MH
X15
840MH/s±10%
252W±5%
0.3J/MH
Quark
900MH/s±10%
132W±5%
0.15J/MH
Qubit
900MH/s±10%
146W±5%
0.17J/MH
Introduction
Input Power 12V/5A DC
Interface USB
Operation Temp 0 ~ 40 ℃
Dimension 300mm(L) x 123mm(W) x 123mm(H)
Weight 2550g
Package Contents
1 Giant Miner
1 4-pin USB cable
1 dual row 5-pin cable
*Note* 12V DC ATX Power Supply is not pakage contained but required
for the installation.
Connection Guide
1. Select any one of 2 boards and connect it to Orange Pi with 4-pin
USB cable. This board would be called as a master miner from
below, and the other one becomes a slave miner.
2. Connect two boards with a dual row 5-pin cable. OUT port of
master miner and IN port of slave miner should be connected.
3. Plug ATX power to 8-pin PCIe Con of both on each board.
*IMPORTANT* If your power cable has 6-pin connecter, make
sure to plug it as direction followed. Plugging in a wrong position
can cause serious damage to your miner.
<Connection guide for 6-pin power cable>
4. Connect Ethernet port on Orange Pi to Ethernet.
5. Power the ATX power supply on
*Note* Setting Giant miners in daisy-chain
4 Giants at maximum
Only 1 Orange Pi and Ethernet connection are required for
the chain
We recommend using Giants individually.
Example :
Pool setting
1. Enter Giant IP address on your web browser to access pool
setting page and log in with ‘baikal’ as password.
(IP address can be found either on setting page of your internet
router or by using our program from download link)
2. First page you’d see if you log in successfully.
3. Go to Miners tab to set pool lists and give them mining details.
1 – Pool links for your information
2 – Server URLs from each pools
3 – Select Algorithm type
4 – Your wallet address
5 – Pool password (normally set as x)
6 – Give priority with your own numbers; the system counts lowest
number as first and the next as second regardless how big are the
numbers.
*Note*
For P2Pool you should add /+0.08 at the end of your account to
manage the hashrate.
Example)
Keep Giant Up-to-date
Upgrade guide
Configuration
Mode L
Normal mode
Mode H
DFU Boot mode
Firmware Update
01 Before the installation
1. Power off Giant.
2. Remove 5 pin dual row cable connecting two miner boards.
3. Set SW3 to H on both boards.
4. plug 4-pin USB cable to USB Con on any of two boards.
Make sure Giant is off before connecting 4-pin USB cable.
5. Power the selected board on by plugging in 2 of power cables
on the board and check LEDs have lights flow through.
6. Download following list of updating tools available from here :
Name Description
dfu-util.exe USB DFU(Device Firmware Utility) protocol based
flash programming console application.
update_firmware_giant.bat Firmware update batch file.
zadig_2.1.2.exe USB Driver Installer
baikal_giant.bin Firmware binary image.
02 Install DFM Utility driver
1. Connect the other end of 4-pin USB cable to your PC.
2. Check if you have STM Device in DFU Mode on device
manager.
3. Run zadig_2.1.2.exe
4. Select Options>List all devices.
5. Select ‘DFU Util’ on USB device list, then replace driver.
Table des matières
Autres manuels Baikal Miner Matériel informatique
Manuels Matériel informatique populaires d'autres marques
EMC2
EMC2 VNX Series Manuel du propriétaire
Panasonic
Panasonic DV0PM20105 Manuel utilisateur
Mitsubishi Electric
Mitsubishi Electric Q81BD-J61BT11 Manuel utilisateur
Gigabyte
Gigabyte B660M DS3H AX DDR4 Manuel utilisateur
Raidon
Raidon iT2300 Manuel utilisateur
National Instruments
National Instruments PXI-8186 Manuel utilisateur
