Badger Meter ORION SE Guide d'installation et d'utilisation

ORION®

Water Endpoint

Installation Data

ORI-I-79 (11-11)

62014-144 Rev. 2

IMPORTANT:

This manual contains important information.

READ AND KEEP FOR REFERENCE.

ORION® Water Endpoint

Page ii 11-11

Installation Data

CONTENTS

Overview ...................................................................................................................................................................5

Product Unpacking and Inspection ........................................................................................................................5

License Requirements ..............................................................................................................................................5

Identication ............................................................................................................................................................6

Network Endpoint Installation................................................................................................................................7

Splicing Considerations ...........................................................................................................................................7

ORION Installation Kit Part Numbers......................................................................................................................7

Pit Installation...........................................................................................................................................................8

Through the Lid Installation Kit (SE, ME and CE Endpoints) .................................................................................8

Below Lid with Knuckles Installation Kit (ME and CE Endpoints) .........................................................................9

Integrated Pit Lid Hanger Installation Kit (ME and CE Endpoints) .....................................................................10

Vault Installation Kit (ME and CE Endpoints) .......................................................................................................10

Remote Installation................................................................................................................................................11

Remote Wall Mount Box Enclosure Kit (SE, ME and CE Endpoints).....................................................................11

Remote Installation Bracket Kit (SE, ME and CE Endpoints) ...............................................................................14

Wiring a Universal Endpoint..................................................................................................................................17

Universal Endpoint Identication.........................................................................................................................17

Required Splice Tools .............................................................................................................................................17

Wiring the ORION Universal Endpoint to an Encoder..........................................................................................17

Encoder Register Installation ................................................................................................................................19

Page iii

11-11

ORION® Water Endpoint

Page iv 11-11

Installation Data

Overview

This manual contains installation and programming instructions for the ORION® water endpoint.

Proper performance and reliability of ORION endpoints depend upon installation in accordance with these instructions.

Product Unpacking and Inspection

Upon receipt of the product, perform the following unpacking and inspection procedures.

NOTE: If damage to the shipping container is evident upon receipt, request the carrier to be present when the product is

unpacked.

Carefully open the shipping package, follow any instructions that may be marked on the exterior. Remove all cushioning

material surrounding the product and carefully lift the product from the package.

Retain the package and all packing material for possible use in reshipment or storage.

Visually inspect the product and applicable accessories for any physical damage such as scratches, loose or broken parts or

any other sign of damage that may have occurred during shipment.

NOTE: If damage is found, request an inspection by the carrier’s agent within 48 hours of delivery and le a claim with

the carrier. A claim for equipment damage in transit is the sole responsibility of the purchaser.

Carefully remove the pre-wired ORION endpoint and encoder assembly or ORION endpoint from the shipping carton and

inspect for damage. Retain the contents of the installation kit for use in mounting the endpoint in the eld.

License Requirements

This device complies with Part 15 of FCC Rules. Operation of this device is subject to the following conditions: (1) This device

may not cause harmful interference, and (2) this device must accept any interference received, including interference that

may cause undesired operation of the device.

In accordance with FCC Regulations, “Code of Federal Regulations”Title 47, Part 2, Subpart J, Section 1091, transmitters pass

the requirements pertaining to RF radiation exposure. However, to avoid public exposure in excess of limits for general

population (uncontrolled exposure), a 40 centimeter distance between the transmitter and the body of the user must be

maintained during testing.

No FCC license is required by a utility to operate an ORION SE meter reading system.

This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two

conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference

that may cause undesired operation of the device. Le présent appareil est conforme aux CNR d'Industrie Canada applicables

aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil ne doit pas

produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage

est susceptible d'en compromettre le fonctionnement.

IMPORTANT

Transportation: The Federal Aviation Administration prohibits operating endpoints and receivers on all commercial aircraft.

The ORION endpoint is considered an operating transmitter and cannot be shipped by air.

11-11 Page 5

ORION® Water Endpoint

Identication

Each ORION endpoint can be identied using the unique numeric serial number located on a tag attached to the wire harness

and etched on the top (CE) or side (SE, ME) of the endpoint housing. Each Badger Meter encoder is clearly identied on the

face of the register with an assembly number, unit of measure and meter model.

SE/ME Endpoint (Medium Gray) CE RTR® Endpoint (Black) CE ADE® Endpoint (Light Gray)

Recordall® Transmitter

Absolute Digital

Encoder (ADE®)

Figure 1: Endpoints and Encoders

Page 6 11-11

Installation Data

Network Endpoint Installation

When installing an SE or ME (used with a network gateway transceiver) or CE (used with an ORION 4.0 or 2.0 gateway

receiver) endpoint in a pit, the endpoint must be mounted through the lid of a non-metal pit lid for maximum propagation

of the radio signal. If the endpoint is being installed indoors, a wired radio endpoint should be mounted on the outside

of the building or in the oor joist near the outside wall of the building, and away from large metal objects for maximum

propagation of the radio signal.

Splicing Considerations

For non-submerged indoor and outdoor applications where splicing is necessary, splice connections together and wrap any

cables inside the base of the housing.

Splice connections made in pit environments require a pit eld splice kit (62084-001), which can be ordered separately.

Please refer to RTR-I-15 for eld splice kit installation instructions.

ORION endpoints shipped factory pre-wired to a Badger Meter encoder require no splicing. Only the mounting of the

encoder to the meter and tightening the TORX® seal screw is necessary.

For all installations, excess wire should be coiled and cable tied to avoid any damage.

ORION Installation Kit Part Numbers*

TYPE DESCRIPTION ORION SE ORION ME ORION CE

PIT

Through the Lid Installation Kit 64394-024 64394-024 64394-001

Below Lid with Knuckles

Installation Kit 64394-025 64394-003

Integrated Pit Lid Hanger

Installation Kit 64394-026 64394-009

VAULT Vault Installation Kit/Non-Standard

Permalog+® Installation Kit 64394-027 64394-008

REMOTE Remote Wall Mount Box Enclosure Kit 64394-028 64394-028 64394-021

Remote Installation Bracket Kit 64394-029 64394-029 64394-019

*Refer to ORI-P-09 for individual endpoint installation kit components.

11-11 Page 7

ORION® Water Endpoint

Pit Installation

Through the Lid Installation Kit (SE, ME and CE Endpoints)

The Through the Lid Installation Kit is designed for use with a lid with maximum thickness of one-inch, and a standard

hole diameter of 1-7/8 inches.

Figure 2: ORION Pit Endpoint

To install the endpoint through the lid, follow these steps per Figure 2.

1. Screw the nut onto the tube threads as shown.

2. Insert the tube through the bottom of the lid.

3. Screw the top cap onto the tube threads as shown and tighten.

4. Tighten the nut against the bottom of the lid until secure.

If installing an ORION endpoint through a thick lid, you may use a Pit Tube Extender (67025-001) which requires a

two-inch diameter hole. With line of sight, RF performance will be reduced when using this extension.

Pit Lid

Top Cap

Nut

Tube

1" Maximum Pit Lid

Thickness

5.13

Page 8 11-11

Installation Data

Below Lid with Knuckles Installation Kit (ME and CE Endpoints)

For below the lid installations, a special mounting bracket (Figure 3) is available. This mounting support bracket is designed

for use with 3/8", 1/2" and 5/8" rebar or 1/2" schedule 40 PVC pipe.

Figure 3: Pit Support Bracket (Knuckles) - Top View

To install an ORION endpoint below a meter pit lid, follow these steps.

1. Drive rebar or stake into the ground.

Drive rebar or stake into the ground prior to attaching the endpoint to avoid damage.

2. Once in the ground, secure the mounting bracket on the appropriate rebar or pipe using the enclosed washer, wing

nut and hex head bolt provided with the bracket.

3. Insert the endpoint through the bottom of the bracket and thread the lock nut onto the top of the endpoint. For best

results, mount the endpoint a maximum of one to two inches below the underside of the lid.

Figure 4: Pit ORION Beneath Lid Installation

3/8" Rebar

Support Bracket

1/2" Rebar

#6-32 wing nut

#6 washer

#6-32 x 3/4

hex head bolt

Hex head bolt can be placed

in any slot depending upon

the type of support used

1/2" schedule

40 PVC pipe

Meter Pit Lid

Lock Nut

Clamp

ORION

Endpoint

1/2" Schedule

40 PVC pipe

11-11 Page 9

ORION® Water Endpoint

Integrated Pit Lid Hanger Installation Kit (ME and CE Endpoints)

ORION endpoints can also be installed in composite and plastic lids with an integrated hanger for AMR/AMI endpoints. An

installation kit for installing an ORION pit endpoint to the lid is available.

To install an ORION endpoint to a composite or plastic lid, follow these steps.

1. Thread the lock nut onto the top of the ORION endpoint as shown.

2. Slide the endpoint into the lid bracket.

3. Tighten the lock nut so that the endpoint is held rmly in place.

Figure 5: Integrated Pit Lid Hanger Installation

Vault Installation Kit (ME and CE Endpoints)

When installation of the ORION endpoint occurs in a deep vault, Badger Meter oers a kit that can be used to mount the

endpoint to the side of the vault.

To install an ORION endpoint in a deep vault, follow these steps.

1. Mount the C-clamp on the side of the vault. Select a location close to the top of the vault that will not be damaged

when access to the meter is required.

2. Place the neoprene spacer supplied in the installation kit around the endpoint, approximately 1/2 inch from the

top of the endpoint.

3. Thread the locking ring on the endpoint until it makes contact with the neoprene spacer as shown in Figure 6.

4. Insert the endpoint into the C-clamp as shown.

5. Close the C-clamp and lock it in place so that it closes over the neoprene spacer and securely holds the endpoint.

NOTE: ORION radio endpoints perform best with a clear line of sight. Performance varies by installation and lid

construction.

C-Clamp

C-Clamp Around Endpoint

Figure 6: C-Clamp and Placement

Meter Pit Lid Lid Bracket Lid Bracket

ORION Endpoint

Page 10 11-11

Autres manuels pour ORION SE

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Badger Meter Instrument de mesure

Badger Meter

Badger Meter LM-OG-P2 Advanced Manuel utilisateur

Badger Meter

Badger Meter M5000 Manuel utilisateur

Badger Meter

Badger Meter QuikSert Standard Manuel utilisateur

Badger Meter

Badger Meter Dynasonics IS-4000 Manuel utilisateur

Badger Meter

Badger Meter 2100 Manuel utilisateur

Badger Meter

Badger Meter Preso Gemini Cone Manuel utilisateur

Badger Meter

Badger Meter IOG Series Manuel utilisateur

Badger Meter

Badger Meter Blancett 1100 Series Manuel utilisateur

Badger Meter

Badger Meter Blancett B3100 Series Manuel utilisateur

Badger Meter

Badger Meter ER-500 Manuel du propriétaire

Badger Meter

Badger Meter FC-5000 Manuel utilisateur

Badger Meter

Badger Meter ModMAG M-Series M7600 Manuel utilisateur

Badger Meter

Badger Meter ModMAG M2000 Mode d'emploi

Badger Meter

Badger Meter MN Series Manuel

Badger Meter

Badger Meter FC-5000 Manuel utilisateur

Badger Meter

Badger Meter LM-OG-P2 Advanced Manuel utilisateur

Badger Meter

Badger Meter ORION Mobile Read Guide d'installation

Badger Meter

Badger Meter Impeller Data Industrial 3050 Series Manuel utilisateur

Badger Meter

Badger Meter ORION Instructions de montage

Badger Meter

Badger Meter Hedland T303 Manuel utilisateur

Badger Meter

Badger Meter Oval Gear LM OG-AM Series Manuel utilisateur

Badger Meter

Badger Meter ModMAG M1000 Manuel utilisateur

Badger Meter

Badger Meter E Series Manuel utilisateur

Badger Meter

Badger Meter iSonic 4000 Manuel utilisateur

Manuels Instrument de mesure populaires d'autres marques

Suaoki

Suaoki D40 Manuel utilisateur

Elster

Elster BK-G1.6 Manuel utilisateur

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manuel

Duratool

Duratool D03128 Manuel utilisateur

Vega

Vega VEGAPULS 65 Manuel utilisateur

Tonghui

Tonghui TH2618B Manuel utilisateur

Tenmars

Tenmars TM-801 Manuel utilisateur

MSR

MSR 145 Manuel utilisateur

TPS

TPS WP-82 Manuel utilisateur

ELMETRON

ELMETRON CP-511 Manuel utilisateur

PCB Piezotronics

PCB Piezotronics 003C30 Manuel utilisateur

Tenma

Tenma 72-10465 Manuel utilisateur

Endress+Hauser

Endress+Hauser Proline Promag 50 Caractéristiques techniques

Siemens

Siemens SITRANS F Coriolis FCT030 Manuel de la liste des pièces

KLINGER

KLINGER CMF V Series Manuel utilisateur

EXFO

EXFO FTB-2 Manuel d'exploitation et d'entretien

Keysight

Keysight M8290A Manuel utilisateur

ADTEK

ADTEK MW-5 Manuel utilisateur