Badger Meter ORION Manuel utilisateur

CITY OF PAPILLION

David P. Black, Mayor

Alex Evans, Deputy City Engineer

9909 Portal Road

Papillion, Nebraska 68046

Phone: 402-597-2044

_________ ____________ ____________ ____________ ____________ __________ _______________ ___________________________ ________________ _________ _______________ ___________________________ ______________________ _______________ ___________________________ __________ _______________ ____________ ___________

_________ ____________ ____________ _______________ _________________________ ___________________________ _________________________ ___ ___________________________ ____________ ____________ __________ _______________ ____________________ _____________ _____________ ___________________________ ___________

September 9, 2019

ATTENTION:

The City of Papillion has modified the requirements for residential water meter endpoint installation.

Formerly, a dovetail mounting kit was utilized to mount the water meter endpoint module to an

inside wall or floor joist inside the basement. The new installation method will be to mount the

endpoint module to the exterior of the structure with the included wall cover install kit. There is no

increase to the cost of the meter.

The provided meter package includes 25-ft of cable from the meter register where the endpoint

module can connect (additional extensions available from the Public Works Department upon

request). This cable shall be installed through the structure wall to install the endpoint module on

the outside of the residence. The final positioning of the endpoint module mount on the exterior of

the structure is flexible, but it is required that the mount be placed in a way that it can be accessed by

personnel, at least 1-ft above grade, and near other exterior utility meters and boxes when possible.

This new installation method is effective immediately for single-family residences only. Businesses

and multi-family units are not required to install the endpoint module on the exterior but may

choose to install the endpoint on the exterior to improve access and signal.

All meters now come standard with the wall mount kit. Business or Multi-family units can use this

same kit to install on an interior wall. See attached for the installation manual for the wall mount.

We will also provide this manual with the new meters upon pick-up.

Respectfully Submitted,

Alex Evans, P.E.

Deputy City Engineer

Water Meter Endpoint; Exterior Mount Installation Manual

TWIST TIGHT CONNECTION; DISCONNECT/INSTALL

Twist tight wire disconnection will need to happen in order to run the meter wire to the

exterior for mounting of the meter endpoint.

To install endpoint to the exterior of the property, follow these steps.

1. Carefully open the security cover with a thin blade to access the twist tight connection.

2. Disconnect the twist tight connection and run the wire to the exterior where it will be

reconnected.

3. Reconnect the twist tight connection and cover with the security cover.

Endpoint should look similar to the image below before being mounted to the exterior.

Follow WALL COVER INSTALL KIT for installation of the wall cover.

64394-032 Wall Cover Install Kit

ORI-UM-00025-EN-19

64394032 WALL COVER INSTALL KIT

Wall Cover Install Kit PN: 64394-032 is recommended for proper mounting of an endpoint for indoor and outdoor remote

applications, and is designed to provide an environmentally protected area for gel splice connections (if needed). Outside

dimensions are shown in Figure 9.

For use with: All ORION endpoints

Figure 8: 64394-032 wall cover enclosure

5.80 in.

4.70 in.

.25 in.

2.82 in.

(72 mm)

(119 mm)

(6 mm)

(147 mm)

Figure 9: 64394-032 Outside dimensions

To install an ORION endpoint, follow these steps.

1. Choose an appropriate installation location within the limits of the endpoint cable/connector harness.

2. Verify the proper orientation (Figure 10). The bottom of the enclosure has an opening for IR programming. The

opening gives access to the endpoint IR LED port (Figure 13 and Figure 14) without having to disassemble the unit.

3. Place the endpoint into the wall cover enclosure, antenna

(threaded portion) up.

Cellular LTE-M, LTE endpoints: Figure 10 shows the correct

endpoint placement.

All other ORION endpoints: Make sure the at side of the

endpoint faces in and ts up against the inside wall of the

enclosure.

OTE:N If double-sided tape is included in the kit, you can use

the tape to temporarily secure the endpoint inside the

enclosure before mounting.

4. Position the endpoint cable.

• Route the endpoint cable through the cutout on the

bottom of the wall cover.

Figure 10: ORION Cellular LTE endpoint orientation

OTE:N If you are drilling a hole through the wall behind the enclosure for the endpoint cable, the cable does

not need to route through the cutout at the bottom.

Page 14 February 2019

64394-032 Wall Cover Install Kit

ORI-UM-00025-EN-19

• If the endpoint has an in-line connector, place the connector inside with the

endpoint and route the connector cable through the cutout on the bottom.

OTE:N If used, place gel splice connections inside the enclosure.

OTE:N See "Outdoor Installation for Endpoint with In-line Connector" on

page 16 for additional information about installing the endpoint

outdoors with the wall cover enclosure.

5. Make sure the wall cover is properly positioned, with the endpoint antenna

straight up and the endpoint IR LED port visible through the bottom opening.

6. Secure the wall cover using customer-supplied screws.

Installation is complete. Figure 11: 64394-032 installation complete

67625-001 IR Holder for Wall Cover Install Kit

IR Holder for Wall Cover Install Kit (PN: 67625-001) is an optional part which can be ordered for use with the Wall Cover

install kit (64394-032). The IR holder bracket fits on the wall cover adapter rails to hold an IR programming head in place.

1. Place the optical head of an IR programming cable into the holder. The nubs on the optical head t into the cutouts

on the holder.

(PN: 67625-001) IR holder bracket Optical head of the IR programming cable

Optical head in the bracket

Figure 12: IR holder and programming cable optical head

2. Slide the bracket into the adapter rails at the bottom of the wall cover enclosure (64394-032) so the IR optical head

is aligned with the endpoint LED port. See Figure 13 and Figure 14.

3. Connect the IR programming cable to a Badger Meter mobile reading device to perform IR functions. Refer to the

mobile reading device user manual for IR programming instructions.

Figure 13: IR LED port ORION Cellular LTE endpoint (bottom up view) Figure 14: IR LED port ORION ME endpoint (bottom up view)

Page 15February 2019

Autres manuels pour ORION

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Badger Meter Instrument de mesure

Badger Meter

Badger Meter HR-LCD 4-20 Manuel utilisateur

Badger Meter

Badger Meter ModMAG M1000 Manuel utilisateur

Badger Meter

Badger Meter FC-5000 Manuel utilisateur

Badger Meter

Badger Meter RCM 2000 Manuel utilisateur

Badger Meter

Badger Meter Recordall Turbo Series Manuel utilisateur

Badger Meter

Badger Meter M-series Guide de démarrage rapide

Badger Meter

Badger Meter Blancett B2900 Manuel utilisateur

Badger Meter

Badger Meter Vortex VN2000 Manuel utilisateur

Badger Meter

Badger Meter Oval Gear EPM2-STD Manuel utilisateur

Badger Meter

Badger Meter FC-5000 Manuel utilisateur

Badger Meter

Badger Meter Oval Gear EPM2-STD Manuel utilisateur

Badger Meter

Badger Meter MultySonic 8000 Manuel utilisateur

Badger Meter

Badger Meter Blancett B290-901 Manuel utilisateur

Badger Meter

Badger Meter Blancett B220-880 Manuel utilisateur

Badger Meter

Badger Meter Blancett QuickSert B131C-038 Manuel utilisateur

Badger Meter

Badger Meter FC-5000 Manuel utilisateur

Badger Meter

Badger Meter Dynasonics DXN Series Manuel d'utilisation et d'entretien

Badger Meter

Badger Meter M-series Manuel utilisateur

Badger Meter

Badger Meter F001 Manuel utilisateur

Badger Meter

Badger Meter Hedland EZ-View H915 Manuel utilisateur

Badger Meter

Badger Meter EPM Manuel utilisateur

Badger Meter

Badger Meter 2100R+ Manuel utilisateur

Badger Meter

Badger Meter M5000 Manuel utilisateur

Badger Meter

Badger Meter ModMAG M2000 Mode d'emploi

Manuels Instrument de mesure populaires d'autres marques

Suaoki

Suaoki D40 Manuel utilisateur

Elster

Elster BK-G1.6 Manuel utilisateur

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manuel

Duratool

Duratool D03128 Manuel utilisateur

Vega

Vega VEGAPULS 65 Manuel utilisateur

Tonghui

Tonghui TH2618B Manuel utilisateur

Tenmars

Tenmars TM-801 Manuel utilisateur

MSR

MSR 145 Manuel utilisateur

TPS

TPS WP-82 Manuel utilisateur

ELMETRON

ELMETRON CP-511 Manuel utilisateur

PCB Piezotronics

PCB Piezotronics 003C30 Manuel utilisateur

Tenma

Tenma 72-10465 Manuel utilisateur

Endress+Hauser

Endress+Hauser Proline Promag 50 Caractéristiques techniques

Siemens

Siemens SITRANS F Coriolis FCT030 Manuel de la liste des pièces

KLINGER

KLINGER CMF V Series Manuel utilisateur

EXFO

EXFO FTB-2 Manuel d'exploitation et d'entretien

Keysight

Keysight M8290A Manuel utilisateur

ADTEK

ADTEK MW-5 Manuel utilisateur