Bacharach Fyrite Tech 50 Manuel utilisateur

Fyrite®Tech

Model 50 & 60

Combustion Gas Analyzer

Instruction 24-9435

Operation & Maintenance

Rev. 1 – August 2009

Product Leadership • Training • Service • Reliability

ENTER

HOLD

I/O

LIGHT

°C

Fyrite

Analyzer

Tech

WARRANTY

Bacharach, Inc. warrants to Buyer that at the time of delivery this Product will be free from defects in material

and manufacture and will conform substantially to Bacharach Inc.’s applicable speciﬁcations. Bacharach’s

liability and Buyer’s remedy under this warranty are limited to the repair or replacement, at Bacharach’s option,

of this Product or parts thereof returned to Seller at the factory of manufacture and shown to Bacharach Inc.’s

reasonable satisfaction to have been defective; provided that written notice of the defect shall have been given

by Buyer to Bacharach Inc. within two (2) years after the date of delivery of this Product by Bacharach, Inc.

Bacharach, Inc. warrants to Buyer that it will convey good title to this Product. Bacharach’s liability and Buyer’s

remedy under this warranty of title are limited to the removal of any title defects or, at the election of Bacharach,

to the replacement of this Product or parts thereof that are defective in title.

THE FOREGOING WARRANTIES ARE EXCLUSIVE AND ARE GIVEN AND ACCEPTED IN LIEU OF (I) ANY

AND ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING WITHOUT LIMITATION THE IM-

PLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE: AND (II) ANY

OBLIGATION, LIABILITY, RIGHT, CLAIM OR REMEDY IN CONTRACT OR TORT, WHETHER OR NOT ARIS-

ING FROM BACHARACH’S NEGLIGENCE, ACTUAL OR IMPLIED. The remedies of the Buyer shall be limited

to those provided herein to the exclusion of any and all other remedies including, without limitation incidental or

consequential damages. No agreement varying or extending the foregoing warranties, remedies or this limita-

tion will be binding upon Bacharach, Inc. unless in writing, signed by a duly authorized ofﬁcer of Bacharach.

AInstruction 24-9435

www.mybacharach.com

Notice:

Product improvements and enhancements are continuous, therefore the speciﬁcations and information con-

tained in this document may change without notice.

Bacharach, Inc. shall not be liable for errors contained herein or for incidental or consequential damages in con-

nection with the furnishing, performance, or use of this material.

No part of this document may be photocopied, reproduced, or translated to another language without the prior

written consent of Bacharach, Inc.

BACHARACH and Fyrite are registered trademarks of Bacharach, Inc. All other trademarks,

trade names, service marks and logos referenced herein belong to their respective companies.

Declaration of Conformity

Manufacturer’s name: Bacharach, Inc.

Manufacturer’ address: 621 Hunt Valley Circle

New Kensington, PA 15068

Product name: Fyrite Tech

conforms to the following speciﬁcations:

European Directive 89/336/EEC

EN50082-1: 1997 (Electrostatic Discharge)

EN50082-1: 1997 (Immunity)

EN55022; Group 1, Class B (Emmission)

Fyrite Tech

Instruction 24-9435 i

Contents

1.0 INTRODUCTION .................................................... . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

1.1 The Fyrite Tech . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

1.2 Operation Overview .... . .... . .... . ..... . .... . .... . ..... . .... . ..... ...... . ..... ..... . .... . ... 2

2.0 TECHNICAL CHARACTERISTICS...................................................3

3.0 SETTING UP THE ANALYZER ......................................................... 5

3.1 Scope ................................................................................................. 5

3.2 Checking & Replacing the Batteries. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

3.3 Connecting the Probe. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

3.4 Front Panel Pushbuttons. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

3.5 Setup Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

3.5.1 Entering Setup ......................................................................9

3.5.2 Selecting Temperature Units................................................9

3.5.3 CO Channel Setup (Model 60 only) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

3.5.4 Exiting the Setup Mode ......................................................10

4.0 OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

4.1 Starting a Combustion Test. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

4.1.1 Analyzer Turn On and Warm Up. . . . . . . . . . ............................. 11

4.1.2 Selecting a Fuel ........................ . . . . . . . . ................................... 11

4.1.3 Manual Zero of the CO Channel (Model 60 only) . . . . . . . . . . . . . . 11

4.1.4 Sampling Point . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .............................12

4.1.5 Performing a Combustion Efﬁciency Test. . . . . . . . . . . . . . . . . . . . . . . . . . 14

4.1.6 Ending a Combustion Test. . . . . . . . . . . . . . . . . . . . . . ............................14

4.1.7 Turning OFF the Analyzer ................................................. 14

4.2 Warm-Up Screens .......................................................................... 15

4.3 Fuel Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

4.4 TA Screen ....................................................................................... 16

4.5 CO2 & O2 Screen ...........................................................................16

4.6 CO & Air Free Screen (Model 60 only). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

4.7 TL & ETa Screen. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

4.8 qA & Excess Air Screen ................................................................. 18

4.9 COC2 Screen (Model 60 only). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

4.10 Stack & EFF Screen. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

4.11 Sensor Error Screen. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

4.12 Resetting the Microprocessor ......................................................20

4.13 Run Mode Screens. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

Fyrite Tech

Instruction 24-9435

5.0 CALIBRATION & MAINTENANCE ................................................ 21

5.1 Entering the Calibration Mode and Testing the Display Seg-

ments .....................................................................................................21

5.2 Ambient Temperature Calibration. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

5.3 TA (Stack Temperature) Thermocouple Channel Calibration. . . . 22

5.4 Oxygen Sensor Zero ......................................................................23

5.5 CO Sensor Zero & Calibration (Model 60 only) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

5.6 Particulate Filter Replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

5.7 Water Trap / Filter Maintenance .... . ...... . ..... . ...... ...... . ..... . ...... . ..... . 27

5.8 O2 Sensor Replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

5.9 CO Sensor Replacement (Model 60 only). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

5.10 Pump Assembly Replacement ..................................................... 32

6.0 PARTS & SERVICE. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

6.1 Replacement Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

6.2 Accessories. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

6.3 Service Centers. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34

Appendix A - Formulas and Tables ....................................................... 35

Fyrite Tech

Instruction 24-9435 iii

Model No.

Part No.

Fyrite Tech 50

24-7233P

Fyrite Tech 60

24-7234P

Measurements:

Oxygen

Stack Temperature

Ambient Temperature

Carbon Monoxide

Calculations:

Stack Loss (qA)

Efﬁciency & ETa

Excess Air (Lambda)

Carbon Dioxide

CO air free

Ratio of CO/CO2

Accessories:

4 ‘AA’ Batteries

Instruction Manual

Probe & Hose Assembly

Quick Reference Guide

Ordering Information

Fyrite Tech

Instruction 24-9435

Notes:

Instruction 24-9435 1

Fyrite Tech

1.0 INTRODUCTION

1.1 The Fyrite Tech

Available in two models, the Fyrite Tech 50 and 60 are hand-held ana -

lyze r s that are designed to calculate the efﬁ c i ency of resi d ential furnaces

and combustion appliances by measuring the stack temperature and the

percent oxygen level in the ﬂ u e-gas stream.

While both analyzers are cap a b l e of combust i on testing, the Fyrite Tech

60 has the added capability of meas u ring CO, calculating CO air-free, and

calculating the ratio of CO/CO2.

Fyrite Tech 50 Fyrite Tech 60

Measures: Measures:

• Oxygen (O2)• Oxygen (O2)

• Stack Temperature (TA) • Stack temperature (TA)

• Ambient Temperature (TL) • Ambient Temperature (TL)

• Carbon Monoxide (CO)

Calculates: Calculates:

• Stack Loss (qA) • Stack Loss (qA)

• Efﬁ c iency & ETa • Efﬁ c iency & ETa

• Carbon Dioxide (CO2) • Carbon Dioxide (CO2)

• Excess Air (Lambda) • Excess Air (Lambda)

• CO air-free

• Ratio of CO/CO2

WARNINGS!

This analyzer is not intended to be used on a continuous

basis.

The analyzer does not have an audible alarm, and is not

intended to be used as a safety device.

Except for battery replacement, this analyzer should only be

opened and serviced by authorized personnel.

When testing an appliance, a full visual ins p ection of the ap-

pliance should be carried out to ensure its safe ope r a t ion.

Instruction 24-9435

Fyrite Tech

1.2 Operation Overview

Pressing the I/O button turns the analyzer ON and OFF. Note that there is

a 60 second warm-up period and a 5 second delay before the analyzer turns

OFF, during which time the unit can be kept ON by pressing the ENTER

button.

After warm-up is complete, choose the fuel code that corresponds to the

fuel being burned by the appliance being tested; then press the ENTER

button to place the analyzer into its Run Mode and begin the combustion

testing process.

Begin testing by inserting the analyzer’s probe tube into the ﬂug-gas

stream of the appliance under test. Each analyzer model will continuously

monitor the ﬂue gas and display measured and calculated values that

are relative to the combustion process. These values are displayed on the

analyzer’s LCD, and are chosen for display by pressing the Inc r ement (▲)

and Decrement (▼)buttons.

Pressing the HOLD button during a test will freeze all measured and

calculated combustion parameters at their current values. Pressing the

ENTER button resumes testing.

A backlight enables an operator to read the display in dimly-lit areas.

Pressing the LIGHT button turns the backlight ON and OFF. The backlight

will automatically turn OFF after 10 minutes of keyboard inactivity.

A power saver function will shut the analyzer OFF after 20 minutes of

keyboard inactivity. The power saver function, however, is disabled if the

detected O2value is less than 17.9% or the CO value is more than 50 ppm.

Instruction 24-9435 3

Fyrite Tech

2.0 TECHNICAL CHARACTERISTICS

The Analyzer Directly Measures and Displays:

• Flue Gas O2content ..................................... 0.0 to 20.9% O2

• Stack Temperature. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –18 to 537 °C (0 to 999 °F)

• Ambient Temperature. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0 to 40 °C (32 to 104 °F)

• Flue Gas CO content (Model 60) ................. 0 to 2000 ppm CO

The Analyzer Computes and Displays:

(when the measured oxygen level is below 17.9 %)

• ETa ............................................................... 0 to 99%

• Stack Loss (qA). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.0 to 100.0%

• Efﬁ c iency (EFF). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.1 to 99.9%

• Flue Gas CO2content. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.0 to a fuel dependent

maximum value in %

• Excess Air (Lambda).................................... 0 to 9.55

• Flue Gas CO air-free content (Model 60)..... 0 to 9999 ppm

• Ratio of CO/CO2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0 to 0.9999

Fuel Selection:

(F1 thru F4 denotes the fuel selected as displayed on the LCD)

• Natural Gas (F1)

• LPG (F2)

• Light Oil (F3)

• City Gas (F4)

Normal Operating Conditions:

Temperature:

• Analyzer ....................................................... 0 to 40 °C (32 to 104 °F)

• Probe. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 538 °C max. (1,000 °F) at

127 mm insertion

Humidity. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 to 90% RH,

Non-Condensing

Instruction 24-9435

Fyrite Tech

Power Requirements .................................... Four ‘AA’ Alkaline batteries

Operating Time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 hours cont i nuo u s (pump

runn i ng and backlight off)

Warm Up Time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60 seconds

Display........................................................4 Digit, 2 Line, 7-segment

L i quid Crystal Disp l ay

Front Panel Controls .............................. Six pushbutton switches

(Refer to Section 3.4)

Accuracy:

•Oxygen....................................................±0.3% O2w/typical ﬂue gas

concentration of CO2

•Carbon Monoxide (Model 60) ................ ±5% of reading or ±10 ppm,

whichever is greater*

•Stack Temperature ................................ ±2 °C between 0 & 124 °C

(±4 °F between 32 & 255 °F)

±3 °C between 125 & 249 °C

(±6 °F between 256 & 480 °F)

±4 °C between 250 & 400 °C

(±8 °F between 481 & 752 °F)

Agency Approval . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . CE Mark

* Tighter CO accuracy in the lower ranges, up to ±2 ppm, may be attained

if a lower range calibration gas (e.g. 100 ppm CO) is used.

Autres manuels pour Fyrite Tech 50

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Bacharach Instrument de mesure

Bacharach

Bacharach 3015-4286 Manuel

Bacharach

Bacharach 100 Guide de dépannage

Bacharach

Bacharach Neutronics Mini-ICS Manuel utilisateur

Bacharach

Bacharach Leakator Jr. Manuel utilisateur

Bacharach

Bacharach LS-20B Manuel utilisateur

Bacharach

Bacharach PCA 2 Manuel de la liste des pièces

Bacharach

Bacharach 0024-8555 Manuel utilisateur

Bacharach

Bacharach Draftrite Manuel utilisateur

Bacharach

Bacharach SF6 Portable Monitor Manuel utilisateur

Bacharach

Bacharach Fyrite INSIGHT PLUS Manuel utilisateur

Bacharach

Bacharach Fyrite INTECH Manuel utilisateur

Bacharach

Bacharach 2810 Guide de dépannage

Bacharach

Bacharach Tru Pointe Manuel d'utilisation

Bacharach

Bacharach AGM-MZ Manuel utilisateur

Bacharach

Bacharach QV2 Manuel

Bacharach

Bacharach Neutronics 5100E Manuel utilisateur

Bacharach

Bacharach Snifit 40 Manuel utilisateur

Bacharach

Bacharach AGM300 Manuel utilisateur

Bacharach

Bacharach Fyrite INSIGHT PLUS Manuel utilisateur

Bacharach

Bacharach Monoxor Plus Manuel utilisateur

Bacharach

Bacharach CO2 Analyzer 3150 Mode d’emploi

Bacharach

Bacharach 0012-9015 Manuel utilisateur

Bacharach

Bacharach PCA 400 Manuel utilisateur

Bacharach

Bacharach MONOXOR XR Manuel utilisateur

Manuels Instrument de mesure populaires d'autres marques

Suaoki

Suaoki D40 Manuel utilisateur

Elster

Elster BK-G1.6 Manuel utilisateur

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manuel

Duratool

Duratool D03128 Manuel utilisateur

Vega

Vega VEGAPULS 65 Manuel utilisateur

Tonghui

Tonghui TH2618B Manuel utilisateur

Tenmars

Tenmars TM-801 Manuel utilisateur

MSR

MSR 145 Manuel utilisateur

TPS

TPS WP-82 Manuel utilisateur

ELMETRON

ELMETRON CP-511 Manuel utilisateur

PCB Piezotronics

PCB Piezotronics 003C30 Manuel utilisateur

Tenma

Tenma 72-10465 Manuel utilisateur

Endress+Hauser

Endress+Hauser Proline Promag 50 Caractéristiques techniques

Siemens

Siemens SITRANS F Coriolis FCT030 Manuel de la liste des pièces

KLINGER

KLINGER CMF V Series Manuel utilisateur

EXFO

EXFO FTB-2 Manuel d'exploitation et d'entretien

Keysight

Keysight M8290A Manuel utilisateur

ADTEK

ADTEK MW-5 Manuel utilisateur