Axxess AXDSP-L Manuel utilisateur

AXDSP-L
INSTALLATION INSTRUCTIONS
AxxessInterfaces.com © COPYRIGHT 2020 METRA ELECTRONICS CORPORATION REV. 3/2/20 INSTAXDSP-L
Google Play Store Apple App Store
iOS 12.1 or higher
INTERFACE FEATURES
INTERFACE COMPONENTS
TOOLS & INSTALLATION ACCESSORIES REQUIRED
• Crimping tool and connectors, or solder gun,
solder, and heat shrink • Tape • Wire cutter
• Zip ties • Multimeter
TABLE OF CONTENTS
Preface ....................................................................2
Installation Options ...............................................3
Installation .............................................................3
Connections ........................................................ 4-7
AXDSPL-BT Installation ..........................................8
AXDSPL-SP Installation ..........................................9
Mobile App ...................................................... 10-19
Pinout ...................................................................20
Specifications ........................................................21
Axxess 6-Channel Digital Signal Processor
• 15 Band graphic EQ
• 4 inputs and 6 outputs, including front, rear, and subwoofer
• Independent equalization for front, rear, and sub
• Independent crossover for front, rear, and sub
• Selectable slope (12, 24, 36, or 48db per octave)
• Front and rear channels can be delayed independently up to 10ms
• Easy behind the radio installation in most applications
• Can be used with OE and aftermarket radios
• Chime control for GM/Chrysler vehicles
• Clipping detection and limiting circuits
• Internal header port for adding interface modules
• Bass knob included
• Retains OE voice prompts (SYNC® and OnStar®)
• Retains factory chimes including parking sensor and cross path
detection alerts
•
Settings adjusted via Bluetooth® in a smart device application (tablet
or mobile phone), compatible with both Android and Apple devices
• Read, write, and store configurations for future recall
• Password protect feature available in the mobile app
• Micro-B USB updatable
• AXDSP-L interface
• AXDSP-L harness (16-pin & 20-pin)

2
PREFACE
The AXDSP-L can be used with an aftermarket system or OEM system. The AXDSP-L can also grow as your stereo system grows. Start off by adding a subwoofer to an OEM system, then
add on from there. Simply reference the Installation Options page to change the AXDSP-L to the new system. All 6 channels of the AXDSP-L can be assigned however needed for the
installation at hand. If 6 channels of a subwoofer signal is needed, the AXDSP-L can do it.
In the following section,
Installation Options
, choose the installation type, then either click on the hyperlink, or reference the page number.
It is highly suggested to use an AXDSP-L pre-wired harness (sold separately) unless you are installing it with an aftermarket radio. As such, the instructions are written in that
manner. Certain connections to the vehicle are unique per vehicle and will require the pre-wired harness to reference to.
The AXDSP-L provides a 12v 1-amp output to turn on an aftermarket amplifier. If installing multiple amplifiers, an SPDT automotive relay will be required if the current exceeds that
amount. Use Metra part number E-123 (sold separately) for best results.
If installing the AXDSP-L behind the radio to install a sub amp, the OEM amp can be retained for mids/highs. If installing the AXDSP-L at the OEM amp location, the OEM amp must be
fully removed.
In most cases the CAN Bus wires need to be connected in order for the AXDSP-L to communicate with the vehicle to turn on and provide an amp turn-on output.
Inside the interface is a 16-pin header port for adding optional modules (sold separately). Page 8 and Page 9 will show the installation and use of these modules.
• AXDSPL-BT - Bluetooth streaming interface
• AXDSPL-SP - Toslink digital output

3
REV. 3/2/2020 INSTAXDSP-L
Aftermarket radio system:
The AXDSP-L can be used with an aftermarket radio to improve the overall listening experience for
car audio enthusiasts. Installers will connect the RCA inputs from the AXDSP-L to the outputs from
the aftermarket radio; Front, Rear. When using an aftermarket radio with the AXDSP-L, General
must be chosen for the vehicle type.
(refer to page 4)
Adding a subwoofer to an OEM System:
This feature offers the Installer the ability to add an aftermarket subwoofer to an OEM system. If the
vehicle is equipped with noise canceling microphoness, they must be disabled for this type of system.
(refer to page 5)
Adding a full-range amplifier and subwoofer* to an OEM system:
Similar to adding a subwoofer as mentioned prior, except for one extra step required to configure
the harness for a full-range setup. Also note, if only adding the AXDSP-L to just the front or rear
channels is desired, this can be accomplished by just using the necessary front or rear speaker wires
and leaving the other speaker wires still connected.
(refer to page 6)
* Subwoofer is optional
Stand-alone Bluetooth system:
The AXDSP-L and AXDSP-BT can be used together as a stand-alone system and used in just about
any 12V DC application. Perfect applications would be classic car installations where the dashboard
cannot be altered, or in UTV vehicles. This can even be used inside a home with a 12v DC power
supply. The options are endless and only limited by ones creativity.
(refer to page 7)
Aftermarket Radio Systems
1. Complete all necessary connections to the radio and vehicle, but leave the amp
turn-on wire disconnected.
Continue to All Systems
Factory Radio Systems
1. Remove the factory radio*, then unplug all connectors.
2. Install the vehicle specific T-harness (sold separately) and make all necessary
connections, but leave the amp turn-on wire disconnected.
* Refer to Metra online for dash disassembly. If Metra makes a dash kit for the
vehicle, disassembly will be within the instruction booklet.
Continue to All Systems
All Systems
1. Plug the 20-pin AXDSP-L harness into the AXDSP-L.
2. Plug the 16-pin AXDSP-L harness into the AXDSP-L.
3.
Download and install the
AX-DSP-X app
from the Google Play Store or Apple App
Store
.
4. Open the app then select Bluetooth Connection tab. Follow the instructions to pair
the mobile device to the AXDSP-L.
5. Scroll to the Configuration tab then select the vehicle type. Press the Lock Down
button to save the configuration.
6. Connect the amp turn-on wire.
7. Adjust the settings in the app as desired. Press the Lock Down button to save any
new configurations.
INSTALLATION OPTIONS I N S TAL L ATI O N

4
FrontRear
Sub
BASSKNOB (included)
Aftermarket Radio
AXDSP-L (included)
Do not use amp turn-on
from aftermarket radio!
Any remaining wires
tape off and disregard
Blue/White - Amp Turn-On Wire
INPUT 5
INPUT 6
Do Not Use
Black - Chassis Ground
Yellow - Battery Power
Red - Accessory Power
An SPDT relay, Metra part number
E-123, must be used if more than
one amplifier will be installed
5
5
4
3
2
1
RCA Jacks
(sold separately)
Black - Chassis Ground
Orange - Control Wire
AFTERMARKET RADIO SYSTEM

5
REV. 3/2/2020 INSTAXDSP-L
ADDING A SUB TO AN OEM SYSTEM
Factory Radio
Factory Radio Harness
Refer to pre-wired harness
for wire connections
AX-DSP-LITE pre-wired
harness (sold separately)
These outputs can be used for
additional sub amps, or for adding
onto the system at a later date
5
5
4
3
2
1
RCA Jacks
(sold separately)
BASSKNOB (included)
AXDSP-L (included)
Keep Connected
Any remaining wires
tape off and disregard
Blue/White - Amp Turn-On Wire

6
ADDING A FULL-RANGE AMP & SUB TO AN OEM SYSTEM
Factory Radio
Refer to pre-wired harness
for wire connections
AXDSP-L pre-wired
harness (sold separately)
5
5
4
3
2
1
BASSKNOB (included)
AXDSP-L (included)
Unplug Connecter
Factory Radio Harness
RCA Jacks
(sold separately)
An SPDT relay, Metra part number
E-123, must be used if more than
one amplifier will be installed
Cut the male
connector off and
connect speaker wires
to amp
White / Front Left +
White/Black / Front Left -
Gray / Front Right +
Gray/Black Front Right -
Green / Rear Left +
Green/Black / Rear Left -
Purple / Rear Right +
Purple/Black / Rear Right -
Blue/White - Amp Turn-On Wire
Any remaining wires
tape off and disregard

7
REV. 3/2/2020 INSTAXDSP-L
STAND-ALONE BLUETOOTH SYSTEM
Do Not Connect
AXDSP-L (included)
Any remaining wires
tape off and disregard
Blue/White - Amp Turn-On Wire
INPUT 5
INPUT 6
Black - Chassis Ground
Yellow - Battery Power
Red - Accessory Power
An SPDT relay, Metra part number
E-123, must be used if more than
one amplifier will be installed
5
5
4
3
2
1
RCA Jacks
(sold separately)
Black - Chassis Ground
Orange - Control Wire
Black - Chassis Ground
Brown - Control Wire
BASSKNOB (included)BASSKNOB (sold separately)
Sub Control
Volume Control

8
BLUETOOTH INTERFACE
16-pin Header
16-pin Header
AX-DSPL-BT
AX-DSPL-SP
AX-DSPL-BT
AX-DSPL-SP
• The AXDSPL-BT will be used for adding a Bluetooth interface to the AXDSP-L for
playing music files directly to the interface.
• While playing music the volume on the phone will be used. As an option, the
AXBK-1 (sold separately) can be used to control the volume.
Note: The AXBK-1 included with the AXDSP-L can also be used if it will not be used to
control a subwoofer.
1. Important! Unplug the AXDSP-L from the vehicle.
2. Remove (4) Phillips screws securing the AXDSP-L interface, then remove the top cover,
exposing the circuit board within.
3. Locate the 16-pin header on the circuit board.
4. Important! Referencing how the Bluetooth interface is laid out in the picture, carefully
line up the header pins to the AX-DSPL-BT Bluetooth interface. Gently press down to
secure.
Note: Both interfaces may be damaged if installed wrong.
5. Reinstall the top cover to complete the installation.
AXBK-1 installation:
6. Connect the Brown wire from the AXDSP-L to the Orange wire from the
AXBK-1. Ground the Black wire from the AXBK-1.
Continued on the next page

9
REV. 3/2/2020 INSTAXDSP-L
DIGITAL OUT INTERFACE
16-pin Header
16-pin Header
AX-DSPL-BT
AX-DSPL-SP
AX-DSPL-BT
AX-DSPL-SP
• The AXDSPL-BT will be used for adding a Toslink digital output to the AXDSP-L.
1. Important! Unplug the AXDSP-L from the vehicle.
2. Remove (4) Phillips screws securing the AXDSP-L interface, then remove the top cover,
exposing the circuit board within.
3. Locate the 16-pin header on the circuit board.
4. Important! Carefully line up the header pins to the Toslink interface, with the Toslink
port facing outward. Gently press down to secure.
Note: Both interfaces may be damaged if installed wrong.
5. Reinstall the top cover provided with the AX-DSPL-BT to complete the installation.
Continued on the next page

10
MOBILE APP
Setup Instructions
The AXDSP-L uses the same app as the AXDSP-X. Only items pertaining
to the AXDSP-L will be shown.
• General information tab for installing the AXDSP-L.
Continued on the next page
Table des matières
Autres manuels Axxess Matériel informatique
Manuels Matériel informatique populaires d'autres marques

EMC2
EMC2 VNX Series Manuel du propriétaire

Panasonic
Panasonic DV0PM20105 Manuel utilisateur

Mitsubishi Electric
Mitsubishi Electric Q81BD-J61BT11 Manuel utilisateur

Gigabyte
Gigabyte B660M DS3H AX DDR4 Manuel utilisateur

Raidon
Raidon iT2300 Manuel utilisateur

National Instruments
National Instruments PXI-8186 Manuel utilisateur












