B-TEK Scales DuraShield Manuel utilisateur

Instruction

Manual

DuraShield

Bench Scales

3/15/23

V2023.1

B-TEK DuraShield Series Bench Scale Instruction Manual

- 2 -

Table of Contents

1. Safety First…………………………………………………………………………………. 3

2. Introduction………………………………………………………………………………… 4

3. Specifications……………………………………………………………………………… 5

4. DuraShield Bench Scale Assembly…………………………….……………………….6-8

5. Indicator Installation………………………………………………………………………..9

6. Load Cell Replacement………………………………………….………………………..10

7. Exploded View……………………………………………………………………………. 11

8. Replacement Part Numbers……………………………………………………………...12

9. B-TEK Contact Information………………………………………………………………..13

B-TEK DuraShield Series Bench Scale Instruction Manual

- 3 -

Safety First

Please call a B-TEK-authorized service provider for service or repairs.

•Ensure that the area used for this equipment is safe for this equipment.

•Allow only qualified personnel to work on electric/electronic components.

•Do not use this equipment for anything other than its intended use.

•Ensure equipment is plugged into stable power sources.

•Keep equipment away from high voltage, vibration, and high draft areas.

•Keep equipment cords and cables secured and protected.

•Perform periodic inspections to keep equipment in good working order.

•Never apply a load over the capacity of your scale.

•Keep the area around your scale free of debris.

SAFETY WARNING

Always unplug or remove power source from equipment before cleaning with water

unless it has been installed by professionals that determine otherwise.

After cleaning is done always ensure equipment is completely dry before returning to

or plugging into power source unless it has been installed by professionals that determine

otherwise.

B-TEK DuraShield Series Bench Scale Instruction Manual

- 4 -

Introduction

The information provided in this manual is a guide to installing the B-TEK, LLC. DuraShield

series single-point bench scale. This document is intended as a guide only, and the actual

installation should be performed by qualified personnel only.

All sales of goods are subject to the standard warranty and the standard terms and conditions

published by B-TEK, LLC.

Should you have any questions regarding the DuraShield series single-point bench scale,

contact your local B-TEK, LLC. scale representative.

oAvailable in 12” X 12” and 18” X 18” sizes.

oThe DuraShield bench scale has a hardened powder coated surface that will

provide years of protection.

oAvailable in 50lb/25kg, 100lb/50kg, 200lb/100kg and capacities.

oStructure powder coated carbon steel.

oSingle point aluminum load cell.

B-TEK DuraShield Bench Scale Shown with BWS Indicator.

Indicator

B-TEK DuraShield Series Bench Scale Instruction Manual

- 5 -

Specifications

MODEL

DuraShield 12”x12”

DuraShield 18”x18”

Capacities

50lb/25kg,

100lb/50kg,

200lb/100kg

50lb/25kg,

100lb/50kg,

200lb/100kg

Readability

.01lb/.005kg,

.02lb/.01kg,

.05lb/.02kg

.01lb/.005kg,

.02lb/.01kg,

.05lb/.02kg

Max. Divisions

5000e

Weighing Units

lb, kg

Platter sizes

12” x 12”, 18” x 18”

Construction

Powder Coated Carbon Steel

Load Cell Operating

Temperature

14°F - 104°F / -10°C - + 40°C

Weight Base

15.5lbs.

44.5lbs.

Weight Indicator

Works with industry-standard indicators

DIMENSIONS

12.0 inches

18.0 inches

12.0 inches

18.0 inches

3.75 -4.25

4.0 –4.5 in.

B-TEK DuraShield Series Bench Scale Instruction Manual

- 6 -

Assembly

Unpacking

Carefully remove the bench scale from its box, ensure that it is not damaged, and all

parts are included.

•Bench scale with load cell and spider assembly.

•Column (Optional)

•Platter

Installing the Column

Assemble the bench scale and the column by inserting bolts spacers as shown in image

below. Put lock washers and nuts on the bolts and tighten until lock washer snaps in its

lock position.

Spacers

Bolts

B-TEK DuraShield Series Bench Scale Instruction Manual

- 7 -

After fastening the column to the base install all the bench scale and column leveling

feet as shown in the image below.

Place the bench scale on an environmentally sound level surface and adjust the feet on

the bench base only.

(Do not adjust the column feet at this point) until the bullseye level shows that it is

level as shown in the image below. Once the scale is positioned and level adjust the

column feet until they sit firm to the surface (It is important to make sure that the

column feet are taking the pressure off the column only). Finally, tighten all lock

nuts.

Leveling Foot

Leveling Foot Lock Nut

B-TEK DuraShield Series Bench Scale Instruction Manual

- 8 -

Bullseye Level Adjusting

Overload Stop

The overload stop is a set crew placed on the underside of the base and is designed so

that the load cell bottoms out when more weight is applied than the scales capacity. To

adjust this screw simply apply the weight that matches the capacity of the scale plus 5%

and adjust the screw in until it hits the cell. The overload stop is now set to stop at

anything over 105% of the scale’s capacity. Use blue Loctite when setting screw.

Unlevel

Level

Overload Screw

B-TEK DuraShield Series Bench Scale Instruction Manual

- 9 -

Indicator Installation

Mount the indicator on the column mounting bracket. Tighten the wing nuts to secure

the indicator to the column.

Terminate the load cell wires to the load cell terminal located on the main board of the

indicator. Reference the indicator manual that is being connected to the DuraShield

bench scale for load cell termination points.

See the diagram below for load cell wire color code.

Calibrate the scale using certified calibration weights and to the scale’s capacity when

possible.

After calibrating the scale, test it at the low end, middle and high end to insure it is

working properly. Once the scale is confirmed working, the scale is now ready for use.

B-TEK BT-ASP-1 Load

Cell

+ Input

RED

- Input

BLACK

+ Sense

BLUE

- Sense

BROWN

+ Output

GREEN

- Output

WHITE

Shield

CLEAR

B-TEK DuraShield Series Bench Scale Instruction Manual

- 10 -

Load Cell Replacement

Install the load cell using supplied B-TEK ASP-1 load cell and shims. Torque the B-TEK

ASP-1 load cells to 76 in. lbs.

Spider assembly to

load cell mounting

bolts.

Bullseye bubble level

glued in this position.

using only Loctite 401

Spider assembly to

Platter leveling Feet.

Lower base load cell

mounting bolts.

Table des matières

Autres manuels B-TEK Scales Échelle

B-TEK Scales

B-TEK Scales WorldWEIGH C200 Series Manuel utilisateur

B-TEK Scales

B-TEK Scales BT-BC Manuel utilisateur

B-TEK Scales

B-TEK Scales WorldWEIGH C100 Series Manuel utilisateur

B-TEK Scales

B-TEK Scales Skynet Instructions d'installation et d'entretien

B-TEK Scales

B-TEK Scales 4 Square Manuel utilisateur

B-TEK Scales

B-TEK Scales DD1010 Manuel utilisateur

B-TEK Scales

B-TEK Scales TensionLink WS Manuel utilisateur

B-TEK Scales

B-TEK Scales Above-ground Manuel utilisateur

B-TEK Scales

B-TEK Scales AX200 Manuel utilisateur

B-TEK Scales

B-TEK Scales Centurion-DT Manuel utilisateur

B-TEK Scales

B-TEK Scales Super Sack Manuel utilisateur

B-TEK Scales

B-TEK Scales WorldWEIGH PGE-W Series Manuel utilisateur

B-TEK Scales

B-TEK Scales AquaShield Series Manuel utilisateur

Manuels Échelle populaires d'autres marques

AWS

AWS ZEO-50 Manuel utilisateur

Gima

Gima Glass Body Fat Analyzer Manuel de la liste des pièces

Seca

Seca 374 Manuel utilisateur

TEC

TEC TEC SL59 SERIES Manuel utilisateur

Axis

Axis B/E Series Manuel utilisateur

Alecto

Alecto ACW-40 Manuel utilisateur

Rice Lake

Rice Lake MSI-4260 IS Manuel utilisateur

IKA

IKA RCT basic safety control Manuel utilisateur

ADE

ADE M20011 Manuel utilisateur

Duronic

Duronic KS3000 Manuel utilisateur

Digi

Digi SM-720 Manuel utilisateur

Cardinal

Cardinal CS Series Manuel utilisateur

Korona

Korona Kastella Manuel utilisateur

A&D

A&D FC-50Ki Manuel utilisateur

BDA

BDA CAMARGUE Manuel utilisateur

Tanita

Tanita HD-357 Manuel utilisateur

Leifheit

Leifheit 03173 Manuel utilisateur

Lumme

Lumme LU-1340 Manuel utilisateur