Badger Meter Trimble Ranger 3 Manuel utilisateur

Trimble® Ranger 3

ORION® Field Application Software

ORI-PM-00100-EN-03 (May 2015 ) Installation Manual

Trimble® Ranger 3, ORION® Field Application Software

Page ii May 2015ORI-PM-00100-EN-03

CONTENTS

Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Audience and Purpose . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

System Requirements. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

About this Manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Removing Previous Software Versions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

No Previous Software . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Removing Software Using Factory Reset/Clean Boot (Recommended). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Removing Software Using Remove Programs. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Removing Software in Kiosk Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Installing Software. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Transferring Software File from the DVD to a USB Memory Stick. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Installing Software on the Handheld . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Activating Kiosk Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Check COM Port Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Installation Manual

Page iiiMay 2015 ORI-PM-00100-EN-03

Trimble® Ranger 3, ORION® Field Application Software

Page iv May 2015ORI-PM-00100-EN-03

INTRODUCTION

The ORION® Field Application 4.x.x for Trimble® Ranger 3 is a software application designed for automated and manual meter

reading of ORION water and gas endpoints. This manual is the guide for installing the ORION Field Application software on a

Trimble Ranger 3 handheld computer.

Audience and Purpose

Instructions are included for Trimble Ranger 3 handheld users who are installing the ORION Field Application 4.x.x software

for the first time, and for users who are updating to version 4.x.x.

System Requirements

The handheld must meet the system specifications as identified in the most recent version of the ORION Trimble Ranger 3

Product Data Sheet, available at www.badgermeter.com.

The ORION Field Application software requires a Trimble Ranger 3 handheld with a Windows® Mobile 6.5 Professional

operating system to run correctly. The Windows Mobile operating system version number can be found on the About screen

on the handheld. Go to Windows Start> Settings> System> About to access the About screen.

About this Manual

This manual includes step-by-step instructions for installing the ORION Field Application software and includes the following

two main sections:

• Removing Previous Software Versions

• Installing ORION Field Application 4.x.x Software

OTE:N To provide the best solution for our customers, Badger Meter continually improves software programs and

periodically updates this manual to reflect upgrades. Therefore, some discrepancies may be detected between the

installed software and this manual. The software version number on the screen images may differ from the version of

software you are installing.

Typographic Conventions

• Items on the software screens that you will be asked to select or choose by clicking a button, highlighting, checking a

box or another similar means are in bold text and capitalized in the manual.

Example: Tap the View Report button.

• Names of options, boxes, columns, fields and sections are italicized. In most cases, first letters will be capitalized.

Example: The value displays in the Status Information field.

• Messages and special markings are shown in quotation marks.

Examples: “Service Stopped” is shown on the display.

Introduction

Page 5May 2015 ORI-PM-00100-EN-03

REMOVING PREVIOUS SOFTWARE VERSIONS

Before installing the new software, remove all older versions of the software on the handheld.

The Factory Reset/Clean Boot method (1) is recommended. Read the descriptions below and choose the appropriate

procedure based on your handheld setup.

1. Removing the Previous Software Version Using Factory Reset/Clean Boot (Recommended)

Factory reset or "Clean Boot" is the recommended method for removing previous versions of the meter reading

software. This procedure resets the Trimble Ranger to "factory fresh" condition and removes all previously added

software. Refer to "Removing Software Using Factory Reset/Clean Boot (Recommended)" on page 7.

IF YOU ADDED ADDITIONAL SOFTWARE TO THE HANDHELD THAT YOU DO NOT WANT TO REMOVE, SEE THE

ALTERNATIVE METHOD, "REMOVING SOFTWARE USING REMOVE PROGRAMS" ON PAGE 8.

2. Removing the Previous Software Version Using Remove Programs (Alternative)

The Windows tool, "Remove Programs," allows you to select the programs you want to remove. It can be used

when the handheld has other software that you do not want to remove. Refer to "Removing Software Using Remove

Programs" on page 8.

3. (Kiosk mode) Removing the Previous Software Version

For handhelds in Kiosk mode, use procedure 1, "Removing Software Using Factory Reset/Clean Boot (Recommended)" on

page 7, to remove previous Kiosk software and all other previously added software.

If you previously added software to the handheld that you do not want to remove, use the instructions "Removing

Software in Kiosk Mode" on page 11.

No Previous Software

If there is no previous version of the ORION Field Application software on the handheld, go directly to "Installing Software" on

page 14.

Removing Previous Software Versions

Page 6 May 2015ORI-PM-00100-EN-03

Removing Software Using Factory Reset/Clean Boot (Recommended)

IF YOU ADDED ADDITIONAL SOFTWARE TO THE HANDHELD THAT YOU DO NOT WANT TO REMOVE, USE THE

ALTERNATIVE METHOD, "REMOVING SOFTWARE USING REMOVE PROGRAMS" ON PAGE 8.

Power on the handheld and start the factory reset (clean boot).

1. Press and hold the green power key. When the countdown timer starts, release the green power key.

Result: The Power Menu displays (Figure 1).

2. On the Power Menu, tap Reset and immediately PRESS and HOLD both the green power key and the RIGHT key on

the handheld keypad.

Figure 1: Power Menu

Figure 2: Hold power key and RIGHT key at the same time

3. When the Clean Boot screen appears, as shown in Figure 3, release both the green power key and the RIGHT key.

4. Use the up/down navigation arrows on the keypad to

select the Ok button on the Clean Boot screen.

Then press the ENTER key on the keypad to completely

clear the handheld.

OTE:N Tapping does not work on the Clean Boot screen.

Use the keypad.

Result: Several screens display during the next few seconds:

Blank screen, "Scanning...Wait" screen, Windows Embedded

screen, Finalizing screen, blank screen again, and then the

Windows Embedded screen again.

5. Touch the handheld screen to start the reset process as

instructed on the screen.

Figure 3: Clean Boot screen

6. Align the touch screen by tapping the cross hairs. Continue to tap the cross hairs until the screen aligns.

7. At the Password screen, tap Skip.

8. Tap the Complete screen to nish the reset.

OTE:N After performing a factory reset, the handheld date and time need to be reset. Tap Windows Start> Settings>

Clocks & Alarms to set the correct time and date.

The handheld is now ready for the new software installation. Refer to "Installing Software" on page 14.

Press &

hold

Press &

hold

Removing Previous Software Versions

Page 7May 2015 ORI-PM-00100-EN-03

Removing Software Using Remove Programs

Power on the handheld to start the software removal. Use this method if there is additional software on the handheld that

you do not want to remove.

1. At the home screen, tap Windows Start in the lower

left corner.

2. Scroll to nd Settings. Tap Settings.

Figure 4: Settings> System tab

3. Tap System> Remove Programs. You may need to scroll

to nd the icons.

Result: The Remove Programs screen opens.

4. Scroll to nd the Badger Meter software in the list of

programs.

OTE:N The folder name may be different than the one

shown, depending on the software version you

are removing, but should have “Badger Meter,“

“BMI“ or “Badger “ in the name.

5. Tap the le to select it. Then tap the Remove button.

Result: A pop-up window opens to conrm removal as

shown in Figure 7.Figure 5: Remove Programs

Figure 6: Remove Programs screen Figure 7: Confirm program removal

6. Tap Yes to conrm the program removal.

Result: The program le is removed from the list.

Removing Previous Software Versions

Page 8 May 2015ORI-PM-00100-EN-03

7. To complete the removal, tap Windows Start .

8. Scroll to nd File Explorer. Tap File Explorer.

9. Tap in the title bar to show My Device.

Figure 8: My Device

10. Tap My Device> Windows folder> Start Menu folder>

Programs folder.

11. Find the Badger Meter software applications folder as

shown in Figure 10.

OTE:N The folder name may be different than the one

shown, depending on the software version you

are removing.

Figure 9: My Device

12. Tap and hold the Badger Meter software applications folder until a menu displays as shown in Figure 11.

Then tap Delete.

Figure 10: Badger Meter software applications Figure 11: Delete

Removing Previous Software Versions

Page 9May 2015 ORI-PM-00100-EN-03

13. Tap in the title bar to show My Device.

14. Tap to open the Application Data folder.

15. Find the Badger Meter application data folder. In

Figure 13, the folder is labeled BMI_APP_DATA.

OTE:N The folder name may be different, depending on

the software version you are removing. Look for a

folder with“Badger Meter,“ “BMI“ or “Badger“ in

the name.

Figure 12: Application Data folder

16. Tap and hold the Badger Meter application data folder until a menu displays as shown in Figure 14.

Then tap Delete.

Figure 13: BMI App Data folder Figure 14: Delete

Result: All the meter reading software files are removed. The handheld is ready for the new software installation. Refer to

"Installing Software" on page 14.

Removing Previous Software Versions

Page 10 May 2015ORI-PM-00100-EN-03

Autres manuels pour Trimble Ranger 3

Table des matières

Autres manuels Badger Meter Instrument de mesure

Badger Meter

Badger Meter Oval Gear LM OG Series Manuel utilisateur

Badger Meter

Badger Meter Dynasonics UHC100 Manuel utilisateur

Badger Meter

Badger Meter Blancett B220210 Manuel utilisateur

Badger Meter

Badger Meter Oval Gear LM OG-AM Series Manuel utilisateur

Badger Meter

Badger Meter Dynasonics TFX-500w Manuel utilisateur

Badger Meter

Badger Meter Blancett B290-901 Manuel utilisateur

Badger Meter

Badger Meter Blancett B2800 Standard Manuel utilisateur

Badger Meter

Badger Meter 2100R+ Manuel utilisateur

Badger Meter

Badger Meter epm-3 Manuel utilisateur

Badger Meter

Badger Meter IOG Series Manuel utilisateur

Badger Meter

Badger Meter Impeller Data Industrial 3050 Series Manuel utilisateur

Badger Meter

Badger Meter E G2 Series Manuel utilisateur

Badger Meter

Badger Meter Blancett B114-110 Manuel utilisateur

Badger Meter

Badger Meter Hedland PE Manuel utilisateur

Badger Meter

Badger Meter LM OG-TAER Fiche technique

Badger Meter

Badger Meter Vortex VN2000 Manuel utilisateur

Badger Meter

Badger Meter M-series Guide de démarrage rapide

Badger Meter

Badger Meter HR-LCD 4-20 Manuel utilisateur

Badger Meter

Badger Meter Dynasonics Polymer RS-900w Manuel utilisateur

Badger Meter

Badger Meter PRESO COIN Manuel utilisateur

Badger Meter

Badger Meter FC-5000 Manuel utilisateur

Badger Meter

Badger Meter MN Series Manuel

Badger Meter

Badger Meter Recordall RTR Orion 3-Wire Guide d'installation et d'utilisation

Badger Meter

Badger Meter Blancett B3100 Series Manuel de référence

Manuels Instrument de mesure populaires d'autres marques

Suaoki

Suaoki D40 Manuel utilisateur

Elster

Elster BK-G1.6 Manuel utilisateur

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manuel

Duratool

Duratool D03128 Manuel utilisateur

Vega

Vega VEGAPULS 65 Manuel utilisateur

Tonghui

Tonghui TH2618B Manuel utilisateur

Tenmars

Tenmars TM-801 Manuel utilisateur

MSR

MSR 145 Manuel utilisateur

TPS

TPS WP-82 Manuel utilisateur

ELMETRON

ELMETRON CP-511 Manuel utilisateur

PCB Piezotronics

PCB Piezotronics 003C30 Manuel utilisateur

Tenma

Tenma 72-10465 Manuel utilisateur

Endress+Hauser

Endress+Hauser Proline Promag 50 Caractéristiques techniques

Siemens

Siemens SITRANS F Coriolis FCT030 Manuel de la liste des pièces

KLINGER

KLINGER CMF V Series Manuel utilisateur

EXFO

EXFO FTB-2 Manuel d'exploitation et d'entretien

Keysight

Keysight M8290A Manuel utilisateur

ADTEK

ADTEK MW-5 Manuel utilisateur