Badger Meter M-series Guide de démarrage rapide

M-Series® M2000

Connecting a Badger Meter Endpoint to the M2000

Application Brief

IAB-185-01-EN (August 2012)

OVERVIEW

This document describes the connection of a Badger Meter-

supplied endpoint (transmitter), such as an ORION® or GALAXY®

RTR®, or Itron® 100WP or 60WP to an M2000 Mag Meter.

QUICK SETUP FOR TOTALIZER AND FLOW UNIT

M2000 Front Panel Buttons

1. Navigate to Start Menu > Quick Setup > Flow Unit.

2. Select the desired unit of measurement.

3. Navigate to Start Menu > Quick Setup > Totalizer Unit.

4. Select the desired unit of measurement.

PROGRAMMING THE M2000 FOR THE ENDPOINT

Programming for Output #1

1. Navigate to Start Menu >Main Menu > Inputs/Outputs >

Digital Output 1 >Pulses/Unit.

2. Select the desired values.

NOTE: If the Pulse/Unit value is too high, error 110 will display

when you save. The Pulses/Unit and Full Scale Flow

parameters are dependent values that cannot exceed

10 kHz. To correct the error, decrease either or both of the

Pulse/Unit and the Full Scale Flow values.

3. Navigate to Select Function > AMR (50 ms pulse).

4. Press Efour times until the menu text is at Exit This Menu

to exit the programming.

Programming for Output #2

1. Navigate to Start Menu >Main Menu > Inputs/Outputs >

Digital Output 2 >Pulses/Unit.

2. Select the desired values.

3. Navigate to Start Menu >Main Menu > Inputs/Outputs >

Digital Output 1 >Pulses/Width.

4. Set the value to 0050 ms.

5. Press Efour times until the menu text is at Exit This Menu

to exit the programming.

ADDITIONAL NOTES

If the M2000 displays a reading, it will be necessary to either

program the endpoint to match the same reading on the M2000,

or reset the totalizer(s). The M2000 has a separate Unit Multiplier

setting in the Advanced menu that establishes the resolution of the

totalizer reading on the display. This multiplier displays a seven-digit

reading and is set to OFF from the factory. The endpoint must be

programmed to coincide with the value set in the Pulses/Unit and

the Unit Multiplier. For example, if the Unit Multiplier is set to 100

and the Pulse/Unit is set to 0000000.010, the reading on the display

would be 1234500 (the endpoint should be programmed to 12345).

To use the reading from the endpoint in the Reading Data

Management Software, the correct Test Circle Code will also need

to be added in the software. The Test Circle Code will depend on the

Pulses/Unit that was programmed into the M2000.

WIRING AN ORION OR GALAXY RTR ENDPOINT TO

THE M2000

Use either Output #1 or #2 when connecting an endpoint to the

M2000. Output #1 is the recommended option, as an AMR function

exists that will make for easier programming.

To connect the endpoint to Output #1, connect the endpoint wires

this way:

• Terminal 1: Red

• Terminal 2: Black and Green

• Remove jumper JP1 (output #1)

To connect the endpoint to Output #2, connect the endpoint wires

this way:

• Terminal 3: Red

• Terminal 4: Black and Green

• Remove jumper JP2 (output #2)

WIRING AN ITRON 100WP OR 60WP ENDPOINT TO

THE M2000

To connect the endpoint to Output #1, connect the endpoint wires

this way:

• Terminal 1: Red and White

• Terminal 2: Black

• Remove jumper JP1 (output #1)

To connect the endpoint to Output #2, connect the endpoint wires

this way:

• Terminal 3: Red and white

• Terminal 4: Black

• Remove jumper JP2 (output #2)

www.badgermeter.com

M-Series is a registered trademark of Badger Meter, Inc. Other trademarks appearing in this document are the property of their respective entities.

Due to continuous research, product improvements and enhancements, Badger Meter reserves the right to change product or system specications without notice, except to the extent an outstanding

Czech Republic | Badger Meter Czech Republic s.r.o. | Maříkova 2082/26 | 621 00 Brno, Czech Republic | +420-5-41420411

Slovakia | Badger Meter Slovakia s.r.o. | Racianska 109/B | 831 02 Bratislava, Slovakia | +421-2-44 63 83 01

Autres manuels pour M-series

Ce manuel convient aux modèles suivants

Autres manuels Badger Meter Instrument de mesure

Badger Meter

Badger Meter Oval Gear LM OG Series Manuel utilisateur

Badger Meter

Badger Meter 2100 Manuel utilisateur

Badger Meter

Badger Meter Dynasonics UHC100 Manuel utilisateur

Badger Meter

Badger Meter Recordall RTR Orion 3-Wire Guide d'installation et d'utilisation

Badger Meter

Badger Meter Hedland EZ-View Manuel utilisateur

Badger Meter

Badger Meter Blancett B220210 Manuel utilisateur

Badger Meter

Badger Meter E-Series G2 Manuel utilisateur

Badger Meter

Badger Meter Blancett B3100 Series Manuel utilisateur

Badger Meter

Badger Meter epm-3 Manuel utilisateur

Badger Meter

Badger Meter ORION SE Guide d'installation et d'utilisation

Badger Meter

Badger Meter ORION Mobile Read Guide d'installation

Badger Meter

Badger Meter ModMAG M1000 Manuel utilisateur

Badger Meter

Badger Meter FC-5000 Manuel utilisateur

Badger Meter

Badger Meter B131-038 Manuel utilisateur

Badger Meter

Badger Meter M5000 Manuel utilisateur

Badger Meter

Badger Meter iSonic 4000 Manuel utilisateur

Badger Meter

Badger Meter Data Industrial 3000 Series Manuel utilisateur

Badger Meter

Badger Meter ModMAG M2000 Manuel utilisateur

Badger Meter

Badger Meter PortaSonic 9000 Manuel utilisateur

Badger Meter

Badger Meter Magnetoflow Mag Meter Manuel utilisateur

Badger Meter

Badger Meter Blancett B2800XP Manuel utilisateur

Badger Meter

Badger Meter PRESO COIN Manuel utilisateur

Badger Meter

Badger Meter Impeller Data Industrial 228PV Series Manuel utilisateur

Badger Meter

Badger Meter Orion 64989-002 Manuel utilisateur

Manuels Instrument de mesure populaires d'autres marques

Suaoki

Suaoki D40 Manuel utilisateur

Elster

Elster BK-G1.6 Manuel utilisateur

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manuel

Duratool

Duratool D03128 Manuel utilisateur

Vega

Vega VEGAPULS 65 Manuel utilisateur

Tonghui

Tonghui TH2618B Manuel utilisateur

Tenmars

Tenmars TM-801 Manuel utilisateur

MSR

MSR 145 Manuel utilisateur

TPS

TPS WP-82 Manuel utilisateur

ELMETRON

ELMETRON CP-511 Manuel utilisateur

PCB Piezotronics

PCB Piezotronics 003C30 Manuel utilisateur

Tenma

Tenma 72-10465 Manuel utilisateur

Endress+Hauser

Endress+Hauser Proline Promag 50 Caractéristiques techniques

Siemens

Siemens SITRANS F Coriolis FCT030 Manuel de la liste des pièces

KLINGER

KLINGER CMF V Series Manuel utilisateur

EXFO

EXFO FTB-2 Manuel d'exploitation et d'entretien

Keysight

Keysight M8290A Manuel utilisateur

ADTEK

ADTEK MW-5 Manuel utilisateur