AZZA 6VBD Manuel utilisateur

VIA 82C693

MAINBOARD

( VER. 1.x )

USER’S MANUAL

DOC. NO. UM-IBD-E1 ...................................................................PRINTED IN TAIWAN

VIA 82C693 MAINBOARD TABLE OF CONTENTS

TABLE OF CONTENTS

Chapter & Section Page

1. INTRODUCTION ..................................................................................1-1

1.1 OVERVIEW .................................................................................................1-1

1.2 MAINBOARD LAYOUT ...........................................................................1-2

1.3 SPECIFICATIONS......................................................................................1-3

2. INSTALLATION ...................................................................................2-1

2.1 UNPACKING ...............................................................................................2-1

2.2 AMAZING WAYS TO POWER ON THE PC SYSTEM........................2-1

2.3 POWER OFF THE PC SYSTEM ..............................................................2-5

3. HARDWARE SETUP...........................................................................3-1

3.1 INSTALLATION OF CPU .........................................................................3-1

3.2 INSTALLING THE DRAM MODULES ...............................................3-2

3.3 CONNECTORS............................................................................................3-4

3.4 JUMPERS.....................................................................................................3-16

4. AWARD BIOS SETUP ........................................................................4-1

4.1 GETTING STARTED ................................................................................4-1

4.2 MAIN MENU ..............................................................................................4-2

4.3 CONTROL KEYS.......................................................................................4-2

4.4 STANDARD CMOS SETUP.....................................................................4-3

4.5 BIOS FEATURES SETUP........................................................................4-4

4.6 CHIPSET FEATURES SETUP................................................................4-7

4.7 POWER MANAGEMENT SETUP .........................................................4-12

4.8 PNP/PCI CONFIGURATION...................................................................4-16

4.9 INTEGRATED PERIPHERALS ..............................................................4-20

4.10 LOAD SETUP DEFAULTS......................................................................4-23

4.11 SUPERVISOR PASSWORD / USER PASSWORD.............................4-24

4.12 IDE HDD AUTO DETECTION ..............................................................4-25

4.13 SAVE & EXIT SETUP .............................................................................4-26

4.14 EXIT WITHOUT SAVING ......................................................................4-27

VIA 82C693 MAINBOARD

SOMETHING IMPORTANT !

¶TRADEMARKS

All trademarks used in this manual are the property of their respective owners.

¶LOAD SETUP DEFAULTS

“LOAD SETUP DEFAULTS” is the function which will have the BIOS default

settings loaded into the CMOS memory, these default settings are the best-case

values which will optimize system performance and increase system stability This

function will be necessitated when you receive this mainboard, or when the system

CMOS data is corrupted. Please refer to the Section 4.8 for the procedures.

¶DISCHARAGE CMOS DATA

Whenever you want to discharge the CMOS data or open the system chassis, Make

sure to disconnect the AC power first because there is always the 5V standby voltage

connected to the ATX form-factor mainboard. Without disconnecting the AC power

connector from the PC system, the mainboard can be damaged by any improper

action .

¶WAKE ON LAN

In order to support the Wake On LAN feature, the system requires a special SPS

(Switching Power Supply), Such power supply must be able to provide at least 700

mA of driving capability on the “5V standby” voltage. Please refer to the Section 3.3

for pin assignment.

¶WARNING !

The "Static Electricity" may cause damage to the components on the mainboard, In

order to avoid the damage to the mainboard accidentally, please discharge all static

electricity from your body before touching this mainboard.

¶NOTICE

Information presented in this manual has been carefully checked for reliability;

however, no responsibility is assumed for inaccuracies. The information contained in

this manual is subject to change without notice.

VIA 82C693 MAINBOARD INTRODUCTION

1-1

1. INTRODUCTION

1.1 OVERVIEW

This mainboard is a high performance personal computer mainboard with100MHz ultra

high front side bus frequency designed for Pentium™ II and Celeron™ processors. It is

an ATX form-factor mainboard with A.G.P. (Accelerated Graphics Port) and PCI Local

Bus on board, Designed based on the VIA 82C693 chipset and Winbond® I/O chipset,

built-in two channel “PIO” and “Ultra DMA/33 Bus Master” mode PCI IDE ports, one

Floppy Disk control port, two high speed Serial ports (UARTs) and one multi-mode

Parallel port and supports PS/2™ mouse, IR and USB ports. It is designed for 233MHz,

266MHz, 300 MHz, 333MHz , 350MHz, 400MHz and 450MHz high performance

Pentium™ II and Celeron™ (S.E.C. Cartridge) processor for high-end and true

GREEN-PC computer systems.

The Pentium™ II Processor is a 64-bit processor with RISC technology, which offers

several key features such as built-in L2 cache (256KB/512KB), 12-stage super-pipeline

architecture, out of order execution .... etc. In order to optimize its capabilities and

performances, the 32-bit Operating System (such as Windows® NT and OS/2™) and

32-bit applications are recommended.

The Accelerated Graphics Port (A.G.P.) on the mainboard is designed for AGP 3D

video display card. Unlike PCI-based display cards, the AGP technology provides

lightning data throughput to fully facilitate the 3-Dimensional and multimedia graphics

display. The data transfer rate on AGP can be up to 133Mhz and which is much faster

than the traditional 33MHz PCI VGA card.

The AGP is a new video display technology and it requires device driver or new

Operating System to enable this accelerated graphic feature. Windows® 98 supports

AGP directly but Windows® 95 still need the appropriate device drivers to support

AGP feature. Please don’t worry about the device driver, because you can always find

the device driver included in the AGP cards. Regarding the definition of AGP interface

and its functionality, please refer to the latest A.G.P. Interface Specification. which can

be found at the Intel web site, the URL is “developer.intel.com/technology/agp”

VIA 82C693 MAINBOARD INTRODUCTION

1-2

1.2 MAINBOARD LAYOUT

PCISLOT

USB

PCISLOT

BAT1

SLOT1

SPKR

AGPSLOT

ISASLOT

PCISLOT

CN1

CN3,CN6,CN7

CN2

CN9IDE2

CN10IDE1

CN11FDC

CN4

BIOS

KBLOCK

CN1

CPUFAN

CN14

PCISLOT

JP100

VIA 82C693 MAINBOARD INTRODUCTION

1-3

1.3 SPECIFICATIONS

¥CPU

Intel® Pentium™ II and Celeron™ processor 233 MHz, 266 MHz, 300 MHz,

333MHz. 350MHz, 400MHz and up to 450MHz.

¥CPU VCC

Switching Voltage Regulator circuits on board, supports +1.80V DC through

+3.5V DC CPU Core Voltage.

Note : The CPU Core Voltage will be Detected and adjusted automatically by the

VID-pin on the CPU, so there is no manual-adjustment required to select the CPU

voltage. Simply plug in the CPU and start immediately.

¥WORD SIZE

Data Path : 8-bit, 16-bit, 32-bit, 64-bit

Address Path : 32-bit

¥PC SYSTEM CHIPSET

VT 82C693, VT 82C596A

¥SUPER I/O CHIPSET

Winbond® W83977TF-AW

¥FRONT SIDE BUS FREQUENCY

66 MHz and 100MHz selectable.

¥MEMORY

DRAM : Four 168-pin DIMM sockets are designed onboard which support 8, 16,

32,64 or 128MB 3.3V SDRAM DIMM module. Maximum memory size can be up

to 512 MB with Parity / ECC (Error Checking and Correcting) supported.

CACHE:512KB pipelined burst SRAM built-in Pentium™ II processor. 0KB or

128KB SRAM in Celeron™ processor.

¥BIOS

AWARD System BIOS. 128KB x 8 Flash ROM

(Supports Plug & Play, ACPI, DMI and Green functions).

VIA 82C693 MAINBOARD INTRODUCTION

1-4

¥EXPANSION SLOTS

AGP Slots : 32-bit x 1 (Supports 1x or 2x AGP graphics cards)

PCI Slots : 32-bit x 5 (All Master/Slave, PCI 2.1 Compliant)

ISA Slots : 16-bit x 2 (One of the slot is PCI/ISA shared)

¥WOL PORTS

One WOL connector supports Wake-On-LAN (WOL up-designed)

¥SB-LINK PORTS

One SB-LINK feature connector to support PCI sound cards. (such as Creative™

Labs EMU8008 sound chip)

¥USB PORTS

Two Universal Serial Bus (USB) ports.

¥IDE PORTS

Two channels of Ultra DMA/33 Bus Master IDE ports, which will support up to 4

IDE devices like IDE hard disk, ATAPI CD-ROM and LS-120/ZIP-100 devices.

The IDE ports can be programmed to support PIO Mode 4, DMA mode 2 and Ultra

DMA/33.

¥SUPER I/O PORTS

1. Two high speed NS16C550 compatible serial ports (UARTs).

2. One parallel port, supports SPP/EPP/ECP mode.

3. One Floppy Disk Control port.

¥IR PORT

One HPSIR and ASKIR compatible IR transmission connector (5-pin).

One Consumer IR transmission connector (4-pin, optional).

¥MOUSE AND KEYBOARD

One PS/2™ mouse connector, One PS/2™ keyboard connector.

VIA 82C693 MAINBOARD INTRODUCTION

1-5

¥HARDWARE MONITORING (optional)

Winbond W83781D is designed on the board to monitor hardware healthy status

like system voltage, system temperature, and cooling fans. When the CPU is over

heated, the system BIOS will tell the system board to give a series of beeping alarm

and then slow down the CPU speed (throttling speed) so that you can take proper

action to prevent your system from damage. When you hear the beeping alarm, be

sure to turn the power off and check on the cooling fans (especially the CPU

cooling fan ) to see whether it is working properly or not. If you don’t know how to

handle it, send the PC system to your dealer for technical support.

This mainboard includes the hardware monitoring program and you can use it to

monitor the system healthy status. When you find there is the Winbond W83781D

installed on the board, you can run the hardware monitoring program which comes

in the CD disc and then it will monitor the system healthy status all the time.

¥ACPI

Advanced Configuration and Power Interface (ACPI) function is strongly

recommended by PC’98 because it will let you have many additional features and

that will make your PC system becomes very friendly and convenient. Followings

are the ACPI features designed on the board:

1. On Now: power on the system by panel-switch, Keyboard, PS/2™ Mouse,

Modem ring-in, RTC alarm or LAN signal.

2. Power off (soft-off) by OS or Panel-switch.

3. CPU cooling fan auto-off during Suspend state.

4. Resuming of PC system. (such as Modem ring-in, RTC alarm, .... etc.)

5. Supports Full-On/Doze/Standby/Suspend operating modes.

¥DIMENSION

1. Width & Length : 305 mm x 190 mm.

2. Height : 2 1/2 inches with CPU Retention Mechanism.

3. PCB Thickness : 4 layers, 0.05 inches normal.

4. Weight : 18 ounces.

ENVIRONMENT LIMIT

1. Operating Temperature : 10to 40. (50to 104)

2. Required Airflow : 50 linear feet per minute across CPU.

3. Storage Temperature : - 40to 70. (- 40to 158)

4. Humidity : 0 to 90% non-condensing.

5. Altitude : 0 to 10,000 feet.

VIA 82C693 MAINBOARD INSTALLATION

2-1

2. INSTALLATION

2.1 UNPACKING

The mainboard contains the following components. Please inspect the following

contents and confirm that everything is there in the package. If anything is missing or

damaged, call your supplier for instructions before proceeding.

lThis mainboard.

lOne USER‘S MANUAL.

lOne Cable set for IDE and Floppy devices.

lOne Pentium™ II Processor Retention Mechanism (RM).

lOne CD diskette for device driver and utility programs.

This mainboard contains electrostatic sensitive components and it can be easily

damaged by static electricity. So please leave it sealed in the original packing until

when installing.

A grounded anti-static mat is recommended when unpacking and installation. Please

also attached an anti static wristband to your wrist and have it grounded to the same

point as the anti-static mat.

After the opening of the mainboard carton, please observe the mainboard carefully to

make sure there is no shipping and handling damage before you can start to install the

PC system.

Having finished all the procedures above, you are now ready to install the mainboard to

the chassis. Please make sure that the chassis is the ATX type so that the mounting hole

will match with this mainboard.

2.2 AMAZING WAYS TO POWER ON THE PC SYSTEM

When the mainboard has been installed successfully, there are several ways to power

on the system. Please read the following description for all the details.

VIA 82C693 MAINBOARD INSTALLATION

2-2

POWER BUTTON

The power button can be programmed by COMS setup program and it has different

features. Please refer to page 3-23 and page 3-24 for detail function description.

Note: This power button can not be used to power-on the PC system if the

”Password“ is selected to power on your system. (please refer to Section 4.8 for

the “INTEGRATED PERIPHERALS“ in the CMOS setup.) However, you can

always use the power button to turn off the power.

¨KEYBOARD (PASSWORD OR HOT KEY)

It is a nightmare when someone uses your PC system without your permission and

modifies or destroys all the valuable data stored in the system. Now the problem can

be avoided by using this mainboard because it allows you to enter your personal

password or a combination of hot key so that you can use it to power on your

system. When the system power is off, This mainboard still keeps scanning the

keyboard status waiting for the correct password or hot key input to turn on the

system power (the stand-by 5V is still working and the power LED on the keyboard

is still active). Without the correct password or hot key, no one else can turn on the

PC system ( neither by the power button ). So the PC system is secured for you.

There are two ways to power-on the PC system by keyboard, they are “Password”

and “Hot KEY”. Please refer to Section 4.8 for the BIOS setup.

When the “Password” and “Hot KEY” is selected, you will have to reboot the PC

system to activate the setting, when you see the POST (Power On Self Test) is

completed, the setting is changed and stored in the CMOS memory. Having finished

the procedure, you may turn the power off and then you can use the keyboard to

power-on the PC system afterward.

In case that you forget the “Password” or “Hot Key”, disconnect the AC power for

30-60 seconds then re-connect the AC power to the PC system, the power button

will be activated again and you can use the power button to turn on the system.

Input your personal password again in the BIOS setup program, and then you may

use the new password to power-on the PC system afterward.

¨PS/2™ MOUSE (MOUSE LEFT OR MOUSE RIGHT BUTTON)

When you are tired of pressing on the power button or keying in the password to

turn on the PC system, there is another extremely convenient way for you.

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels AZZA Carte mère

AZZA

AZZA PT-6IET Manuel utilisateur

AZZA

AZZA 6IFB Manuel utilisateur

AZZA

AZZA 366A-AV Manuel utilisateur

AZZA

AZZA 694TX Manuel utilisateur

AZZA

AZZA P4X4-ALH Manuel utilisateur

AZZA

AZZA P4M2-MVB Manuel utilisateur

AZZA

AZZA 810T Series Manuel utilisateur

AZZA

AZZA 845S Series Manuel utilisateur

AZZA

AZZA U601 Series Manuel utilisateur

AZZA

AZZA 366 Series Manuel utilisateur

AZZA

AZZA P4X2 Series Manuel utilisateur

AZZA

AZZA KM266-MNB Manuel utilisateur

AZZA

AZZA 361 BM Manuel utilisateur

AZZA

AZZA P4X2-AV Manuel utilisateur

AZZA

AZZA PT-5IH Manuel utilisateur

AZZA

AZZA 6IL Manuel utilisateur

AZZA

AZZA PT-5V3T Manuel utilisateur

AZZA

AZZA KT33-BV Manuel utilisateur

AZZA

AZZA U694 Series Manuel utilisateur

AZZA

AZZA KM266-MVB Manuel utilisateur

AZZA

AZZA KT133TX Manuel utilisateur

AZZA

AZZA P4XA Series Manuel utilisateur

AZZA

AZZA DVAX2+ Manuel utilisateur

AZZA

AZZA 810DTC Manuel utilisateur

Manuels Carte mère populaires d'autres marques

DFI

DFI SD170 Manuel utilisateur

ASROCK

ASROCK ROMED8-2T Manuel utilisateur

Asus

Asus P2L97A Manuel utilisateur

Winmate

Winmate IC70 Manuel utilisateur

Asus

Asus MES-B Manuel utilisateur

Grantech

Grantech SYS8F377VGGA-3OMN Manuel utilisateur

Telit Wireless Solutions

Telit Wireless Solutions SL869-3DR Manuel utilisateur

Gigabyte

Gigabyte GA-9IVDT Manuel utilisateur

Texas Instruments

Texas Instruments ADS8372EVM Manuel utilisateur

Commell

Commell MS-C73 Manuel utilisateur

IBT Technologies

IBT Technologies MB860 Manuel utilisateur

Nvidia

Nvidia TEGRA DG-04927-001_V01 Manuel utilisateur

Biostar

Biostar M7VIT Bravo Instructions d'utilisation et d'installation

Intel

Intel D33217CK Manuel utilisateur

Asus

Asus F1A55-M LX PLUS R2.0 Manuel utilisateur

EPC

EPC EPC9147C Manuel utilisateur

Asus

Asus EX-B760M-V5 D4 Manuel utilisateur

EPOX

EPOX MU-8KHA0010 Manuel utilisateur